-
Makita 6012HDW - page 1
Cordless Steel Wood Driver Dr i I I Wood screw Machine screw Nuts MODEL 6012HD MODEL 6012HDW With Fast Charger and Carrylng Case 6 5 mm 1114"l INSTRUCTION MANUAL 15 mm 5.1 mm x 55 mm 6 mm 261 mm 1.6 kg 1518") 13/16" x 2-118") 1114") I :Em) 1 400 ' lrloo 1 110-114") 1 13.5 lbsl S PECl F I CAT1 0 N S Battery Cartrid ...
-
Makita 6012HDW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in ...
-
Makita 6012HDW - page 3
13. DISCONNECT TOOLS. When not in use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on ...
-
Makita 6012HDW - page 4
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Length of Cord (Feet) 25 50 AWG Size of Cord 18 18 SAVE THESE INSTRUCTIONS - This manual 100 150 18 16 Do not operate charger with damaged cord or plug - replace them imme- diately. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified ser ...
-
Makita 6012HDW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5O0F1 or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the batte ...
-
Makita 6012HDW - page 6
Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge with ...
-
Makita 6012HDW - page 7
When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, ...
-
Makita 6012HDW - page 8
Drill *Punch a small hole in the metal to pre- vent the bit from skitterring when start- ing to drill a hole. 0 Use drill machine oil on the bit to facilitate ing. .Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve to damage the tip of your drill bit, decrease your drilling per- formance ...
-
Makita 6012HDW - page 9
Screw Match vour bit to vour screw. Item I Nominal diameter (mm) Bit No. I Wood screw I Machine screw I I 2.1 - 2.7 M2 - M2.6 3.1 - 4.8 M3 - M5.5 Phillips bits Phillips bit No. 2-65 mm is standard equipped. Select your screws and nominal diameter with the chart on the right. No. 3 I 5.1 (13/64") I M6 (1/4") Slotted bits Unless you use a b ...
-
Makita 6012HDW - page 10
Speed changeover .To change the speed, turn the speed change knob 180" while the drill is run- ning. Be sure that the speed change knob is turned to the correct speed setting before you begin operation. See arrow indication. Use the right speed for the job. Fastening torque adjustment Just turn the fastening torque adjust knob on the tool in o ...
-
Makita 6012HDW - page 11
*The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. I 11 ...
-
Makita 6012HDW - page 12
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Fast charger Model DC9700 0 Charger 12V for ...
-
Makita 6012HDW - page 13
0 Tool holster has some bits storage space. Use holster to carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-36 Part No. 823033-3E (Genuine leather) 0 Tool carrying case Part No. 823085-7 (Steel case) Part No. 824145-8 (Plastic case) 13 ...
-
Makita 6012HDW - page 14
Feb 19 86 EN CORDLESS DRIVER DRILL Model 6012HD Note: The switch and other part configurations may differ from country to country 14 ...
-
Makita 6012HDW - page 15
MODEL 6012HD Feb-19-86 EN ED DESCRIPTION I;,'," DESCRIPTION MACHINE ______ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Pan Head Screw M5x18 Drill Chuck S10 Spindle Pi" 3 Ball Bearinq 6000LLB STOP Ring E 9 Thin Washer 10 Spur Gear 78 Ring 16 Spur Gear 93 Thin Washer 10 ...
-
Makita 6012HDW - page 16
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has be ...
¿Tienes una pregunta acerca de Makita 6012HDW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6012HDW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6012HDW probablemente compartirá una forma de solucionarlo.