-
Makita HP2030 - page 1
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Hammer Drill 20 mm (3/4”) MODEL HP2030 20 mm (3/4”) MODEL HP2031 DOUBLE INSULA TION ...
-
Makita HP2030 - page 2
2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s ...
-
Makita HP2030 - page 3
3 Electrical Safety 4. Double insulated tools are equipped with a polarized plug (one blade is wider than the other .) This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, re verse the plug. If it still does not fit, contact a qualified elec- trician to install a polarized outlet. Do not change the ...
-
Makita HP2030 - page 4
4 21. Check f or misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool ser- viced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recom- mended by the manufacturer f or your model. Accessories that may b ...
-
Makita HP2030 - page 5
5 4. Keep hands awa y from rotating parts. 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Do not touch the bit or the w orkpiece immediately after operation; the y may be extremely hot and could b urn your skin. 7. Some material contains chemicals which may be to xic. T ake caution to prevent dust inhalation and skin con ...
-
Makita HP2030 - page 6
6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. • Switch can be lo ...
-
Makita HP2030 - page 7
7 Speed change T wo speed ranges can be preselected with the speed change le ver . T o change the speed, tur n the speed change le ver to the position 1 fo r low speed or the position 2 for high speed. If the speed change le ver does not turn easily , tur n the chuck slightly in either direction and turn the lev er again. Be sure that the speed cha ...
-
Makita HP2030 - page 8
8 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Installing side grip (auxiliary handle) Alwa ys use the side grip to ensure operating safe ty . Install the side grip so that the teeth on the grip fit in between the protrusions (A) on the tool barrel. Then tighten the ...
-
Makita HP2030 - page 9
9 Depth gauge The depth gauge is conv enient for drilling holes of unif or m depth. Loosen the side grip and inser t the depth gauge into the hole in the side grip . Adjust the depth gauge to the desired depth and tighten the side grip . NO TE: • The depth gauge cannot be used at the position where the depth gauge strikes against the tool body . ...
-
Makita HP2030 - page 10
10 Blow-out b ulb (optional accessor y) After drilling the hole, use the blo w-out bulb to clean the dust out of the hole. Drilling operation CA UTION: • Pressing e xcessively on the tool will not speed up the drilling. In fact, this e xcessive pressure will only serve to damage the tip of your bit, decrease the tool perf or mance and shor ten th ...
-
Makita HP2030 - page 11
11 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Cleaning vent holes The tool and its air vents ha ve to be k ept clean. Regular ly clean the tool ’ s air vents or whene v er the vents star t to become obstructed. T o maintain product SAFETY and RELIA ...
-
Makita HP2030 - page 12
Memo 12 ...
-
Makita HP2030 - page 13
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...
-
Makita HP2030 - page 14
14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...
-
Makita HP2030 - page 15
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair ...
-
Makita HP2030 - page 16
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o ...
¿Tienes una pregunta acerca de Makita HP2030?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita HP2030, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita HP2030 probablemente compartirá una forma de solucionarlo.