-
Pelco C1987M - page 1
® Installa tion/Oper a tion MC3700 Series Monoc hr ome Camera C1987M (6/02) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150 International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120 ...
-
Pelco C1987M - page 2
[ 2 ] Pelco Manual C1987M (6/02) ...
-
Pelco C1987M - page 3
Pelco Manual C1987M (6/02) [ 3 ] CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS .............................................................................................. ....... 4 Regulatory Notices ............................................................................................................. ...................................... ...
-
Pelco C1987M - page 4
[ 4 ] Pelco Manual C1987M (6/02) IMPORT ANT SAFEGU ARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should be done only by qualified service and installation personnel. 2. Installation shall be done in accordance with all local and national electrical and mecha ...
-
Pelco C1987M - page 5
Pelco Manual C1987M (6/02) [ 5 ] DESCRIPTION The MC3700 Series monochrome video camera is compact, with a 1/3-inch CCD imager . The camera has a direct drive/auto iris lens connector and adjustable back focus, and accepts C and CS lenses. Models MC3700S-2 Standard resolution, 380 TV lines, SuperHAD™ CCD, 0.08 lux @ 50 IRE, f1.2, EIA MC3700S-2X St ...
-
Pelco C1987M - page 6
[ 6 ] Pelco Manual C1987M (6/02) CAMERA LA Y OUT BACK FOCUS ADJUSTMENT RING BNC VIDEO CONNECTOR LENS CONNECTOR LED MOUNT ADAPTER PHASE ADJUSTMENT LENS LEVEL ADJUSTMENT POWER CONNECTOR BACK FOCUS ADJUSTMENT LOCKING SCREW COSMETIC TRIM RING DIP SWITCHES (COVER REMOVED) NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance ...
-
Pelco C1987M - page 7
Pelco Manual C1987M (6/02) [ 7 ] PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS 1 Control coil negative (-) Not used 2 Control coil positive (+) Lens positive supply 3D rive coil positive (+) Video drive signal 4D rive coil negative (-) Ground Figure 2. AID/AIV Lens Connector Camera Mounting Use a standard 1/4-20 screw (provided) with a max ...
-
Pelco C1987M - page 8
[ 8 ] Pelco Manual C1987M (6/02) POWER AND VIDEO CONNECTIONS MC3700 Series camera is designed to operate from a 12 VDC or 24 V AC power supply . The power supply con- nections are shown in Figure 4. The LED on the back panel of the camera indicates that power is connected. Use only a Class 2 isolated power supply . Power consumption is less than 5 ...
-
Pelco C1987M - page 9
Pelco Manual C1987M (6/02) [ 9 ] AC Operation Only – If you are wiring more than one camera to the same transformer , connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras. Failure to connect all of the cameras the same way will cause the cam ...
-
Pelco C1987M - page 10
[ 10 ] Pelco Manual C1987M (6/02) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak). Switch the AGC ON ...
-
Pelco C1987M - page 11
Pelco Manual C1987M (6/02) [ 11 ] BA CK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring: a. Clockwise - Moves the CCD sensor assembly towards the back ...
-
Pelco C1987M - page 12
[ 12 ] Pelco Manual C1987M (6/02) SWIT CH SETTINGS Figure 6. Switch Settings (Defaults) LL/INT Synchronization Selection – Switch Setting 10 Locks the frame rate to the power supply frequency . Eliminates vertical roll caused by multiple cameras connected to the same switching device. Each camera output is syn- chronized to the frequency of the p ...
-
Pelco C1987M - page 13
Pelco Manual C1987M (6/02) [ 13 ] A GC OFF/A GC ON – Switch Setting 5 Automatically adjusts the image to compensate for low light levels when using fixed or manual iris lenses. AGC (Default setting) - Enables the AGC mode. OFF - Disables the AGC mode. ESC ON/ESC OFF (Electronic Sensitivity Contr ol) – Switch Setting 4 The ESC feature compensate ...
-
Pelco C1987M - page 14
[ 14 ] Pelco Manual C1987M (6/02) CAMERA SYNCHRONIZA TION When using one AC power supply in a multi camera system, a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll adjust the phase control to synchronize (line-lock), the cameras to one another . The synchronization switch (DIP switch 10 ...
-
Pelco C1987M - page 15
Pelco Manual C1987M (6/02) [ 15 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch Synchronization System: AC line lock or internal oscillator Horizontal Resolution: 380 TV lines Iris Control: Electronic/passive Minimum Illumination: 0.08 lux @ 50 IRE, f1.2 Signal-to-Noise Ratio: 52 dB (AGC Off) Gain Control: Automatic Ve rtical Phase: Adjustable 0 ° ...
-
Pelco C1987M - page 16
[ 16 ] Pelco Manual C1987M (6/02) ® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco. ™ Esprit and Camclosure are trademarks of Pelco. ™ HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation. © Copyright 2002, Pelco. All rights reserved. WARRANTY AND RETURN INFORMA TION REVISION HISTOR Y Manual ...
¿Tienes una pregunta acerca de Pelco C1987M?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco C1987M, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco C1987M probablemente compartirá una forma de solucionarlo.