Manual de instrucciones Ohlins SUPERBIKE FG 570

28 de páginas 1.38 mb
Descargar

Pasar a la página of 28

Summary
  • Ohlins SUPERBIKE FG 570 - page 1

    Owners Manual Öhlins Superbike Fr ont Fork FG 570 ...

  • Ohlins SUPERBIKE FG 570 - page 2

    Safety signals Important information concerning safety is distinguished in this manual by the following notations: This Safety alert symbol means: Caution! Y our safety is involved. ! W ARNING! Failure to follow warning instructions could result in severe or fatal injur y to anyone working with, inspecting or using the sus- pension, or to bystander ...

  • Ohlins SUPERBIKE FG 570 - page 3

    Öhlins Fr ont Fork FG 570 This Super Bike front fork is an impr oved version of FG 470 with pressurised damp- ing system. FG 570 is based on 5 years experience from factory r oad racing. The pressurised damping system impr oves the front fork function at high fr equency move- ments. The immediate damping responses improve the tyr e feeling and als ...

  • Ohlins SUPERBIKE FG 570 - page 4

    Adjusters Y our Öhlins super bike fr ont fork is pro- vided with the following external adjusters: • Spring pre-load adjuster • Rebound damping adjuster . • T wo type of compr ession damping adjuster: - Reservoir valve adjuster in the lower part of the fork leg. - Main valve bleed circuit. NOTE! The rebound damping adjuster is located at the ...

  • Ohlins SUPERBIKE FG 570 - page 5

    Setting up your forks Here is some basic guidelines, how to set up your Öhlins front forks. However you must remember that the fr ont forks are just one part of your motorcycle and to get it to work properly , the whole motorcycle has to be set up according to your bikes manual. 1 Put your bike on a front stand and fit the Öhlins front fork. NOTE ...

  • Ohlins SUPERBIKE FG 570 - page 6

    Changing springs 12 17 mm socket 1. Unload the spring pre-load completely by turning the adjustment nut counter clockwise as far as possible. Use a 17 mm wrench or socket. 2. Loosen the screws that hold the fork legs in the upper triple clamps. 3. Remove the T op nut assembly . Use tool 797-01. 4. Remove the top nut assembly from the piston shaft. ...

  • Ohlins SUPERBIKE FG 570 - page 7

    180 0 1st, Circlip 2nd, Seal 3rd, W asher Changing seals 1. Remove the fork legs from the motor cycle. Put the fork legs in upright position for about 5 minutes to allow the oil to settle. 2. Fasten the fork leg in a vice. Use soft jaws. 3. Carry out instructions 1 to 5 in “Changing springs”, page 6. 4. Drain the cylinder tube from oil. 5. Remo ...

  • Ohlins SUPERBIKE FG 570 - page 8

    Dismantling the Forks 1. Remove the fork legs from the motor cycle. Put the fork legs in upright position for about 5 minutes to allow the oil to settle. 2. Fasten the fork leg in a vice. Use soft jaws. 3. Unload the spring pre-load completely by turning the adjustment nut counter clockwise as far as possible. Use a 17 mm wrench or socket. 4. Loose ...

  • Ohlins SUPERBIKE FG 570 - page 9

    ! W ARNING! Releasing high pressure gas from the front fork can be hazardous. Do not perform any kind of service until gas pr essure is com- pletely released. 9. Remove the circlip. 10. Use tool 720-03 to lift up the reservoir end cap. Install the tool 720-02 into the gas piston. 11. Use tool 1797-04 and 1765-03 to unscrew the seal head from the ca ...

  • Ohlins SUPERBIKE FG 570 - page 10

    13. Remove the Piston holder . Use a 14 mm wrench. 14. Remove the T opout spring, the Sleeve, the Spacer and the O-ring. 15. Remove the Seal head. Check the O-ring and the X-ring. Change them if necessary . 16. Remove the needle and change the O-ring if necessary . 17. Drain the cylinder tube from oil. 18. Remove the gas piston in the reservoir , u ...

  • Ohlins SUPERBIKE FG 570 - page 11

    22 23 Upper bushing Lower bushing Heat air gun 22. Remove the outer tube, clean the seal and check the condition. If the seal is in good condition apply some red gr ease (146-01) to it. A damaged seal must be replaced! 23. First remove the cir clip, then the seal and finally the washer . 24. Heat the tube where the bushings ar e posi- tioned. Use a ...

  • Ohlins SUPERBIKE FG 570 - page 12

    Assembly of the forks 1. Use T ool 786-07 to r efit the reservoir tube. Tighten to 45 Nm. 2. Use T ool 786-05 to r efit the inner tube of the fork leg. Tighten to 80 Nm. 3. Put the outer tube standing up on a soft surface, seal side up. Fit the bushings from the seal side of the outer leg. Install first the upper bushing then the lower one. Use ins ...

  • Ohlins SUPERBIKE FG 570 - page 13

    6. Install the piston and the shims on the compression valve. Tighten the 8 mm nut with a torque of 7 Nm. Check the piston ring and the O-rings for damages. Replace if necessary . Install the compression valve assembly into the valve housing. Tighten to 20 Nm. Compression valve assembly: 7. Apply some front fork oil (1311-01) to the inner tube surf ...

  • Ohlins SUPERBIKE FG 570 - page 14

    10. Grip the piston shaft with soft jaws 727-02. Fit the O-ring on the adjustment needle. Apply plenty of red gr ease on the O-ring so that the needle slides easily into the piston shaft. 11. Check the X-ring and O-ring on the seal head. Replace if necessary . Smear plenty of white grease on the X-ring befor e you fit it. Use tool 0715-01 to get th ...

  • Ohlins SUPERBIKE FG 570 - page 15

    CAUTION! The Washers must be positioned correctly (Notice that there is a difference between the compression and the rebound valve). Also make sure to fi t the Wave washer (1149-01) in the correct position (convex side facing piston). NOTE! The right hand fork leg is the rebound leg. The left hand fork leg is the compression leg. 14. Fit the Seal ...

  • Ohlins SUPERBIKE FG 570 - page 16

    ! W ARNING! Use of infl ammable gas for pressurising the soch absorber can be hazardous. Use nitrogen gas (N2) only! 19. Check the gas pressur e stipulated in the spec. card. Dip the needle of the gas tool (1781-01) in red gr ease and insert the nee- dle through the gas filler valve. Char ge with gas to the correct pr essure, according to the spec ...

  • Ohlins SUPERBIKE FG 570 - page 17

    Oil level adjustment Compared with conventional type of fr ont forks, the upside down front forks ar e very sensitive to variations in oil level. Therefor e, adjust the oil level with special care. A change in the fork oil level will not affect the spring force at the beginning of the fork travel, but will have a great ef fect at the end of the tra ...

  • Ohlins SUPERBIKE FG 570 - page 18

    T roubleshooting Below are a few examples of how to adjust for the most common road holding pr ob- lems in Road Racing driving. 1. The front wheel “chatters” entering a corner , the problem goes away , as soon as you let the brakes off, or when you get on the power . • This is caused by the fact that the fork is working too low in the travel ...

  • Ohlins SUPERBIKE FG 570 - page 19

    Guidelines The settings on this pressurised Fr ont Fork are based on what curr ently is being used in Moto GP racing, furthermore the delivery spec is something we like to refer to as a “balanced setting”. This means that the pressur e drop over the bottom valves (base valves) and the top pistons (ø25mm) are matched. In order to avoid an unnec ...

  • Ohlins SUPERBIKE FG 570 - page 20

    Individual adjustments Individual adjustments Below you can find the recommended ad- justment range for the top left compression leg adjuster , with differ ent positions on the bottom base valve. From soft to har d: Base 19 clicks, top 17-20 clicks Base 16 clicks, top 14-18 clicks Base 12 clicks, top 1 1-14 clicks Base 10 clicks, top 10-12 clicks B ...

  • Ohlins SUPERBIKE FG 570 - page 21

    Notes 21 ...

  • Ohlins SUPERBIKE FG 570 - page 22

    T echnical information Fork length: 730 mm. Stroke: 130 mm. Free spring length: 260 mm. Rebound adjustment: Base setting 9-12 “clicks”. Maximum open valve 20 “clicks”. Compression adjustment: Base setting 6-16 “clicks”. Maximum open valve 20 “clicks”. Compression adjustment (Base valve): Base setting 6-16 “clicks”. Maximum open ...

  • Ohlins SUPERBIKE FG 570 - page 23

    1 - 2 T op nut assembly See page 24 2 01408-04 2 Adjustment driver 3 04744-95 04744-10 04744-90 2 2 2 Spring Option spring Option spring 25.5/260/9.5 25.5/260/10.0 25.5/260/9.0 4 01438-04 4 Guide ring 5 01460-37 2 Preload tube 6 01900-05 2 Fork leg outer 7 01683-02 2 Bushing, upper 8 01684-02 2 Bushing, lower 9 04758-01 2 W asher 10 04720-02 2 Seal ...

  • Ohlins SUPERBIKE FG 570 - page 24

    1 04747-02 2 Cap 2 04756-01 2 Adjuster 3 00884-04 4 Ball 4 04727-01 2 Spring 5 04722-07 2 O-ring 6 04748-01 2 Bolt spring adjuster 7 04722-04 4 O-ring 8 04749-02 2 Plate, center 9 02801-01 2 Adjustment housing 10 00338-61 2 O-ring 11 04751-02 2 W asher 12 04752-01 2 W asher 13 04753-01 2 W asher 14 04762-03 2 Spring seat Pos. Part No. Pcs. Descript ...

  • Ohlins SUPERBIKE FG 570 - page 25

    1 01654-07 1 Piston holder 2 00530-22 1 Shims 3 01149-01 1 W ave washer 4 00520-20 1 Shims 5 - 1 W asher See spec. card 6 - - Shim stack (comp.) See spec. card 7 01447-02 1 Piston ring 8 02061-03 1 Piston 9 - - Shim stack (reb.) 10 - 1 W asher See spec. card 11 01674-01 1 W asher 12 00153-01 1 W asher See spec. card 13 01675-01 1 Nut Pos. Part No. ...

  • Ohlins SUPERBIKE FG 570 - page 26

    26 1 00727-02 1 Soft jaws (one pair) 2 00786-05 1 Inner tube tool 3 00786-07 1 Cartridge tube tool 4 01781-01 1 Gas tool 5 00797-01 1 T op nut socket 6 01757-01 1 Attachment bar 7 01759-07 1 Dismantling bar 8 01759-08 1 Installing sleeve 9 01758-04 1 Guide ring 10 00720-02 1 Measure pin 11 00720-03 1 Pin tool 12 04705-01 1 Spanner 13 01765-03 1 Pul ...

  • Ohlins SUPERBIKE FG 570 - page 27

    Notes 27 ...

  • Ohlins SUPERBIKE FG 570 - page 28

    Mor e info www .ohlins.com Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby , Sweden Phone +46 8 590 025 00, Fax +46 8 590 025 80 07280-11, Issued 06 07 26. Öhlins Racing AB, Mattias Johansson/Update: Tiina Harakka ...

Fabricante Ohlins Categoría Motorcycle Accessories

Los documentos del dispositivo Ohlins SUPERBIKE FG 570 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Ohlins
- manuales de instrucciones SUPERBIKE FG 570
- hojas de producto Ohlins
- folletos informativos
- o etiquetas energéticas Ohlins SUPERBIKE FG 570
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Ohlins SUPERBIKE FG 570.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Ohlins SUPERBIKE FG 570, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Ohlins SUPERBIKE FG 570. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Ohlins SUPERBIKE FG 570.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Ohlins SUPERBIKE FG 570, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Ohlins SUPERBIKE FG 570. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Ohlins SUPERBIKE FG 570.

El manual de instrucciones completo de Ohlins debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Ohlins SUPERBIKE FG 570 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Ohlins SUPERBIKE FG 570, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Ohlins SUPERBIKE FG 570 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Ohlins SUPERBIKE FG 570 - que deben facilitarnos los primeros pasos durante el uso de Ohlins SUPERBIKE FG 570
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Ohlins SUPERBIKE FG 570
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Ohlins SUPERBIKE FG 570 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Ohlins SUPERBIKE FG 570?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Ohlins SUPERBIKE FG 570, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Ohlins SUPERBIKE FG 570 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)