-
KitchenAid KHPF 7510/I - page 1
KHPF 7510 KHPS 7510 Instructions for use 5019_719_01132_GB 1-06-2007 14:30 Pagina 1 ...
-
KitchenAid KHPF 7510/I - page 2
5019_719_01132_GB 1-06-2007 14:30 Pagina 2 ...
-
KitchenAid KHPF 7510/I - page 3
Product description and symbols 4 Using the burners 4 Practical advice on using the hob 5 Positioning the pan supports and wok suppor t 5 Hood and cabinetry clearances (mm) 6 Injector table 6 W arnings and suggestions 7 Safeguarding the environment 8 Installation (Flush and T raditional fitting) 9 Gas connection 9 Electrical connection 10 Fixing th ...
-
KitchenAid KHPF 7510/I - page 4
1. Removable pan supports 2. 1 kWh auxiliary burner 3. 1.65 kWh semi-fast burner 4. 1.65 kWh semi-fast burner 5. Professional wok burner 6. Auxiliary burner control knob 7. Semi-fast burner control knob 8. Semi-fast burner control knob 9. Professional wok burner control knob Control Symbols Off Maximum flame Minimum flame Product description and sy ...
-
KitchenAid KHPF 7510/I - page 5
Read the instructions to get the best out of your hob. • Use pans with a similar diameter to the burner(see the table). • Use flat bottomed pans except with the wok support. • Do not use excessive water when cooking foods and use the lid. • Ensure that pans are fully supported by the pan supports and do not protrude over the edges. Y ou sho ...
-
KitchenAid KHPF 7510/I - page 6
Category II2H3+ Electric P ower: 230 V - 50 Hz If a hood is to be installed above the hob, refer to the hood installation instructions to ensure the correct height above the hob. Note: If the distance “ A ” between the kitchen wall cabinets is between 600 and 730 mm, height “B" shall be at least 530 mm. If the distance “ A ” between ...
-
KitchenAid KHPF 7510/I - page 7
T o get the most out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose destination symbol is shown on the serial number plate on the hob. • The packing (plastic bags, expanded polyurethane, etc) pose a potential threat to children and should be d ...
-
KitchenAid KHPF 7510/I - page 8
P acking The packing material is 100% recyclable and is labelled with the recycling symbol . Please dispose of all packing responsibly and carefully . Product This appliance is marked according to the European Directive 2002/96/EC, W aste Electrical and Electronic Equipment (WEEE). By ensuring that this product is disposed of correctly , you will h ...
-
KitchenAid KHPF 7510/I - page 9
T echnical information for the installer • W arning: this is a heavy products which requires the installation to be carried out by two people. • When installing the hob it is advisable to wear protective gloves. • This appliance can be installed into a 20mm - 50mm thick worktop. • If no oven is to be installed below the hob, a panel must be ...
-
KitchenAid KHPF 7510/I - page 10
The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. plate. • The appliance must be earthed. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch. • If damag ...
-
KitchenAid KHPF 7510/I - page 11
Important: The following procedure shall be carried out by competent technical personnel only . The hob can be installed on different types of materials, such as masonry , metal, bare wood and heat resistant laminate coated wood (90°C). Cut an opening into the worktop to the dimensions shown in the diagram. In order to correctly fit this type of h ...
-
KitchenAid KHPF 7510/I - page 12
Note: Refer to the injector table to ensure the correct type of injector is to be fitted. T raditional burners (T) 1. Remove the pan supports (A). 2. Remove the burners (B). 3. Unscrew the injector (C) with a box spanner 7. 4. Replace the injector with the one for the new gas. 5. Replace burners and pan supports. Note: Before installing the hob, pl ...
-
KitchenAid KHPF 7510/I - page 13
T o fit the double crown wok burner: Insert in the following order: 1. burner ring ( A ); 2 . decorative covering ring ( B ); 3. external burner cap ( C ); 4. internal burner cap ( D ). Note: make sure that: 1. the locating pin for the burner ring ( A ) is inserted correctly in the slot on the burner unit. 2. that the locating pin on the external b ...
-
KitchenAid KHPF 7510/I - page 14
Always disconnect the hob from the electrical power supply and wait until it cools before cleaning and/or doing maintenance work. n order to keep your hob in good condition, you must keep it clean, removing any remaining food each time you use it. Cleaning the hob surface: • the stainless steel surface may become stained if it comes into contact ...
-
KitchenAid KHPF 7510/I - page 15
If the hob is not working properly , work through this guide before contacting our Customer Care Centre. The burner does not ignite, or the flame is unsteady? Check that: 1. the gas, or electricity supply has not been interrupted and that the control knob is turned fully on. 2. the gas supply has not run out. 3. the openings on the burner have beco ...
-
KitchenAid KHPF 7510/I - page 16
5019 719 01132 Printed in Italy n 06/07 GB Whirlpool Europe S.r .l. Viale G. Borghi, 27 - 21025 Comerio (V A) Phone 0332.759111 - Fax 0332.759268 www .whirlpool.eu 5019_719_01132_GB 1-06-2007 14:30 Pagina 16 ...
¿Tienes una pregunta acerca de KitchenAid KHPF 7510/I?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con KitchenAid KHPF 7510/I, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con KitchenAid KHPF 7510/I probablemente compartirá una forma de solucionarlo.