-
Profile 400MSX - page 1
MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Ma nual 400MSX 600MSX ...
-
Profile 400MSX - page 2
I NTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an exi sting system or including your California amplifier in a new system, you are certain to notice immediate performance be ...
-
Profile 400MSX - page 3
2 S AFETY PRECAUTIONS Fuse amplifier's power wire at the battery . Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not th ...
-
Profile 400MSX - page 4
F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the ...
-
Profile 400MSX - page 5
Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head unit to save current consumption. This control also operates the reset circuit for the amplifier's protecti ...
-
Profile 400MSX - page 6
M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in whic ...
-
Profile 400MSX - page 7
Speaker Output Fuse REM GND B+ CAR BATTERY +12V CAR BATTERY +12V - - + + Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using a 4 to 8 gauge power wire for your connections depending on the amplifier ...
-
Profile 400MSX - page 8
Left Right POWER PROTECTION Hi-Level Input L- R- L+ R+ Bass Boost 0 12 Min Max Input LP X-over 40 130 85 Level Connect the output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run ...
-
Profile 400MSX - page 9
Left Right POWER PROTECTION Hi-Level Input L- R- L+ R+ Bass Boost 0 12 Min Max Input LP X-over 40 130 85 Level If a low level RCA signal source is not available, you may still wire the amplifier with high-level or speaker level outputs from your head unit. However, only speaker leads from a "floating ground" system may be used (see diagra ...
-
Profile 400MSX - page 10
Speaker Output Fuse REM GND B+ Speaker Output Fuse REM GND B+ Make the speaker connections using speaker wire that is at least 10 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the posit ...
-
Profile 400MSX - page 11
Bass Boost 0 12 The amplifier is equipped with a built-in variable low -pass crossover network allowing you to select the desired crossover point for your subwoofers. Please refer to speaker manufactures recommended crossover point. LP X-over 40 130 85 You can add up to 12dB bass boost by increasing the Bass Boost control. Select the crossover poin ...
-
Profile 400MSX - page 12
T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal pro ...
-
Profile 400MSX - page 13
S PECIFICATIONS Due to continuing product improvements, specification to change without notice. 12 400MSX 1 x 400W 1 x 200W 1 x 600W 1 x 300W <0.07% 10Hz ~ 94Hz (at-1dB) >105dB 200mV ~ 8V 16K Ohms 100 Ohms 2 ~ 8 Ohms Low Pass 40Hz ~ 130Hz (at-3dB) 0dB ~ 12dB 250 4 Gauge 6 Gauge 2 x 20A 133 2 / " x 9 / "x 11 / " 444 Max Power @ ...
-
Profile 400MSX - page 14
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy ...
-
Profile 400MSX - page 15
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5 ...
-
Profile 400MSX - page 16
PROFILE CONSUMER ELECTRONICS, INC. 1 5060 SHOEMAKER AVE SANTA FE SPRINGS , CA 90 670 TEL: ( 562 ) 404 - 9393 FAX: ( 562 ) 404 - 9433 WWW.PROFILEUSA.COM By ...
¿Tienes una pregunta acerca de Profile 400MSX?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Profile 400MSX, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Profile 400MSX probablemente compartirá una forma de solucionarlo.