-
Grindmaster P200E - page 1
P200E Shuttle & RAPS200E Airpot/Shuttle Br e w er Series Operation and Instruction Manual Installation W ARNING: ELECTRIC SHOCK HAZARD! INST ALLA TION OF THIS APPLIANCE SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL ONL Y . IMPROPER INST ALLA TION COULD RESUL T IN ELECTROCUTION. See rough-in drawings in this manual for dimensions and locati ...
-
Grindmaster P200E - page 2
...
-
Grindmaster P200E - page 3
Page 2 P200/RAPS200 Brewers Installation (con't.) Electric hook-up 1) The electric ratings for your brewer are printed on its nameplate. T ypical electric ratings are: 120V , 1.65 kW , 15 Amp, 1 phase. 2) The brewer should be connected to its own circuit with a fused disconnect switch or a circuit breaker near the brewer . 3) Electrical connec ...
-
Grindmaster P200E - page 4
Page 3 Operation CAUTION: HOT LIQUID HAZARD W A TER USED FOR BREWING COFFEE IS VER Y HOT . USE CAUTION WHEN BREWING , POURING , OR TRANSPORTING COFFEE. ACCIDENT AL SPILLS MA Y RESUL T IN SEVERE BURNS. 1) Place an empty , warm Shuttle under the brew head. T urn on the warmer once a Shuttle is in place, or place an empty 1.9L to 3.0L airpot under the ...
-
Grindmaster P200E - page 5
Page 4 Adjustment s W ARNING: ELECTRIC SHOCK HAZARD DANGEROUS ELECTRIC VOL T AGES ARE PRESENT NEAR ADJUST ABLE COMPONENTS. ALL ADJUSTMENTS SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL ONL Y . All adjustable component s are located under the top cover . T o access these parts: 1) Unplug the brewer . 2) Remove the screw fastening the top cover ...
-
Grindmaster P200E - page 6
Page 5 Thermost at Adjustment The thermostat controls the water temperature in the t ank. Factory setting is 195 degrees F . This is the ideal temperature for brewing coffee. W ater should never boil in the tank. If water is boiling in the tank, adjust the temperature appropriately . S tandard Mechanical Thermostat: 1) Shut off power and unplug bre ...
-
Grindmaster P200E - page 7
Page 6 Weekly or Bi-W eekly , Depending on Use (P200 Only): 1) Fill Shuttle with one gallon of hot water . 2) Pour the recommended concentration of urn cleaner into the Shuttle liners (Excessive amounts of cleaner will attack the st ainless steel). Urn cleaners that have been used successfully: DIP-IT , manufactured by Economics Laboratories, Inc. ...
-
Grindmaster P200E - page 8
Page 7 P200/RAPS200 Brewers T o Drain The Water T ank CAUTION: HOT LIQUIDS / BURN HAZARD W A TER IN T ANK IS VER Y HOT . USE CAUTION WHEN DRAINING T ANK. ACCIDENT AL SPILLS MA Y RESUL T IN SEVERE BURNS. 1) Shut off power to brewer . 2) Remove the top panel. 3) Remove the warmer shelf. 4) Pinch or clamp the tube from fill valve to tank (near t ank e ...
-
Grindmaster P200E - page 9
Page 8 T roubleshooting: Filling, Heating, and Brewing Overfilling watert ank even when power is off. Fill valve not sealing properly . Fill valve installed backwards. W ater entering t ank continuously , usually slowly . Disassemble valve and clean out dirt. V alve may need new plunger if seal is worn. Problem Possible Cause Service Check Remedy F ...
-
Grindmaster P200E - page 10
Page 9 T roubleshooting: Filling, Heating, and Brewing (con’t.) T ank does not heat. Thermostat faulty or out of calibration. Heater faulty . Make sure thermostat is turned on. Check resistance across elements with wires disconnected. Recalibrate thermostat. If no reme- dy or thermostat does not cycle, replace thermostat. If resistance is much di ...
-
Grindmaster P200E - page 11
Page 10 T roubleshooting: Filling, Heating, and Brewing (con’t.) Brewing Problems The brewing system consists of the following component s: • St art and Stop switches , located on the front control panel. • Brew Timer , located in the top control section under the top cover . Brew volume too large or too small. T imer out of ad- justment. Pre ...
-
Grindmaster P200E - page 12
Page 1 1 P200/RAPS200 Brewers Exploded V iew for the P200-E ITEM DESCRIPTION P ART # ...
-
Grindmaster P200E - page 13
Page 12 P200/RAPS200 Brewers Exploded V iew for the P200 (G version only) ITEM DESCRIPTION P ART # ...
-
Grindmaster P200E - page 14
Page 13 P200/RAPS200 Brewers Exploded V iew for the RAPS200-E ITEM DESCRIPTION P ART # ...
-
Grindmaster P200E - page 15
Page 14 P200/RAPS200 Brewers Exploded V iew for the RAPS200 (G version only) ITEM DESCRIPTION P ART # ...
-
Grindmaster P200E - page 16
Page 15 P200/RAPS200 Brewers Rough-In Drawing for the P200-E ...
-
Grindmaster P200E - page 17
Page 16 P200/RAPS200 Brewers Rough-In Drawing for the RAPS200-E ...
-
Grindmaster P200E - page 18
Page 17 P200/RAPS200 Brewers Wiring Diagram for P200-E/RAPS200-E ...
-
Grindmaster P200E - page 19
...
-
Grindmaster P200E - page 20
W ARRANTY for P200/RAPS200 Series GENERAL W ARRANTY INFORMA TION Grindmaster maintains the highest st andard of quality control in the manufacturing of American Metal W are products. W e use the finest component s and materials, and employ quality engineering standards and tests. The P200E Brewer is warranted for a period of one year from date of s ...
¿Tienes una pregunta acerca de Grindmaster P200E?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Grindmaster P200E, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Grindmaster P200E probablemente compartirá una forma de solucionarlo.