-
Z-Com R2 Extender - page 1
R2 Extender Quick Installation Guide V 1.0 January 2009 Page 1 ...
-
Z-Com R2 Extender - page 2
Copyright Copyright © 2008 all rights reserved. No part of this pu blication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permi ssion of the supplier . About the Inst allation Guide This Install ation Guide is intended to g uide professional i ...
-
Z-Com R2 Extender - page 3
Chapter 1 Introduction Introduction The R2 Extender is a high-perform ance outdoo r-d eployable wireless b ridge that provides wireless connectivity amon g multiple network locations. It support s Base S tation, CPE, PTP and PTMP conne ctivity . Moreover , the R2 Ext ender has a built-in 23dBi planar antenna that can deliver up to a 40Km connection ...
-
Z-Com R2 Extender - page 4
Chapter 2 Prep aration before Inst allation This chapter descri bes safety precautions and produ ct information you have to know and check before installi ng R2 Extend er . Professional Inst allation Required 1. Please seek assist ance from a profes sional inst aller who is well trained in the RF in stallation and knowledgeable in the local regulat ...
-
Z-Com R2 Extender - page 5
Product Package The product p ackage you have received should cont ai n the following items. If any of them are not included or damaged, plea se contact your local vendo r for sup port. R2 Extender with integrated 23dBi antenna × 1 Mounting Kit × 1 P o E I n j e c t o r & P o w e r c o r d × 1 G r o u n d i n g W i r e w / s c r e w × 1 W a ...
-
Z-Com R2 Extender - page 6
10. Woo d Screw × 4 (for Wall Mount) 11. W all/Gyprock Plug × 4 (for Wall Mount) W aterproof RJ-45 Connector Kit 1. Gland × 1 2. Sealing Nut × 1 3. Sealing × 1 Page 6 ...
-
Z-Com R2 Extender - page 7
Chapter 3 System Inst allation Assemble the Mounting Bracket 1. Place the main bracket into the seating and u se a spa nner to fa sten the bracket to the R2 Extender with M5×16 screws ○ 8 and M5 washers ○ 9 provided in the hardware p acket s; 2. Assemble the main bracket by placing articulation pole ○ 2 to the T -form bracket ○ 1 via a M8? ...
-
Z-Com R2 Extender - page 8
2. Fasten two M8×80 screws ○ 4 and washers ○ 5 through the drill holes and mai n bracket with a spanner; 3. Adjust the antenna for appropriate tilt / vertical orient ation. Chapter 3 Hardware Installation Page 8 ...
-
Z-Com R2 Extender - page 9
Connect Up Before installi ng the Ethernet cable with a wate rproof RJ-45 co nne ctor , it is recommended that the Cat-5 RJ-45 coaxial cable be used f or t he bridge to powe r inje ctor connections. 1. T o connect to the hole labeled PoE+Dat a , open the black cover in advance by using a coin or a slotted screwd riv er and then screw in the body of ...
-
Z-Com R2 Extender - page 10
Ground the Wire The R2 Extender is shipped with a grounding wire. The unit m ust be properly grounded to protect against power surges. The grounding point can be found on the bottom of the unit. It is supplied with an appropriat e grounding lug for att achment to the ODU. Power On T o power up the R2 Extender , follow the steps bell ow: 1. Plug a u ...
-
Z-Com R2 Extender - page 11
Make sure PoE is correctl y connected to the RJ-45 port on the R2 Extender lab eled PoE+Data. DO NOT connect to the port labeled “W arning!! No POE” , otherwise the extender will be severely damaged! W arning: Chapter 5 T r ou bleshooting Page 1 1 ...
-
Z-Com R2 Extender - page 12
Chapter 4 Configuration Connect the R2 Extender to a Local Computer If you are configuring the R2 Extender locally (without connecting its powe r injector to a wired LAN), connect a PC to the power injector ’s Et hernet port using a Category 5 Ethernet cable. 1. Assign a st atic IP address to your PC whic h is in the same network se gment with th ...
-
Z-Com R2 Extender - page 13
Note: System ready R2 Extender ’s still initializing Considering convenient configuration, it is recommended to configure lo cal and remote R2 Extender respectively on two computer s. z TTL time may vary depending on the op erating system.. Chapter 5 T r ou bleshooting Page 13 ...
-
Z-Com R2 Extender - page 14
How to Est ablish Wireless Bridge Mode The R2 Extender support s four operating modes, which are Base S tation, CPE, Peer-to-Peer (CSMA) and Peer-to-Peer (TDMA). Normally , Wirele ss Bridge is the typical mode on this u nit. Here we will illustrate how to est ablish wireless b ridge connectivity with R2 Extender . Enter the user name (admin) and p ...
-
Z-Com R2 Extender - page 15
192.168.1.2 and set the IP Subnet Mask on both as 255.255.25 5.0 W arning: Each IP add ress is uni que within a LAN, otherwise IP collision may occur! Open “ Radio ” in “ Wireless ” and you wi ll find the default oper ating mode is Peer-to-Peer (CSMA). Select RF1(WLAN1) or RF 2 (WLAN2) as Bridge to make the following configuration. Here we ...
-
Z-Com R2 Extender - page 16
Login the Web-ba sed interface of remote R2 Extender , open “ About ” in “ System ” and record the wireless MAC address of it, either WLAN 1 or WLAN 2 MAC Address. Login the Web-based interface of local R2 Extender and open “ Peer-to-P eer Setup ” in “ Wireless ”. Select “RF1” , input the WLAN1 or WLAN2 MAC addre ss of the remot ...
-
Z-Com R2 Extender - page 17
W arning: The MAC address on the housing of R2 Extender is the ETH MAC address; therefore it can not be used in Peer-to-Peer links. The IP address of your PC should be in the same network segme nt to the one of bridges. Use ping to check whether the link between the two R2 Extender is OK. R2 Extender B R2 Extender A T o get a better wireless connec ...
-
Z-Com R2 Extender - page 18
in “ Wireless ”. Select RF1 and hit “ Align Antenna ” b utton, an antenna alignment tool will popup. S pecify the T arget RSSI and clic k “ Start ” to begin the antenna alignment. Fix the local antenna and adjust the remote antenna elevation and horizontal directio n. During the adjustme nt, observe “ Current RSSI ” in local R2 Exte ...
-
Z-Com R2 Extender - page 19
Chapter 5 T roubleshooting This chapter provides troubleshooting procedure s for basi c problems with the R2 Extender . Q 1. What if m y R2 Extender fails to connect to the remote one? • Ethernet Link : Check the availability of power to the bridge by observing the LED status on the power inje cto r . - Green: The R2 Extender is connecting to the ...
-
Z-Com R2 Extender - page 20
Chapter 6 T echnical Support Page 20 Chapter 6 Service Information If you have any further trouble using the R2 Ext ender or you would like to require additional support, you may visit our website at www .zcom.com.tw/rpc or you may conta ct us as below for support: Z-Com, Inc. T aiwan Business Center 7F-2, No.9. Prosperity RD. I Science-Based Indus ...
¿Tienes una pregunta acerca de Z-Com R2 Extender?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Z-Com R2 Extender, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Z-Com R2 Extender probablemente compartirá una forma de solucionarlo.