-
SIIG 04-0600B - page 1
1 Satellite Speaker Mounts - 1 Pair Quick Installation Guide 04-0600B Introduction The Satellite Speaker Mounts - 1 Pair are fully-adjustable (Tilt, Swivel, & Pivot) speaker wall or ceiling mounts. Key Features and Benefits • Universal design fits most speaker brands & designs • Ceiling or wall mountable & compatible with 1, 2, or 4 ...
-
SIIG 04-0600B - page 2
2 Package Contents • (2) Speaker mounts • (2) 1-hole adapters • (2) 2/4-hole adapters • (2) 2 ¼” ceiling mount extensions • Mounting hardware • Quick installation guide Mounting Hardware M6x20mm Machine Screw M5 x 20mm Machine Screw 8-32 x 5/8" Machine Screw 1/4"-20 x 1/2" Machine Screw M5 x 1/8" Plastic Screw 8-3 ...
-
SIIG 04-0600B - page 3
3 Installation Please read the instructions prior to installation. This speaker mount is designed solely for the mounting of small speakers weighing less than 8lbs. We are not responsible for damage that may occur if speakers weighing more than 8lbs. are used. The user will have to determine which type of configuration will work best with the inclu ...
-
SIIG 04-0600B - page 4
4 2. Once the proper configuration is determined, secure the post to the speaker. 3. Some speakers use the smaller M4 x 8 screw, which is inserted into the off-center on the mounting post, see Figure 2 below. 4. Check the size of the hole, make sure you have the 8-32 x 5/8" machine screw, the 1/4"-20 x 1/2" machine screw, the M6 x 20 ...
-
SIIG 04-0600B - page 5
5 5. When the correct size is determined, place the screw through the speaker post and attach to the rear of the speaker enclosure. If the screw does not tighten properly, use the M5 x 1/8" plastic washer to tighten it up. Key Hole Mounting 1. If your speaker has a factory key hole design, you will use the 8-32 x 5/8" machine screws in co ...
-
SIIG 04-0600B - page 6
6 3. Engage the hex key hole nut into the key hole slot. 4. Put tension on the assembly by gently pulling back on the speaker mount post while tightening the 8-32 x 5/8" machine screw, see Figure 4 on page 5. 5. The hex key hole nut will engage on the housing in the key hole slot. 6. If the post does not tighten securely against the housing, i ...
-
SIIG 04-0600B - page 7
7 1/4"-20 x 1/2" Machine Screw 4-Hole Orientation 2-Hole Orientation Figure 5 Back Speaker Self-Tapped Mounting 1. Locate the optimum location for the mounting plate and use it as template to mark the drilling locations. Do not drill or screw into the speaker where you could possibly damage the internal components. 2. Drill the pilot hole ...
-
SIIG 04-0600B - page 8
8 Back Speaker #12 x 3/4" Self Tapping Screw Figure 6 Mounting to the Wall or Ceiling The mounting hardware for the three different surface applications is supplied. You will need to determine what style hardware will work best with your mounting surface. Always use caution when drilling into a wall or ceiling. Make sure to avoid all electrica ...
-
SIIG 04-0600B - page 9
9 #12 x 1 3/4" Self Tapping Screw Figure 7 3. Drill holes through the drywall and into the wood stud using a 1/8" drill bit. These holes should be drilled 1 1/2" deep, see Figure 7 above. 4. After the holes are drilled, mount the wall plate using the self tapping screws. Drywall Surfaces 1. Locate the best mounting location in the ce ...
-
SIIG 04-0600B - page 10
10 4. With the anchors in place, mount the wall plates using the #12 x 3/4" self tapping screws, see Figure 8 below. Figure 8 #12 x 3/4" Self Tapping Screw Insert screw through wall plate and into the alligator anchor Insert Alligator Anchor Pre Drill 5/16" Holes Concrete Surface 1. Using the wall plate as a template, mark hole posit ...
-
SIIG 04-0600B - page 11
11 Figure 9 Insert Alligator Anchor #12 x 3/4" Self Tapping Screw Using the hammer to tap anchor into place Insert screw through wall plate and into the alligator anchor 3. With the wall anchor in place, mount the wall plate using the #12 x 3/4" self tapping screws, see Figure 9 above. Extension Mounting This is for ceiling and/or shelf a ...
-
SIIG 04-0600B - page 12
12 Low-Profile Mounting This is for wall and ceiling application. 1. Install the low-profile portion of the speaker mount to the wall plate or 2 1/4" extension. 2. Secure the setscrew to hold the extension in place with the weight of the speaker attached. Tighten the allen screw using the provided allen wrench. Figure 11 Speaker Mounting 1. In ...
-
SIIG 04-0600B - page 13
13 Blank Page ...
-
SIIG 04-0600B - page 14
14 Blank Page ...
-
SIIG 04-0600B - page 15
15 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst ...
-
SIIG 04-0600B - page 16
PRODUCT NAME Satellite Speaker Mounts - 1 Pair FCC RULES: TESTED TO COMPL Y WITH FCC P ART 15, CLASS B OPERA TING ENVIRONMENT : FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this de ...
¿Tienes una pregunta acerca de SIIG 04-0600B?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con SIIG 04-0600B, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con SIIG 04-0600B probablemente compartirá una forma de solucionarlo.