-
Anetsberger Brothers SLG40 - page 1
1 FR FR FR FR FR YER YER YER YER YER Model SLG40 Anetsber ger Br others, Inc. 180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943 For ANETS Factory W arranty Service • 800-837-2638 Installation, User Operation, & Maintenance Manual Keep this Manual in a Convenient Location for Reference FOR YOUR SAFETY D ...
-
Anetsberger Brothers SLG40 - page 2
2 CONTENTS Shipping Container Inspection ....................................................... 3 Fryer Gas Supply Specifications .................................................... 3 Fryer Electrical Specifications ....................................................... 4 Figure 1 - Fryer W iring Diagram ......................................... ...
-
Anetsberger Brothers SLG40 - page 3
3 FR YER GAS SUPPL Y SPECIFICA TIONS Please mak e sur e that your desired fr y er location has gas supply factors that are suitable for this product: Gas Supply Inlet Pipe must be ½ “ standard gas line. The gas supply inlet line should be as straight as possible (fewest bends or elbows) to obtain the highest available gas pressure at the fryer . ...
-
Anetsberger Brothers SLG40 - page 4
4 IMPOR T ANT : Read the Code Requir ements and ALL installation instructions car efully , befor e starting the installation. Contact the fac- tory (800/ 837-2638) if any pr oblems or ques- tions arise. The fryer installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest editio ...
-
Anetsberger Brothers SLG40 - page 5
5 ! Figure 2. F r yer Model SLG40 Site Installation R equir ements CODE REQUIREMENTS CODE REQUIREMENTS CODE REQUIREMENTS CODE REQUIREMENTS CODE REQUIREMENTS (Continued) e. Install this fryer on a non-combustible floor with its back and sides at least 6 ” away from any combustible wall, as shown in Figure 2. WARNING Install this fryer under a vent ...
-
Anetsberger Brothers SLG40 - page 6
6 WARNING Fryers MUST have a movement- limiting (r estraining cable) device installed to pr event tipping that causes splashing or spilling its HOT contents. NOTE: This movement-limiting de- vice is to be furnished and in- stalled by the fr yer ’ s installing contractor before the fryer is con- nected to the gas line at its desired location. 1 . ...
-
Anetsberger Brothers SLG40 - page 7
7 INST INST INST INST INST ALLA ALLA ALLA ALLA ALLA TION REQ TION REQ TION REQ TION REQ TION REQ UIREMENTS UIREMENTS UIREMENTS UIREMENTS UIREMENTS (Continued) Figure 3. Typical Leg Installation LEG LEVELING INSTRUCTIONS 1. Move the fryer to its desired location. WARNING The fryer MUST NOT tip, rock or wob- ble, to avoid splashing or spilling its HO ...
-
Anetsberger Brothers SLG40 - page 8
8 CASTER LEVELING INSTRUC- TIONS 1. Move the fryer to its desired location. 2. Determine whether the fryer tends to wobble or rock when in its desired location. If it does , perform steps 3 through 9. If it does not, skip to step 10, then proceed to the Installation Instructions. WARNING The fryer MUST NOT tip, rock or wob- ble, to avoid splashing ...
-
Anetsberger Brothers SLG40 - page 9
9 GAS CONNECTION INSTRUCTIONS GAS CONNECTION INSTRUCTIONS GAS CONNECTION INSTRUCTIONS GAS CONNECTION INSTRUCTIONS GAS CONNECTION INSTRUCTIONS Installing your ANETS Fryer requires the fol- lowing procedure, after its legs or casters are pro- perly attached and it is in its desired location. 1. Ensure that the gas safety valve control knob in the fry ...
-
Anetsberger Brothers SLG40 - page 10
10 Please observe the following recommendations to obtain the optimum results from your ANETS Fryer . D ANGER A void moving the fryer while it contains HOT shortening. Drain the shortening from the fryer before moving it for service, clean- ing or maintenance to avoid spilling or splashing. Burns from hot shortening can cause serious injury or deat ...
-
Anetsberger Brothers SLG40 - page 11
11 Before using the newly installed fryer for food pre- paration, clean the rust preventive material from the kettle: 1 . Thoroughly wipe the interior of the kettle with clean cloths. Open the front door on the lower portion of the fryer to access the drain ball valve. Open the drain ball valve (by aligning the valve handle with the drain ball valv ...
-
Anetsberger Brothers SLG40 - page 12
12 SHUTDOWN PROCEDURE NOTE: Shutdown is recommended at the end of a workday or whenever no frying is scheduled for a period of several hours. T o prevent damage, the fryer MUST also be shutdown whenever there is no shortening in the kettle. 1. T urn the thermostat knob to OFF . 2. T urn the gas control valve knob to align the PILOT setting with the ...
-
Anetsberger Brothers SLG40 - page 13
13 FR FR FR FR FR YER OPERA YER OPERA YER OPERA YER OPERA YER OPERA TING INSTR TING INSTR TING INSTR TING INSTR TING INSTR UCTIONS UCTIONS UCTIONS UCTIONS UCTIONS (Continued) Load the fryer basket with the food pr oduct while the basket is not in the hot liquid shortening. DO NOT overload the fryer basket. Load only a pr emeasured quantity of food ...
-
Anetsberger Brothers SLG40 - page 14
14 DAIL Y CLEANING PROCEDURE NOTE: Cleaning is recommended at the end of a workday to prepare the fryer for proper operation the next time it is to be used. D ANGER A void moving the fryer while it contains HOT shortening. Drain the shortening from the fryer before moving it for service, clean- ing or maintenance to avoid spilling or splashing. [Re ...
-
Anetsberger Brothers SLG40 - page 15
15 NOTE: Regular maintenance is recommended to keep the fryer operating properly . Once each month, before beginning fryer opera- tion, check the flue (behind the backsplash panel) to ensure that it is clear and free of obstructions, enabling exhaust combustion gases to flow freely toward the ventilation hood area. DO NOT allow the flue to become e ...
-
Anetsberger Brothers SLG40 - page 16
16 FR FR FR FR FR YER YER YER YER YER TR TR TR TR TR OUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOO TING GUIDE TING GUIDE TING GUIDE TING GUIDE TING GUIDE Pilot flame does not stay lighted. 1. Dirty/sooty pilot burner . 2. Low gas supply pressure [less than 6 ” W .C. for natural gas (1 1 ” W .C. for pro- pane) when all other gas-powered equi ...
-
Anetsberger Brothers SLG40 - page 17
17 FR FR FR FR FR YER YER YER YER YER TR TR TR TR TR OUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOO TING GUIDE TING GUIDE TING GUIDE TING GUIDE TING GUIDE (Continued) Pilot flame goes out repeatedly . 1. Low gas supply pressure [less than 6 ” W .C. for natural gas (1 1 ” W .C. for pro- pane) when all other gas-powered equip- ment is operatin ...
-
Anetsberger Brothers SLG40 - page 18
18 Liquid shortening does not reach the desired temperature for frying. 1. Low gas supply pressure [less than 6 ” W .C. for natural gas (1 1 ” W .C. for propane) when all other gas-powered equipment is operating], causing reduced heat from main burners. 2. Low gas manifold pressure [less than 3½ ” W . C . for natural gas (10 ” W .C. for pr ...
-
Anetsberger Brothers SLG40 - page 19
19 NOTE: A Parts List for each ANETS Fryer is among the items shipped with each fryer . If an additional copy of this list is needed, please contact the factory as directed on the back cover . FR FR FR FR FR YER YER YER YER YER TR TR TR TR TR OUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOO TING GUIDE TING GUIDE TING GUIDE TING GUIDE TING GUIDE (C ...
-
Anetsberger Brothers SLG40 - page 20
20 Keep this Manual in a Convenient Location for Reference Anetsber ger Br others, Inc. 180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943 T oll-free Customer & W arranty Service: 800/ 837-2638 www .anetsberger .com Form: I-302 Rev . 9/03 Price: $20.00 US LIMITED W ARRANTY ANETSBERGER BROTHERS, INC., Nort ...
¿Tienes una pregunta acerca de Anetsberger Brothers SLG40?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Anetsberger Brothers SLG40, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Anetsberger Brothers SLG40 probablemente compartirá una forma de solucionarlo.