-
Cambridge Audio Audio Cable KP10 - page 1
KP10 A -BUS k e ypad Installation Guide ...
-
Cambridge Audio Audio Cable KP10 - page 2
2 Incognito KP1 0 CONTENTS Introduction.......................................................3 System options.................................................4 Installation not es..............................................8 Rear panel connections................................. 1 0 K eypad contr ols............................................. ...
-
Cambridge Audio Audio Cable KP10 - page 3
Incognito A-BUS ke ypad 3 Thank you for purchasing this Cambridge Audio Incognito product. Incognito is a cost-effective, modular based system using standard Cat-5 or Cat-6 cable to distribute hi-fi quality sound and video around a home. The KP1 0 is an in-wall, A-BUS TM compatible amplified k eypad with butt ons f or control of speak er volume le ...
-
Cambridge Audio Audio Cable KP10 - page 4
The KP1 0 k eypad can be used in two main configurations: 1. As par t of a full Incognito syst em, where it is plugged into an Incognito hub (AH1 0), perhaps with other Incognit o accessories such as a video switching unit (VH1 0) or local input module (LM1 0) fitted. 2. Where the k eypad is plugged directly int o an A -BUS Ready/Incognit o Ready o ...
-
Cambridge Audio Audio Cable KP10 - page 5
Incognito A-BUS ke ypad 5 Speaker cable PS10 Speaker cable SS10 SS10 AH10 Cat-5/5e cable KP10-EU KP10-EU KP 1 0 A -BUS k eypad ...
-
Cambridge Audio Audio Cable KP10 - page 6
A-BUS Ready / Incognito Ready For use with an A-BUS Ready/Incognit o R eady unit (see diagram opposite) the Mode switch MUS T be in the "Standard A-BUS/Incognito Ready" position as sho wn below: In this configuration the ke ypad is wired directly to the am plifier/receiver . A Po wer Supply Unit (PS1 0) is also required t o pow er the one ...
-
Cambridge Audio Audio Cable KP10 - page 7
Incognito A-BUS ke ypad 7 Impedance 4 - 8 ohms Loudspeaker Terminals Important Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées Impedance 4 - 8 ohms Right Left Right Left Left B A Left Right Right B A IR1 IR2 IR4 IR3 Keypad 1 Keypad 2 Pre-Out Tape In Re ...
-
Cambridge Audio Audio Cable KP10 - page 8
8 Incognito KP1 0 The KP1 0 is fitted on the w all by fixing it into a standar d UK 4 7mm depth single-gang electrician’s back-bo x (pattress). All knock-outs in the back -box should be remo ved t o pro vide maximum ventilation. Where it is desired to fit a mains lighting switch etc ne xt to a k eypad, a barrier -box or two single back-bo xes mus ...
-
Cambridge Audio Audio Cable KP10 - page 9
Incognito A-BUS ke ypad 9 Safety precautions Care should be tak en when choosing the site f or a KP1 0, the k eypad must ne ver be installed in a back-bo x which also contains mains wiring or in areas of high humidity . The KP1 0 runs on 2 4 V DC supplied through the connecting cable. As such there is no mains voltage present in the KP1 0 and the u ...
-
Cambridge Audio Audio Cable KP10 - page 10
Cat5 to KP10 punch down connectors A Cat-5 cable (terminat ed with an RJ45 jack plug) is used to connect the KP1 0 to an AH1 0 hub or A-BUS Ready receiv er . The KP1 0 has punch down connect ors for the eight individual conductors of the Cat-5 cable (use a small flat-bladed screwdriv er). See below f or the EIA/TIA 568A wiring standard: 10 Incognit ...
-
Cambridge Audio Audio Cable KP10 - page 11
Incognito A-BUS ke ypad 11 Line-in/Line-out connections on subwoofer Screened audio cable Preamp output connections on rear of KP10 Gain adjust The maximum output of the KP1 0 can be limited b y turning these down. Alt ernatively , if the sound lev el is too q uiet, the Gain can be turned up. Mode switch Selects between AH1 0 mode and Standard A-BU ...
-
Cambridge Audio Audio Cable KP10 - page 12
12 Incognito KP1 0 The six LEDs indicate the function status of the KP1 0. List ed below are each of the functions of the corresponding LEDs: Minimum volume / Source select Volume / Source select / Bass adjust / Local Source Selection Mode Volume / Source select / Treble adjust / Local Source Selection Mode Volume / Source select / Balance adjust / ...
-
Cambridge Audio Audio Cable KP10 - page 13
Incognito A-BUS ke ypad 13 Standby/On Press to switch the k eypad between On and Standb y mode. By pressing and holding the Standby butt on f or about 2 seconds, all KP1 0s connected t o the AH1 0 hub will be turned of f. If the KP1 0 is connected t o a Cambridge A udio Incognito R eady Amplifier rather than an AH1 0 hub, the amplifier will be turn ...
-
Cambridge Audio Audio Cable KP10 - page 14
14 Incognit o KP10 OPERA TING INSTRUCTIONS Important! As mentioned previously , the KP1 0 can be switched between two modes of operation; a standard A-BUS mode f or compatibility with other manufacturers A-BUS Ready eq uipment (Standard A-BUS/Incognito R eady mode), and an Incognito A-BUS hub mode (AH1 0 mode). When used with other manufacturers A- ...
-
Cambridge Audio Audio Cable KP10 - page 15
Af ter holding bo th buttons down f or a shor t period, the second LED on the k eypad will light indicating that Bass adjust mode has been activat ed. In this mode pressing the V olume up/down k e ys will adjust the Bass (low frequencies) le vel. Continuing to hold bo th ke ys down will light the third LED indicating that Treble adjust mode has bee ...
-
Cambridge Audio Audio Cable KP10 - page 16
16 Incognito KP1 0 Note: This f eature is only av ailable if the KP1 0 is par t of a full Incognito multi-r oom system with one or two Local In put Modules (LM1 0) fitted. The local source selection mode will need t o be activat ed to configure the KP1 0 correctly . This mode is only a vailable when the Mode Switch is set to “ AH1 0” mode. LM10 ...
-
Cambridge Audio Audio Cable KP10 - page 17
Incognito A-BUS ke ypad 17 Continuing to hold V olume up and Po wer buttons will light LED 5, t o indicat e that Off mode is a vailable f or selection, and no source will be select ed. T o select these modes, wait till the corresponding LED is lit and then release Po wer and V olume up buttons. Note: If no adjustment is made the system will aut oma ...
-
Cambridge Audio Audio Cable KP10 - page 18
18 Incognit o KP10 Input impedance 45 k ohms Frequency response 20Hz – 20kHz +/- 1dB THD <0.2% @ 1W , 20Hz – 20 kHz S/N ratio > 80 dB ‘A ’ weighted Volume control range - 80 dB, 36 st eps Bass control range +/- 1 6 dB, 2 dB st eps Treble control range +/- 1 6 dB, 2 dB st eps Balance control range +/- 40 dB, 9 steps either w ay Preamp ...
-
Cambridge Audio Audio Cable KP10 - page 19
Incognito A-BUS ke ypad 19 Cambridge Audio w arrants this product t o be free from def ects in materials and workmanship (subject t o the terms set f or th below). Cambridge A udio will repair or replace (at Cambridge Audio’s option) this pr oduct or any def ective parts in this product. W arranty periods may vary from countr y to country. If in ...
-
Cambridge Audio Audio Cable KP10 - page 20
Incognito KP10- EU www.cambridge-audio.com Par t No. AP18303/2 ...
¿Tienes una pregunta acerca de Cambridge Audio Audio Cable KP10?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cambridge Audio Audio Cable KP10, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cambridge Audio Audio Cable KP10 probablemente compartirá una forma de solucionarlo.