-
Zanussi ZGF982C - page 1
GAS HOBS ZGF982C INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB ...
-
Zanussi ZGF982C - page 2
2 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V ol t ageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Import ant Safety Information You MUST read hese warnings carefully before installing or using the h ...
-
Zanussi ZGF982C - page 3
3 For the User Content s For the Installer 1. Auxiliary Burner 2. Semi-rapid Burners 3. Ultra-rapid Double-crown Burner 4. Rapid Burner 5. Control knobs 2 1 3 4 5 2 Description of the Hob Important Safety Infor mati on 2 Description of the Hob 3 Operation 4 Maintenance and Cleaning 4 Something Not Working? 5 Guarantee Conditions 6 Instructions for ...
-
Zanussi ZGF982C - page 4
4 Maintenance and Cleaning Operation Hob burners T o light a burner: l push in the relevant control knob and turn it anticlockwise to maximum position; l then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. T o ensure maximum burner efficiency , you should only use pots and pans with a flat ...
-
Zanussi ZGF982C - page 5
5 Cast Iron Pan Support s The hob has cast iron pan supports. T ake care when removing them. They are fair heavy and could damage the hob or your kitchen furniture if you let them fall down. T o keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lif t them up as shown i ...
-
Zanussi ZGF982C - page 6
6 In the event of your appliance requiring service, or if you wish to purchase spare part s, please contact your local Zanussi Service Force Centre by telephoning: 0870 5 929929 Y our telephone call will be automatically routed to the Service Force Centre covering your post code area. The addresses are listed on the following pages. Before calling ...
-
Zanussi ZGF982C - page 7
7 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale, Guernsey Channel Islands JERSEY Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABERDEEN 54 Claremont Street (M05) Aberdeen A B10 6 RA ...
-
Zanussi ZGF982C - page 8
8 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM 66 Birch Road East (M18) Wyrley Road Ind. Estate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate (M44) Pinfold Road Bourne PE10 9HT BRIDGNORT H 68 St. Marys Street (M72) Bridgnorth Shropshire WV16 4DR GLOUCESTER 101 ...
-
Zanussi ZGF982C - page 9
9 BURNER RAPID SEMI-RAPID AUXILIARY (large) (m edium) ( small) POSITION M A X M IN M A X M IN M A X M IN M A X MI N NOMINAL THERMAL POWER kW 3 . 0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 NOMINAL FLOW RATE m 3 /h 0.286 0.062 0.190 0.043 0.095 0.031 0.333 0.114 NOZZLE REFERENCE 1 1 9 A d j u s t . 9 6 A d j u s t . 7 0 A d j u s t . 1 3 6 A d j u s t . NOMINA ...
-
Zanussi ZGF982C - page 10
10 FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 400 mm 100 mm 55 mm 50 mm 50 mm 600 mm 700 mm 400 mm 400 mm 100 mm 55 mm 600 mm 50 mm 50 mm FO 2369* FO 2231* Import ant safety requirement s This hob must be installed in accordance with the Gas Safety (Install ation and Use) Regulations ( ...
-
Zanussi ZGF982C - page 11
11 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 FO 2348 Dimensions are given in mm. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work su ...
-
Zanussi ZGF982C - page 12
12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240 ...
-
Zanussi ZGF982C - page 13
13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 (Ohm), check all earth wires for continuity and all conta ...
-
Zanussi ZGF982C - page 14
14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro ...
-
Zanussi ZGF982C - page 15
15 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguishe ...
-
Zanussi ZGF982C - page 16
35672-5603 12/00 Grafiche MDM - Forlì CUST OMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux Household Appliances Limited 2000 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More t ...
¿Tienes una pregunta acerca de Zanussi ZGF982C?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Zanussi ZGF982C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Zanussi ZGF982C probablemente compartirá una forma de solucionarlo.