-
Sanyo VCB-3374 - page 1
INSTRUCTION MANUAL B/W CCD Camera VCB-3374 About this manual • Before inst alling and usin g th e came ra, pl ease read t his manu al car efull y. Be sure to keep it handy for later reference. L73K 4/U S GB 19 98 , 3, 11 ...
-
Sanyo VCB-3374 - page 2
SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained b ...
-
Sanyo VCB-3374 - page 3
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER .................................. 2 PRECAUTIONS ................................................... 3 PARTS N ...
-
Sanyo VCB-3374 - page 4
Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform to all local codes. ...
-
Sanyo VCB-3374 - page 5
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For ...
-
Sanyo VCB-3374 - page 6
PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment screw (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this screw. 3 24 V ...
-
Sanyo VCB-3374 - page 7
PARTS NAMES 8 Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 9 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. Howeve ...
-
Sanyo VCB-3374 - page 8
F Flange-back adjustment screw (FLANGE BACK ADJ.) G Flange-back lock screw (FLANGE BACK LOCK) Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flang ...
-
Sanyo VCB-3374 - page 9
MOUNTING THE LENS Installation of a VIDEO type auto-iris lens (sold separately) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. 1 Remove the lens mount cap. 2 Attach the supplied C mount adaptor (A) to the auto-iris lens (B) , then install the assembly on the camera. 3 Connect the lens ...
-
Sanyo VCB-3374 - page 10
Compatible auto-iris lenses 1/3 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 12 mm VCL-CS2LY: Ultra-wide angle, f= 2.8 mm More telephoto angle, f= 16 mm If using a VIDEO type auto-iris lens • Set the ALC and LEVEL controls on t ...
-
Sanyo VCB-3374 - page 11
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Insert the plug of this power cord into a wall outlet. The POWER indicator (A) will light. Adjust the picture on the mon ...
-
Sanyo VCB-3374 - page 12
SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/BLC switch to EI-ON position. Note: Please refer to the specifications for dynamic range of the electronic iris. CAUTION: • The electronic iris is suitable for normal indoor use. When the EI/BLC switch is set to t ...
-
Sanyo VCB-3374 - page 13
SETTINGS Backlight compensation setting Use an auto-iris lens and set the EI/BLC switch to the BLC-ON position, to engage the backlight compensation function. Use an auto-iris lens. Set the EI/BLC switch to BLC-ON switch to the ON position. If using a VIDEO type auto-iris lens • The ALC volume on the lens should be turned all the way to Av (Avera ...
-
Sanyo VCB-3374 - page 14
TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen • Is the power turned on to all connected devices? Is the voltage correct? • Are all th ...
-
Sanyo VCB-3374 - page 15
SPECIFICATIONS Scanning system : EIA standard (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 811 (H) x 508 (V) Effective picture elements : 768 (H) x 494 (V) Synchronizing system : Line lock/External sync (Automatic switching) Resolution : 570 TV lines horizontall ...
¿Tienes una pregunta acerca de Sanyo VCB-3374?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sanyo VCB-3374, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sanyo VCB-3374 probablemente compartirá una forma de solucionarlo.