-
Bissell 10N6-F - page 1
2 Thank Y ou USER'S GUIDE 10N6-F SERIES 220-240V Safety Instructions Product View Assembly Operations Maintenance and Care T roubleshooting Replacement Parts 3 4 5 6-8 8-13 13-14 14 Accessories W arranty Consumer Services 14 15 16 ...
-
Bissell 10N6-F - page 2
www .bissell.com T hanks for buying a BISSELL Pet Hair Eraser™ vacuum We’re glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL vacuum is well made, and we back it with a limited one year warranty. We also stand behind it wi ...
-
Bissell 10N6-F - page 3
www .bissell.com I MPOR T ANT SAFETY INSTRUCTIONS 3 When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT V ACUUM. W ARNING: To reduce the risk of f i r e , electric shock, or injury: ■ Do not use outdoors or on wet surfaces. ■ Do not leave machine when ...
-
Bissell 10N6-F - page 4
www .bissell.com 4 P roduct view CAUTION: Do not plug in your vacuum until you are familiar with all instructions and operating procedures. Handle Power Switch Easy Empty ™ Dirt Container Headlight Height Adjustment Knob Wide Cleaning Foot Foot Window W ashable Pre-Motor Filter Carr y Handle Lock ‘n Seal ™ Lever Post-Motor HEP A Media Filter* ...
-
Bissell 10N6-F - page 5
1. www .bissell.com A ssembly The only tool you’ll need to assemble your vacuum cleaner is a Phillips screwdriver . Attach handle to vacuum 1. Locate the handle and cord wrap. Remove the screw packet taped to the handle. 2. Stand the vacuum upright and from the rear of the unit, slide the base of the handle firmly into the grooves at the top of t ...
-
Bissell 10N6-F - page 6
www .bissell.com O perations 6 Power switch The Power Switch is located on the left side of the vacuum. Push the rocker switch “ON” (I) to vacuum, and “OFF” (O) when cleaning is complete. Handle positions Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three clean ...
-
Bissell 10N6-F - page 7
www .bissell.com 7 O perations Special on-board tools Y our vacuum is not only a power ful carpet and rug cleaner , it’ s also a versatile above floor vacuum cleaner when you select one of the special tools. 1. Raise the handle to the upright position. 2. Grasp the hose wand handle to separate from hose wand base. 3. Attach tools by firmly pushin ...
-
Bissell 10N6-F - page 8
www .bissell.com O perations 8 Power cord usage 1. T o use your vacuum, remove the cord and plug it into an electrical outlet. For your convenience, there is a quick release cord wrap for easy cord removal. There is also a cord clip that is part of the upper cord wrap where you can attach the cord when vacuuming. 2. When you are finished cleaning, ...
-
Bissell 10N6-F - page 9
www .bissell.com 9 M aintenance and care Emptying the dirt container The dirt container should to be emptied before the dirt reaches the “Full” line on the container . 1. Unplug the vacuum from electrical outlet. 2. Slide the Lock ‘n Seal Lever to the “Unlock” position. 3. Grasp handle and pull the dirt container straight out to remove fr ...
-
Bissell 10N6-F - page 10
www .bissell.com M aintenance and care 10 Y ou should check your vacuum cleaner ’ s rotating floor brush and drive belt regu - larly for wear or damage. Y ou should also clean the brush and brush ends of strings, hair and carpet fibers. This type of debris can wrap around the brush and hamper its ability to effectively clean your carpet. Also rem ...
-
Bissell 10N6-F - page 11
www .bissell.com 11 M aintenance and care Replace drive belt continued 3. Place new drive belt over motor pulley and loop other end over rotating floor brush in the space between the bristles. NO TE : It is impor tant that you use only genuine BISSELL replacement belts. Generic belts may not meet the exact specifications required to keep your vacuu ...
-
Bissell 10N6-F - page 12
www .bissell.com M aintenance and care 12 3. Remove the brush from the belt and clean debris. 4. Replace the brush inside the belt and place ends into slots on sides as shown. 5. Reposition top cover making sure to line up inside tab at the front with the open- ing on the cover . T wist collar until open- ing is at the bottom to lock into place. Cl ...
-
Bissell 10N6-F - page 13
www .bissell.com 13 M aintenance and care T roubleshooting V acuum cleaner won’ t run Possible causes Remedies 1. Vacuum cleaner is not plugged in 1. Check electrical plug 2. D ama ged powe r co rd 2. Replace as necessary by an authorized service representative. V acuum cleaner and tools won’ t pick up dir t Possible causes Remedies 1. Incorrec ...
-
Bissell 10N6-F - page 14
www .bissell.com T roubleshooting R eplacement parts A ccessories 14 Item Part No. Part Name 1 303-1120 Style 7/9/10/12/14 Drive Belt (2-Pack) 2 203-1603 Headlight Bulb 3 203-1283 Wide W indow Foot Brush Roll (gray) 4 203-1073 Style 7/8/14 Pre-Motor Foam Filter 5 203-6608 Style 8/14 Post-Motor HEP A Media Filter* Item Part No. Part Name 1 203-1056 ...
-
Bissell 10N6-F - page 15
www .bissell.com 15 W arranty - BISSELL Pet Hair Eraser ™ V acuum * The filter media, not the vacuum as a whole, complies with the IEST -RP-CC001.5 HEP A Standard. This warranty gives you specific legal rights, and you may also have other rights which may var y from countr y to countr y . If you need additional instruction regarding this warranty ...
-
Bissell 10N6-F - page 16
©2012 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 110-4512 Rev 1/12 Visit our website at: www .bissell.com B ISSELL consumer services www .bissell.com 16 If your BISSELL product should require service: Call BISSELL Consumer Ser vices at the numbers below and we will give you the location of a BISS ...
¿Tienes una pregunta acerca de Bissell 10N6-F?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Bissell 10N6-F, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Bissell 10N6-F probablemente compartirá una forma de solucionarlo.