-
Harbor Freight Tools 45338 - page 1
HAMMER DRILL - 1/2 INCH HAMMER DRILL - 1/2 INCH HAMMER DRILL - 1/2 INCH HAMMER DRILL - 1/2 INCH HAMMER DRILL - 1/2 INCH V V V V V ARIABLE SPEED - REVERSIBLE ARIABLE SPEED - REVERSIBLE ARIABLE SPEED - REVERSIBLE ARIABLE SPEED - REVERSIBLE ARIABLE SPEED - REVERSIBLE ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 MISSION OAKS BL VD ., CAMARILLO , CA 9301 ...
-
Harbor Freight Tools 45338 - page 2
Page 2 SKU 45338 SPECIFICA TIONS I t em Desc r i pt i on Pow er C onsum pt i on 120 V AC , 6 0 Hz, si n gl e ph a se, 6. 3 am ps ( l oad ) , 750 w at t s Mo t o r D oubl e i nsul at e d C huck Cap aci t y 3/ 64 t o 1/ 2 i nch, pl us key chuck C huck Thr ead 1/ 2" - 20 U N F Spe ed 0 ~ 2800 R PM (no l oad); 0 ~ 42 , 00 0 BP M Sw i tch El ect ro ...
-
Harbor Freight Tools 45338 - page 3
Page 3 SKU 45338 Electrical Safety 4. A void body contact with g rounded surf aces such as pipes, radiators, ranges , and refrigerators. There is an increased r isk of electr ic shock if y our body is grounded. 5. Do not e xpose power tools to rain or wet conditions . W ater enter ing a power tool will increase the risk of electr ic shock. 6. Groun ...
-
Harbor Freight Tools 45338 - page 4
Page 4 SKU 45338 14. Do not ov erreach. Keep proper f ooting and balance at all times. Proper f ooting and balance enables better control of the po wer tool in unexpected situations . 15. Use saf ety equipment. Always w ear e ye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used f or appropr iate conditions. ...
-
Harbor Freight Tools 45338 - page 5
Page 5 SKU 45338 SPECIFIC SAFETY RULES FOR THE HAMMER DRILL 1. Hold tool b y insulated gr ipping surfaces when perf or ming an operation where the cutting tools ma y contact hidden wir ing or its own cord. Contact with a ”live” wire will make e xposed metal par ts of the tool “live” and shock the operator . 2. Maintain labels and nameplates ...
-
Harbor Freight Tools 45338 - page 6
Page 6 SKU 45338 GROUNDING W ARNING! Impr ope rly connecting the gr ounding w ire can result in t he risk of electri c shoc k. Check wit h a qualfi f ied elect rici an if y ou are in doubt as t o whether t he outlet is pr ope rl y grounded. Do not modify the power cord plug pr o v i ded with the tool. Never remo ve the grounding pr ong from the plu ...
-
Harbor Freight Tools 45338 - page 7
Page 7 SKU 45338 EXTENSION CORDS 1. Grounded tools require a three wire e xtension cord. Double Insulated tools (like this one) can use either a two or three wire e xtension cord. 2. As the distance from the supply outlet increases, y ou must use a heavier gauge e xtension cord. Using extension cords with inadequately siz ed wire causes a ser ious ...
-
Harbor Freight Tools 45338 - page 8
Page 8 SKU 45338 SYMBOLOGY T able B UNP A CKING When unpacking, chec k to make sure that all the par ts are included. See Figure C. Also ref er to the Assembly section, and the Assemb ly Drawing and P ar ts List at the end of this manual. Figure C If any par ts are missing or broken, please call Harbor F reight T ools at the number on the cov er of ...
-
Harbor Freight Tools 45338 - page 9
Page 9 SKU 45338 ASSEMBL Y INSTR UCTIONS 1. Inser t the Auxiliar y Handle (501) over the Housing (29) until it rests behind the Chuc k (2). When required for e xact depth dr illing, inser t the Depth Gauge (502) into the A uxiliar y Handle clamp. See Figure D belo w . 2. T urn the Forw ard Handle for left or right-handed use, then securely tighten ...
-
Harbor Freight Tools 45338 - page 10
Page 10 SKU 45338 Figure E 3. Adjust the V ariable Speed Scre w f or the desired (maximum) speed action when the Switch is pressed. 4. F or precision depth dr illing, loosen the Wing Nut securing the Auxiliar y Handle (501), and slide the Depth Gauge (502) down, gauging the depth from the bit tip . Retighten the Wing Nut again. 5. V erify that the ...
-
Harbor Freight Tools 45338 - page 11
Page 11 SKU 45338 INSPECTION, MAINTENANCE, AND CLEANING Caution! Make sure the P ower Switc h of the Hammer Drill is in its “OFF” position and that the tool is unplugged fr om its electrical outlet before perf orming any inspec- tion, maintenance, or cleaning procedures. 1 . Before each use, inspect the general condition of the Hammer Drill. Ch ...
-
Harbor Freight Tools 45338 - page 12
Page 12 SKU 45338 NO TE : Some par ts are listed and shown f or illustra- tion pur poses only and are not a vailab le individually as replacement par ts. PARTS LIST Item No. Description Qty. 1. Screw, M6 x25 1 2. Chuck 1 3. Chuck K ey 1 4. Spind le 1 5. Steel Ba ll , 3 1 6. Circle Se al 1 7. Ball Bea ring 1 8. Spring 1 9. Gear, Lar ge 1 10. Needle ...
-
Harbor Freight Tools 45338 - page 13
Page 13 SKU 45338 ASSEMBL Y DRA WING ...
¿Tienes una pregunta acerca de Harbor Freight Tools 45338?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 45338, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 45338 probablemente compartirá una forma de solucionarlo.