-
Haier HSU-12RK03/R2(SDB) - page 1
Please read this operation manual before using the air conditioner . 0010532977 SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL Keep this operation manual for future reference. HSU-09RK03/R2(SDB) Contents 2 3 11 CAUTIONS P ARTS AND FUNCTIONS OPERA TION TROUBLE SHOOTING HSU-12RK03/R2(SDB) HSU-09RS03/R2(SDB) HSU-12RS03/R2(SDB) 12 ...
-
Haier HSU-12RK03/R2(SDB) - page 2
Outdoor Unit Parts and Functions Indoor Unit OUTLET INLET CONNECTING PIPING DRAIN HOSE Remote controller (If the unit which you purchased has healthy TIMER OFF display TIMER ON display SLEEP display If not,please ignore.) When receiving the remote control signal, display the set ti ...
-
Haier HSU-12RK03/R2(SDB) - page 3
1 2 3 Remove the battery cover; Load the batteries as illustrated. 2 R-03 batteries,resetting key(cylinder); Be sure that the loading is in line with the " + "/"-"; Load the battery,then put on the cover again. Loading of the battery Hint: Clock set Operation The distance between the signal transmission head and the receiver ...
-
Haier HSU-12RK03/R2(SDB) - page 4
SMART Operation SMART ƽ SMART FRESH ƽ SMART Defrost ƽ SMART FAN SPEED ƽ SMART FAN HEALTH ƽ SMART SOFT Under the cooling, heating and dehumidifying mode, press the smart key to enter the smart function. When the smart function is running, press the “cooling” “heating” or “dehumidifying” key to switch to the other mode ...
-
Haier HSU-12RK03/R2(SDB) - page 5
Operation SMART Every time the button is pressed, temp. setting o C. Every time the button is pressed, temp. setting o C. Unit will start running to reach the temp.setting on LCD. 1 2 Press FAN SPEED button. For each press, fan speed changes as follows: Unit will run at selected fan speed. AM Select TEMP .setting F AN Operation Press TEMP.setting P ...
-
Haier HSU-12RK03/R2(SDB) - page 6
HEALTH Operation HEALTH AIRFLOW Operation Note: 1.After setting the health airflow function, the position of inlet 2.In heating, it is better to select the mode. 3.In cooling, it is better to select the mode. under the high air humidity , a phenomenon falling drips of 5.Select the appropriate fan direction according to the actual Operation SMART Th ...
-
Haier HSU-12RK03/R2(SDB) - page 7
POWER/SOFT Operation To cancel TIMER mode Just press CANCEL button several times until TIMER let unit start or stop automatically a following times:Before you wake up in the morning,or get back from outside or after TIMER Operation SMART AUTO POWER SOFT displayed Air conditioner starts For each press, is Press POWER button again, disappears,the ope ...
-
Haier HSU-12RK03/R2(SDB) - page 8
Before going to bed,you can simply press the SLEEP button and unit will operate in SLEEP mode and bring Comfortable SLEEP you a sound sleep. Press SLEEP Operation Mode 1 hours after SLEEP mode O C SLEEP operation starts SLEEP operation stops 1 hr Rises 1 O C Rises 1 O C Unit stop In COOL, DRY mode 1 hr 1 hours after SLEEP mode starts,temp will beco ...
-
Haier HSU-12RK03/R2(SDB) - page 9
iFP Operation ECO Operation The power saving function only works under the cooling, heating or dehumidifying mode, after the power saving function is set, press the sharp, mute, sleep, or smart key to exit the power saving function. and automatically control the switch of the compressor, which may be inconsistent with the user’s setting. The powe ...
-
Haier HSU-12RK03/R2(SDB) - page 10
FRESH Operation Exhaust the vitiated air from the room, and inhale fresh air. (This function is unavailable on some models.) Emergency operation and test operation Pi Pi Pi displayed on the remote controller and and the change-for-fresh-air function For twice press , the display " " disappears and the change-for-fresh- air function operat ...
-
Haier HSU-12RK03/R2(SDB) - page 11
power supply cord and so on. 2. Do not install in the place where there is any possibility of inflammable gas leakage around the unit. 3.Do not get the unit exposed to vapor or oil steam. Cautions WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause W ...
-
Haier HSU-12RK03/R2(SDB) - page 12
Trouble shooting Normal Performance inspection Noise is heard Phenomenon Cause or check points The system immediately . Smells are gen erated . Mist or steam are Multiple check Poor cooling When unit is stopped, it won't restart elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit During un ...
¿Tienes una pregunta acerca de Haier HSU-12RK03/R2(SDB)?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Haier HSU-12RK03/R2(SDB), haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Haier HSU-12RK03/R2(SDB) probablemente compartirá una forma de solucionarlo.