-
Cadet CDT7 - page 1
Read these instructions bef ore operating the machine MODEL: CDT7 10080220 Operating Instructions 86038220 04/26/11 AD CARPET EXTRACTOR CU S 3146518 ...
-
Cadet CDT7 - page 2
MACHINE DATA LOG/OVERVIEW CADET 86038220 1 Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve y ou better over the lifetime of the product. To register your product go to: www.windsorind.com/WarrantyRegistration.aspx For customer assistance: 1-888-444-7 ...
-
Cadet CDT7 - page 3
TABLE OF CONTENTS CADET 86038220 2 Machine Data Log/Overview. ........................ 1 Table of Contents .......................................... 2 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1-1 SAFETY Important Safety Instructions ........................ 2-1 Hazard Intensity Level ......................... ...
-
Cadet CDT7 - page 4
HOW TO USE THIS MANUAL CADET 86038220 1-1 This manual contains the f ollowing sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authori zed dealers. When placing an order f ...
-
Cadet CDT7 - page 5
SAFETY INSTRUCTIONS CADET 86038220 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet ...
-
Cadet CDT7 - page 6
SÛRETÉ CADET 86038220 2-2 IMPORTANTES MESURES DE SÉCURITÉ L’utilisation d’un appareil électri que demande certaines précautions: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAI RE FONCTIONNER (CET APPAREIL). Pour réduire les risques d’incen d i e, d e choc électrique ou de blessure: Cet appareil ne doit être connecter qu a des pri ses ayan ...
-
Cadet CDT7 - page 7
HAZARD INTENSITY LEVEL CADET 86038220 2-3 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Ha ...
-
Cadet CDT7 - page 8
DEGRÉS DE RISQUES EN CAS DE DANGER CADET 86038220 2-4 Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions : DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques iden tifiés par les termes signalétiques – AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque es ...
-
Cadet CDT7 - page 9
GROUNDING INSTRUCTIONS CADET 86038220 2- 5 ELECTRICAL: In the USA, this machine operates on a standard 15 amp 115V, 60 Hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label foun d on each machine. Using voltage s abov e or below those indicated on the data label will ca use serious damage to the motors. EXTENSION CORDS: I ...
-
Cadet CDT7 - page 10
TECHNICAL SPECIFICATIONS CADET 86038220 3-1 POWER TYPE ELECTRICAL: 115 V, 15 A, 60 HZ ELECTRIC VACUUM MOTOR: (1) –3 stage, 1.5 hp, 100 cfm (2.80 cubic meters/min.) Waterlift –120” (304 cm) BRUSH: (1) 15” (38.1 cm.) SOLUTION PUMP: 90 PSI, Diaphragm style, internal bypass SOLUTION CAPACITY: 7 gallons (26.5ltr) RECOVERY CAPACIT Y: 7 gallons (2 ...
-
Cadet CDT7 - page 11
CONTROLS/COMPONENT LOCATIONS CADET 86038220 3-2 1. Main Handle. Used to pull and maneuver machine. 2. Electrical Cord. 3. Pump Switch. Turns on pump and enables spray. 4. Brush/Spray switch. Turns on brush motor and activates electro-valve to dispense solutio n to floor through jets. Intermittent, off, and continuous settings. 5. Vacuum Motor Switc ...
-
Cadet CDT7 - page 12
CONTROLS/COMPONENT LOCATIONS CADET 86038220 3-3 1 2 3 10 9 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning t ools. 2. Vacuum Hose Door. Used to connect various auxiliary 1 ½ inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage positio n to variou s carpet heights. 4. Recover ...
-
Cadet CDT7 - page 13
CONTROLS/COMPONENT LOCATIONS CADET 86038220 3-4 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6 ...
-
Cadet CDT7 - page 14
FILLING OPERATIONS CADET 86038220 3-5 FILLING THE CADET NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemical s in the solutio n tank. Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank. CHEMICALS Suitable Chemicals No ...
-
Cadet CDT7 - page 15
OPERATIONS CADET 86038220 3-6 Remove literature from recovery tank. Fill solution tank (see filling operations, page3-5). Adjust brush to proper setting. Note: For good operation the brush must skim the carp et . If circuit breake r trips raise brush to prevent damage to motor or carpet. Plug cord into grounded ou tlet. Note: Be sure dome is seat e ...
-
Cadet CDT7 - page 16
OPERATIONS CADET 86038220 3-7 Select intermittent or continuous switch setting to turn on brush and start solution spray. The intermittent setting requires the operator to hold the switch in the “on” position with the thumb, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the operator to ...
-
Cadet CDT7 - page 17
CLEANING PROCEDURE CADET 86038220 3-8 1ft. (30cm) Release intermittent setting or turn off continuous setting on brush/spray swit ch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area approximately 1inch. During operation, observe t ...
-
Cadet CDT7 - page 18
CLEANING PROCEDURE CADET 86038220 3-9 To speed drying, use a Windblo wer ™ fan. Empty recovery tank by releasing dum p hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. After cleaning, turn off all controls, return brush to storage position a nd ca refully unplug machine. Use right side of m ...
-
Cadet CDT7 - page 19
ACCESSORY TOOL USAGE CADET 86038220 3-10 Turn on Pump and Vacuum Switch. Note: Be sure intermittent/continuous switch is in center (off) position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following acceptable accessory tools. HT – 86000610 PRV NO. 89227 DD ...
-
Cadet CDT7 - page 20
MAINTENANCE CADET 86038220 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY QUARTERLY Check machine for cord damage * Check recovery dome an d gasket for damage and cleanliness * Check brush – sho uld be clean with no lint or strings attached * Inspect vac shoe for blockage; remove fibers with coat hanger, etc. * Check hose s f or wear, blockag es, ...
-
Cadet CDT7 - page 21
MAINTENANCE CADET 86038220 4-2 PERIODIC MAINTENANCE Twice a month, flush a white vinegar sol ution (One quart vinegar to two gallons of water) or anti- browning solution (mixed as directe d) through the extractor. This will prev ent build-up of alkaline residue in the system. If spray jets become clog ged, remove the spray tips, wash them thoroughl ...
-
Cadet CDT7 - page 22
MAINTENANCE CADET 86038220 4-3 Only qualified maintenance personne l are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectu er des réparations. VACUUM MOTOR REPLACEME NT 1. Turn off all switches and unplug machin e. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame ...
-
Cadet CDT7 - page 23
MAINTENANCE CADET 86038220 4-4 Only qualified maintenance personne l are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations. BELT REPLACEMENT 1. Turn off all switches and unplug machin e. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame ...
-
Cadet CDT7 - page 24
MAINTENANCE CADET 86038220 4-5 Only qualified maintenance personne l ar e to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des rép arations. SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the f ...
-
Cadet CDT7 - page 25
WIRING DIAGRAM CADET 86038220 4-6 86268450 PRV NO. 88332 86268830 PRV NO. 88636 86266890 PRV NO. 88655 86004480 PRV NO. 41353 ...
-
Cadet CDT7 - page 26
FRAME ASSEMBLY CADET 86038220 03/16/07 5-1 32 28 31 30 B 6 9 33 12 A 19 18 21 34 26 3 4 25 24 14 13 7 15 10 11 22 5 8 20 29 27 16 2 SEE SOLUTION TANK ...
-
Cadet CDT7 - page 27
FRAME ASSEMBLY CADET 86038220 03/16/07 5- 2 REF PART NO. PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 OPEN - - 2 86003620 34341 1 FRAME, CLP FAMILY 3 86004340 39528 1 HOSE ASM, 1.5 BLK VAC X 15.5 4 86001660 41236 2 HUBCAP, 5/8” SHAFT 5 86004480 41353 1 HARNESS, MAIN, CDT 6 86239610 41354 1 HINGE, TANK TO FRAME 7 86026150 53640 1 MOTOR ASM, B ...
-
Cadet CDT7 - page 28
BRUSH ASSEMBLY CADET 86038220 03/16/07 5-3 31 25 29 30 18 38 39 16 30 34 17 20 37 26 24 11 8 15 3 26 19 6 21 35 28 29 25 17 32 23 14 30 22 4 27 1 16 7 10 12 13 25 40 41 42 43 33 45 36 44 47 25 9 3 2 46 5 ...
-
Cadet CDT7 - page 29
BRUSH ASSEMBLY CADET 86038220 5-4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86000730 03110 1 AXLE, ROLLER 2 86227100 04084 1 ADAPTER, BRUS H BRG. 3 86000900 09019 2 BEARING, 1.125ODX.500IDX.375 4 86001100 11045 1 BELT, 180J6 MICRO-V 5 86001140 12514 1 BRUS H, 15L X 3.38OD 6 86001300 140343 1 BRKT, BRUS H PULLEY 7 86001310 140351 ...
-
Cadet CDT7 - page 30
PUMP ASSEMBLY CADET 86038220 03/16/07 5-5 PRIOR TO SERIAL NO. 1000166663 3 4 13 10 16 6 5 11 15 19 18 1 20 7 16 21 17 9 2 12 25 26 23 28 24 26 C 20 27 14 8 ( SEE SO LUTI ON TANK ) ...
-
Cadet CDT7 - page 31
PUMP ASSEMBLY CADET 86038220 03/16/07 5- 6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86002470 22072 1 COUPLING, 1/4 ANCHOR W/1" HEX 2 86002480 22090 2 CONNECTOR, 1/8FPT X 1/4 TUBEQC 3 86003470 31072 1 ELBOW, SWIVEL, 1/4MPTX1/4TUBE 4 86003480 31073 1 ELBOW, SWIVEL,1/4MPTX3/8TUBEQC 5 86004570 44067 2 JET BODY, MINI PROMAX BOD ...
-
Cadet CDT7 - page 32
PUMP ASSEMBLY CADET 86038220 03/16/07 5- 7 29 8 14 27 (SEE SOLUTION 20 C 26 24 26 12 23 2 9 17 21 16 7 20 1 18 19 15 11 5 6 16 10 13 3 TANK) 28 29 28 4 FROM SERIAL NO: 1000166663 ...
-
Cadet CDT7 - page 33
PUMP ASSEMBLY CADET 86038220 03/16/07 5-8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86032470 22072 1 COUPLING, 1/4 ANCHO R W/1" HEX 2 86002480 22090 2 CONNE CTOR, 1/8FPT X 1/4 TUBEQC 3 86003470 31072 1 ELBOW, SWIVEL, 1/4MPTX1/4TUBE 4 86003490 31074 1 ELBOW, SWIVEL, 3/8MPTX3/8TUBEQ C 5 86004570 44067 2 JET BODY, MINI PROMA X ...
-
Cadet CDT7 - page 34
VACUUM SHOE ASSEMBLY CADET 86038220 03/16/07 5-9 4 7 13 3 10 7 5 6 11 8 2 1 12 11 ...
-
Cadet CDT7 - page 35
VACUUM SHOE ASSEMBLY CADET 86038220 03/16/07 5-10 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86227350 05016 4 ARM, VAC SHOE PARALLEL 2 86234760 27674 1 COVER, ACCESSORY PORT 3 86005810 57245 4 NUT, 1/4-20 HEX NYLO CK SS 4 86006790 70351 2 SCR, 10-32 X 3/8 HHTR W/STAR 5 86275120 70360 4 SCR, 1/4-20 X.75 PPHMS PHIL 6 86006840 70390 ...
-
Cadet CDT7 - page 36
CONTROL PANEL ASSEMBLY CADET 86038220 03/16/07 5-11 12 16 11 4 9 14 5 13 15 19 6 1 18 17 10 7 2 8 3 D 20 21 22 4 23 SEE SOLUTION TAN K ...
-
Cadet CDT7 - page 37
CONTROL PANEL ASSEMBLY CADET 86038220 03/16/07 5-12 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86001240 14020 1 TERMINAL B LOCK, 115V (3-4-3) 2 86001980 14700 1 BREAKER, 15A 250VAC 50VDC 3 86230210 14832 1 BREAKER, 6A VDE CIRCUIT 4 86002010 14942 2 BOOT, 3/8 CI RCUIT BREA KER 5 86234320 23679 1 CORD ASM, 14/3 X 22" YLW 6 860 ...
-
Cadet CDT7 - page 38
SOLUTION TANK ASSEMBLY CADET 86038220 03/16/07 5-13 6 16* 14 18 5* 4 2 8 11* 22 18 15 19* 12 17 23 13B 7 3 29 18 10 1 9 21 20 A B D C 7* 25 24 27* 26* 28* 30* 33 32 34 13A 13 ASM SEE FRAME ASM SEE FRAME SEE CONTROL PANEL SEE PUMP ASM ...
-
Cadet CDT7 - page 39
SOLUTION TANK ASSEMBLY CADET 86038220 03/16/07 5-14 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86233140 20041 3 CLAMP, 2.0" WORM GEAR 2 86233150 20042 1 CLAMP, 3/8 HOSE (D-SLOT) 3 86003080 27809 1 COVER, VAC MOTOR 4 86003090 27810 1 COVER, BELT 5 86235500 31081 1 ELBOW, 3/8 MPT X 3/8 TUBE, PLASTIC 6 86003790 35175 2 GASKET, ...
-
Cadet CDT7 - page 40
RECOVERY TANK ASSEMBLY CADET 86038220 03/16/07 5-1 5 16 11A 7 1A E 12 9 2 6 17 13 8 4 15 5 10A 12 E 18 14A 3 1B 10B 11B 14B 12 ...
-
Cadet CDT7 - page 41
RECOVERY TANK ASSEMBLY CADET 86038220 03/16/07 5-16 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A 86002400 20064 1 CLAMP, 2.0" WORM GEA R X .312 1000083443 1B 86002350 20002 1 CLAMP, 2.0” WO RM GEAR 2 86233140 20041 1 CLAMP, 2.0" WORM GEA R 3 86008400 78499 1 CORD, DRAI N HOSE 4 86003110 27816 2 COVER, RE C. TANK 5 8623 ...
-
Cadet CDT7 - page 42
SUGGESTED SPARE PARTS CADET 86038220 03/16/07 5-17 PART NO. PRV NO. DESCRIPTION SERIAL # FROM NOTES: 86001140 12514 BRUSH, ASM, 15 IN 86001100 11045 BELT, 180J6 MICRO-V 86000900 09019 BEARING, 1. 125ODX.500IDX.375 86004570 44067 JET BODY, MINI PROMAX BODY 86004580 44068 JET, MINI PROMAX 9504 86026410 65257 PUMP ASM, 120V SHURFLO 10001666 63 8625890 ...
¿Tienes una pregunta acerca de Cadet CDT7?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cadet CDT7, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cadet CDT7 probablemente compartirá una forma de solucionarlo.