-
Sears 315.10924 - page 1
612547-480 SEARS OWNERS MANUAL MODEL NO. 315.109240 CAUTION" Read Rules for Safe Operation and Instructions Carefully SAVE THIS MANUAL FOR FUTURE REFERENCE 7-1/4 INCH CIRCULAR SAW. DOUBLE INSULATED Introduction Operation Maintenance Repair Parts 8125.47-480 7-87 Designed exclusively for and sold onlyby SEARS, ROEBUCK AND CO., Dept. 698/731A, S ...
-
Sears 315.10924 - page 2
FULL ONE YEAR WARRANTY ON CRAFTSMAN CIRCULAR SAW If this Craftsman Circular Saw fails to give complete satisfaction within one yearTff_o-_w-the date of purchase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears will repair it, free of charge. If this circular saw is used for commercial or rental purposes this warranty app ...
-
Sears 315.10924 - page 3
L heavy t usea loving doors. nask if ,t from ;ded to Jot use or best anging anging :d. to see it on. ger on )nly ex- marked lg _ and Jes. Do ove cut N OFF. . motor at your Always roleum- Do not qer part aperate moving qer con- _maged r. defec- IPPORT _tion re- d on the ...
-
Sears 315.10924 - page 4
RULES FOR SAFE OPERATION (Continued) 31. 32. 33. 34. 35. 36. 37. 38. b -- WARNING: ALWAYS RAISE THE LOWER BLADE GUARD WLT_._I';I ]'H E HANDLE TO AVOID SERIOUS INJURY. See Figure 14, Page 10. GUARD AGAINST KICKBACK. See Pages 7 and 8. BEFORE MAKING A CUT, BE SURE THE DEPTH AND BEVEL ADJUSTMENTS ARE TIGHT. DO NOT USE BLADES WITH INCORRECT S ...
-
Sears 315.10924 - page 5
OPERATION FEATURES Features include easily operated bevel cut and depth of cut adjustment mechanisms; directed air flow for keeping line of cut clear; and blade wrench storage. Before attempting to use your saw, familiarize yourself with all operating features (See Figure 1) and safety requirements. SWITCH Your saw is equipped with a "lock-off ...
-
Sears 315.10924 - page 6
OPERATION TO ASSEMBLE BLADE 1. UNPLUG YOUR SAW. 2. Remove blade wrench from storage area, See Figure 2, 3. Position your saw on end of motor housing and remove blade screw. NOTE: Turn blade screw counterclockwise to remove. 4. Remove spring washer and "D" washer. . , , . Fit saw blade inside blade guard and onto spindle. NOTE: The saw tee ...
-
Sears 315.10924 - page 7
OPERATION BLADE GUARD SYSTEM The lower blade guard attached to your circular saw is there for your protection and safety. It should never be altered for any reason. If it becomes damag- ed, do not operate your saw until the damage has been repaired or replaced. Always leave guard in operating position when using your saw. When sawing through ' ...
-
Sears 315.10924 - page 8
OPERATION TO LESSEN THE CHANCE OF KICKBACK (Cont'd.) . . Make straight cuts. Always use a straight edge guide when rip cutting. This helps prevent twisting the blade in the cut. Always use clean, sharp, and properly .set blades. Never make cuts with dull blades. . To avoid pinching the blade, support the work properly before beginning a cut. T ...
-
Sears 315.10924 - page 9
OPERATION STARTING A CUT (Cont'd) TO HELP MAINTAIN CONTROL: 1. Always support your work near the cut. 2. Support your work so the cut will be on your right. 3. Clamp your work so it will not move during the cut. Place your work with its good side down. NOTE: The good side is the side on which appearance is impor- tant. Before beginning a cut, ...
-
Sears 315.10924 - page 10
OPERATION TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer edge of the notch in the saw base as shown in figure 12. Since the thickness of blades vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut. N ...
-
Sears 315.10924 - page 11
OPERATION TO POCKET CUT (Cont'd.) After you complete your cut release the trigger and allow the blade to come to a complete stop. DO NOT REMOVE YOUR SAW FROM WORKPIECE WHILE THE BLADE IS MOVING. Corners may then be cleaned out with a hand saw or sabre saw. TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between ...
-
Sears 315.10924 - page 12
MAINTENANUI= WHEN SERVICING USE ONLY IDENTICAL REPL'/_CEMENT PARTS POWER CORD OR SWITCH REPLACEMENT 1. UNPLUG YOUR SAW. 2. Remove screws and wing nut securing handle cover. See Figure 17. 3. Carefully lift handle cover away from tool. 4. Note the locations of all lead wiring inside the handle and how each connection has been made. IMPORTANT: W ...
-
Sears 315.10924 - page 13
MAI NTENANCE (Cont'd.) TO CLEAN SAWDUST FROM LOWER BLADE GUARD TO REASSEMBLE See Figure 18. Periodically sawdust will accumulate behind the lower blade guard causing it to be clogged. This clogging could prevent guard from moving freely and readily returning to the down position after use. 1. UNPLUG YOUR SAW. 2. Remove saw blade from your saw. ...
-
Sears 315.10924 - page 14
...
-
Sears 315.10924 - page 15
...
-
Sears 315.10924 - page 16
OWNERS MANUAL SERVICE MODEL NO. 315.109240 HOW TO ORDER REPAIR PARTS 7-1/4 INCH CIRCULAR SAW DOUBLE INSULATED Now that you have purchased your Circular Saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or vis ...
¿Tienes una pregunta acerca de Sears 315.10924?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 315.10924, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 315.10924 probablemente compartirá una forma de solucionarlo.