-
Canon INDEX 4602 - page 1
INDeX 4602 IP Telephone Installation Manual 38DHB0002UKCQ – Issue 2 (11/06/2003) ...
-
Canon INDEX 4602 - page 2
Page 2 - Contents Contents Introduction ........................................................................................................... 3 Use of this Manual ................................................................................................................................. 3 Switch Requ irements ............................ ...
-
Canon INDEX 4602 - page 3
Introduction Use of this Manual - Page 3 Introduction Supported by INPC Level 3.3 and I NDeX 10.1+ software, the 4602 IP Telephone uses Internet Protocol (IP) technology with Ethernet interfaces. The 4602 IP Telephones support DHC P and TFTP over IPv4/UDP which enhance the administration and servicing of the phones. These pho nes can use DHCP to ob ...
-
Canon INDEX 4602 - page 4
Page 4 - INDeX Setup Installation Procedure Installation Procedure Prior to installation of the INDeX 4602 IP Telephone on a user's networked PC, ensure that both the INDeX and IP NC have been configured as follows: INDeX Setup Log on to the INDeX and open the Administration menu and perform the following: 1. Open Directory | General Setup | A ...
-
Canon INDEX 4602 - page 5
Installation Procedure IPNC Setup - Page 5 Installation Requirements To install a 4602 IP Telephone onto INDeX, the following items are required: • Power Socket: A switched 110-240V AC, 50-60Hz, 250-500mA supply socket is required for each 4602 IP telephone. • LAN Socket: A 10/100Mbps RJ45 Ether net LAN connection point is required for each IP ...
-
Canon INDEX 4602 - page 6
Page 6 - IPNC Setup Installation Procedure Dynamic Address Process This is the recommended method to assign IP and telephony settings to the 4602 IP telephone. DHCP Installation Preparation This installation process uses the INDeX/INPC as a DHCP Server and H323 Gatekeeper to assign IP and telephony setti ngs to the 4602 IP telephone. It also assume ...
-
Canon INDEX 4602 - page 7
Installation Procedure IPNC Setup - Page 7 DHCP Phone Installation 1. Connect the longer LAN cable from the network LAN socket to the power unit's LINE socket. Note: The 400B2 Power Adaptor used for providing power for 4602 IP Telephones is not compatible with the sockets on INDeX units. We therefore advise against the direct connection of the ...
-
Canon INDEX 4602 - page 8
Page 8 - IPNC Setup Installation Procedure Static Addressing Pre-Installation Checklist Before performing static addressing on t he 4602 IP Telephone, verify that have the values for the following parameters. Failure to do so may cause errors during data entry, which will prevent t he telephone from working and may have a negative impact on your ne ...
-
Canon INDEX 4602 - page 9
Installation Procedure IPNC Setup - Page 9 3. Enter the IP address for the gatekeeper followed by the # button. The following message is displayed: CallsSvPort=nnnn New=_ where “nnnnn” is the value of the Management Complex (call server/gatekeeper) transport laye r port number, a value between 0 and 65535. 4. Enter the appropriate value for the ...
-
Canon INDEX 4602 - page 10
Page 10 - IPNC Setup Installation Procedure 8. Press the 1 or 0 button to turn 802.1Q on or off respectively. The display is updated to show the current status of 802.1Q. Press the # button to continue the procedure without changing the displayed status of 802.1Q. The following text is displayed left-j ustified at the top of the display: VLAN ID=dd ...
-
Canon INDEX 4602 - page 11
Installation Procedure IPNC Setup - Page 11 QoS Option Setting 3 Administering QoS options is not mandat ory, but it is highly recommended. The 802.1Q must be switched on for the follo wing procedure to be applicable (see step 8 of Static Addressing Installation). Use the following procedure to set Q uality of Service (QOS) options. 1. While the ph ...
-
Canon INDEX 4602 - page 12
Creating the DHCP Scope:Page 1 2 - Contents Creating the DHCP Scope: The creation of DHCP Scopes should only be performed by System Administrators with Ad ministrator rights. DHCP scopes are configured using the DHCP MMC snap-in as follows: 1. Start the DHCP MMC snap-in (Star t/Programs/Administrative Tools/DHCP) 2. Right click on the server and se ...
-
Canon INDEX 4602 - page 13
Creating the DHCP Scope: IPNC Setup - Page 13 7. You can now configure the lease time for the address. Setting too large will mean you will lose the use of addresses if the client machine is inactive for long periods of time, too short and you will generate unnecessary traffic renewing the address. The default 8 days is fine. Click Next 8. The wiza ...
-
Canon INDEX 4602 - page 14
Page 14 - Adding the 4602 IP Telephone Option (1 76): Creating the DHCP Scope: Adding the 4602 IP Telephone Option (176): 1. Right click on the server. 2. Select Set Predefined Op tions from the pop-up menu. 3. Select Add and, from the Data type pull down menu, select String: 4. Enter the following information: Name: 46xxOptions Data type: String C ...
-
Canon INDEX 4602 - page 15
Creating the DHCP Scope: Adding the 4 602 IP Telephone Option (176 ): - Page 15 5. In the string value fi eld enter the following: MCIPADD=xxx.xxx.xxx.xxx,MCPORT=1719,TFTPSRVR=yyy.yyy.yyy .yyy,TFTPDIR=z Where: xxx.xxx.xxx.xxx = IP of the INDeX/IPNC yyy.yyy.yyy.yyy = TFTP Server IP Address (of the PC running the INDeX/IPNC Manager application) z = t ...
-
Canon INDEX 4602 - page 16
Performance figures and data quoted in this document are typical, and must be specifically confirmed in writing by Avaya before they become applicable to any particula r order or contract. The company reserves the right to make altera tions or amendments to the detailed specifications at its discretion. T he publication of information in this docum ...
¿Tienes una pregunta acerca de Canon INDEX 4602?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Canon INDEX 4602, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Canon INDEX 4602 probablemente compartirá una forma de solucionarlo.