-
CDA ECHK90 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu ECHK90 & ECPK90 Extractors Manual for Installation, Use and Maintenance ...
-
CDA ECHK90 - page 2
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is no ...
-
CDA ECHK90 - page 3
3 safety (L VD) and Electromagnetic interference compatibility (EMC). IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposin ...
-
CDA ECHK90 - page 4
4 • This extractor has been designed to be used in a room with a volume of less than 36m. • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of ...
-
CDA ECHK90 - page 5
5 Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking. Control Panel A - Power o button B - Speed level buttons C - Light button T o switch the extractor light on or o • Press button “C” . T o switch on ...
-
CDA ECHK90 - page 6
6 Care and Maintenance IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . Cleaning Y ou should use a non-abrasive cleaner . Any abrasive cleaner (including Cif ) will scratch the surface and could erase the control panel markings. Y ou can clean you extractor eectively b ...
-
CDA ECHK90 - page 7
7 position to prevent damage from other items in the dishwasher . After rinsing and drying, replace the filters. T o remove the grease filters, pull open the handle on the grease filter . It will release at the handle side. Then lower the grease filter to remove it completely . T o replace the grease filter , repeat the steps in reverse. Pleas ...
-
CDA ECHK90 - page 8
8 Changing the Light IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . DO NO T CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HO T . ALL OW IT T O COOL BEFORE REMOVING IT . Carefully prise open the lamp assembly cover (D) using a small, flat-bladed scre ...
-
CDA ECHK90 - page 9
9 Bulb replacement is not covered by the guarantee. Only use bulbs recommended for your extractor . Do not fit bulbs of a higher power rating. Bulbs of a lower power rating may be adequate for use, generally last longer and use less energy . Mounting your Extractor When the extractor is to be installed above an electric hob, the minimum distance b ...
-
CDA ECHK90 - page 10
10 your hob being disconnected from the gas supply and the installation being reported to RIDDOR (The height should be measured from the top of the burners). IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS HOB, THE MINIMUM DIS T ANCE BETWEEN THE HOB AND EXTRA CT OR MUST BE A T LEAS T 760mm. The width of any hob must not be greater than the ...
-
CDA ECHK90 - page 11
11 Installation Note • W e recommend that you seek the help of another individual when installing this product. • The fixings supplied are suitable for most installations. It is the responsibility of the installer to ensure that the fixings are suitable for the ceiling type in the property . Installation 1. Firstly , fix the vent outlet to t ...
-
CDA ECHK90 - page 12
12 Fig. 9 calculation shown below for your extractor (refer to fig 4): A = Height of gas hob burner or electric hotplate height from the kitchen floor B = Clearance required: Gas hobs 750mm recommended Electric hobs: 650mm recommended A+B is the required height of the body of the extractor above the floor . Next we need to calculate the required ...
-
CDA ECHK90 - page 13
13 be at least the minimum height specified) 5. Place the chimney section over the body assembly , as shown in fig 8. 6. With the help of another individual, raise the whole assembly to the ceiling and fix securely in place using four screws appropriate for the wall plugs inserted in step 2. Ensure that the supporting ceiling is strong enough to ...
-
CDA ECHK90 - page 14
14 Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED T O THE MAINS SUPPL Y B Y A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWIT CHED FUSED SPUR OUTLET AND PROTECTED B Y A 3A FUSE. W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E ...
-
CDA ECHK90 - page 15
15 NO TE: USE A 3A FUSE Assembly and electrical connection should be carried out by competent personnel. When installing this product we recommend you seek the help of another individual. Do not mount the isolation switch behind the chimney section. It is a requirement that you must be able to isolate the extractor from the mains electrical supply ...
-
CDA ECHK90 - page 16
16 T roubleshooting If your extractor is not working: 1. Check that the mains supply has not been switched o . 2. Check that the fuse in the spur has not blown. Contact CD A Customer Care A: Customer Care Department, The CD A Group Ltd, Harby R oad, Langar , Nottinghamshire, NG13 9HY T : 01949 862 012 F: 01949 862 003 E: service@cda.eu W: www .c ...
-
CDA ECHK90 - page 17
17 ...
-
CDA ECHK90 - page 18
18 ...
-
CDA ECHK90 - page 19
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification echk90 ecpk90 Annual Energy Consumption AEC Hood 84.7 116.2 kWh Time increase factor f 1.6 1.7 Fluid Dynamic Efficiency FDE Hood 10.0 8.4 En ...
-
CDA ECHK90 - page 20
Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu ...
¿Tienes una pregunta acerca de CDA ECHK90?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA ECHK90, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA ECHK90 probablemente compartirá una forma de solucionarlo.