-
Sears 200.7123 - page 1
OWNER'S MANUAL DieHard, BATI'ERY CHARGER 40/2 Amp Manual 200 Amp ENGINE STARTER Model No. 200.71230 CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 0099000312-402 ...
-
Sears 200.7123 - page 2
Table Of Contents Warranty .................................................................... 1 Important Safety Instructions ................................. 2 Parts .......................................................................... 3 Before UslngYour Battery Charger ........................ 4 Assembling your charger ................... ...
-
Sears 200.7123 - page 3
Important Safety Instructions - SAVE THESE INSTRUCTIONS - • Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. • Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, tractors, airplanes, vans, RV's, trolling motors, etc. This charger ...
-
Sears 200.7123 - page 4
Parts This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. ; Item Description Pert Number 1. Handle 3599000286 2. Negative (BLK) Cable w/Clamps 3899000396 3. Positive (RED) Cable w/Clamps 3899000410 4. Power Cord 90026096 5. Circuit Breaker Assembly 3999 ...
-
Sears 200.7123 - page 5
Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use. Follow these instructions for easy assembly. PARTS: Two 10-3 ...
-
Sears 200.7123 - page 6
3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided. To attach the handle: Turn the charger right side up onto its foot ...
-
Sears 200.7123 - page 7
A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. ,_ WARNING: Improper adapter con- nection can result in electrical shock. Before using an adapter as illustrated, be certain th ...
-
Sears 200.7123 - page 8
Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle. Setting the controls All the controls for your charger are located on the front of the unit. Follow these instructions to obtain the ...
-
Sears 200.7123 - page 9
Charging Your Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engine pads. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury. 3. Check the polarity of the battery posts using the identi ...
-
Sears 200.7123 - page 10
Charging your battery outside the vehicle: 1. Remove the battery from vehicle, making sure to disconnect grounded terminal first with all power turned off to the vehicle. 2. Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -). NOTE: On top-post batteries, the positive battery termi ...
-
Sears 200.7123 - page 11
Calculating charge times The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chad. • Small batteries -- motorcycles, garden tractors, etc. -- are usually rated in Ampere Hours (AH). For example: 6 to 12 AH, or 12 to 32 AH. ? ...
-
Sears 200.7123 - page 12
Using the engine start feature Your battery charger can be used to jump-start your car if the battery is low. Follow these instructions on how to use the engine start feature. 1. Set the right-hand OUTPUT SELECTOR switch to the OFF position. Then follow the instructions for connecting the charger to the battery in the section "Charging your ba ...
-
Sears 200.7123 - page 13
Troubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM No reading on the ammeter. No reading on ammeter. Fan inside wheel charger appears to not be working. Circuit breaker in charger cycles on and off with a clicking sound. ...
-
Sears 200.7123 - page 14
For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CT Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). For repair parts or the location of a Sears Parts and Repair Center call: 1-800-4-MY-HOME = (t400-469-4663), ...
¿Tienes una pregunta acerca de Sears 200.7123?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 200.7123, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 200.7123 probablemente compartirá una forma de solucionarlo.