-
Graco 308371K - page 1
Instructions – Parts List GRACO INC.ąP .O. BOX 1441ąMINNEAPOLIS, MNą55440-1441 Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001 ST AINLESS STEEL, HEA VY–DUTY Agitators 100 psi (0.7 MPa, 7 bar) Maximum Working Pressure T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Instal ...
-
Graco 308371K - page 2
2 308371 Symbols W arning Symbol W ARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. W ARNING EQUIPMENT MISUSE HAZARD Equipment misuse can c ...
-
Graco 308371K - page 3
308371 3 W ARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and result in a fire or explosion and serious injury . D Ground the equipment and the object being sprayed. Refer to Grounding on page 4. D If there is any static sparking or you feel an electric shock while using ...
-
Graco 308371K - page 4
4 308371 Installation W ARNING FIRE AND EXPLOSION HAZARD Always maintain a minimum of 1 in. clearance between rotating agitator parts and container to prevent sparks from contact. air line lubricator agitator motor air line filter air regulator and gauge mix tank (reference only) T ypical Installation NOTE: Reference numbers and letters in parenthe ...
-
Graco 308371K - page 5
308371 5 Notes ...
-
Graco 308371K - page 6
6 308371 Installation If installing an agitator onto a non-agitated tank, follow steps 1, 2, and 7 through15. If installing a heavy-duty agitator in place of a standard agitator , follow pages 1, 3 through 12, 14, and 15. 1. Follow the Pressure Relief Procedure above. Then remove the pressure tank cover from the tank. 2 . See Fi g. 3 . Unscrew and ...
-
Graco 308371K - page 7
308371 7 Installation 12. Align the agitator paddle (12) on the agitator shaft (14) as instructed for your model, as follows: Models 236662 and 236663 (10 & 15 Gallon) Align the top of the paddle hub (G) with the mark (H) on the agitator shaft (14). Model 236661 (5 Gallon) If a 5 gallon pail is to be placed inside the pressure tank (5 gallon ta ...
-
Graco 308371K - page 8
8 308371 Operation W ARNING T o reduce the risk of serious bodily injury , which can result if the tank pressure is not fully relieved, always follow the Pressure Relief Procedure on page 6 before opening the tank cover or fill port. 1. Fill the pressure tank as explained in the Pressure T ank Instruction Manual 308369. 2. Screw on the filler cap ( ...
-
Graco 308371K - page 9
308371 9 Service W ARNING T o reduce the risk of serious bodily injury , including cuts, amputation of fingers, and splashing in the eyes or on the skin, always follow the Pressure Relief Procedure on page 6, shut off the agitator , and disconnect the air line before checking or repairing the agitator . Lubricating the Heavy-Duty Agitator CAUTION N ...
-
Graco 308371K - page 10
10 308371 Service D If the unit requires more than installation of a service kit, it is usually quickest and easiest to send the unit to the Graco distributor for repair or replacement. D If the vanes need replacing, or if foreign material is present in the motor chamber , an experienced mechanic may remove the end plate opposite the drive shaft en ...
-
Graco 308371K - page 11
308371 1 1 Service Servicing the Agitator Shaft and Couplings (See Fig. 7) Setting the Agitator Shaft Coupling 1. With the agitator shaft (14) pushed up against the washer (15a), secure the lower portion of the coupling half (19b) to the shaft by tightening the coupling setscrew against the flat on the shaft. Leave about a 0.015 in. gap between the ...
-
Graco 308371K - page 12
12 308371 Parts Drawing Apply low-strength (cyanoacrylate) thread sealant. Orient collar (4) with slots facing up and down. Orient screws (32) on collar (2) to either side of slots on mounting collar (4). Remove original bolts, and replace with (33). T orque to 160 in-lbs (18 N-m). Locate the bottom shoulder of shaft (14) against washer (15) when a ...
-
Graco 308371K - page 13
308371 13 Parts List Stainless Steel, Heavy-Duty Agitators Model No. 236661, 5-gallon size Model No. 236662, 10-gallon size Model No. 236663, 15-gallon size Ref Part No. No. Description Qty . Ref Part No. No. Description Qty . 1 162425 MOT OR, air 1 2 181849 COLLAR 1 3 100828 COUPLING, flexible 1 4 220416 COLLAR, mounting; Includes items 4a & 4 ...
-
Graco 308371K - page 14
14 308371 T echnical Data Heavy-Duty Models 236661, 236662, and 236663 For fluid viscosity above 800 cps (centipoise) Air motor: air driven, gear reduced, 1/2 HP (373 W) Air pressure: 100 psi (0.7 MPa, 7 bar) maximum Gear ratio: reduced 20:1 shaft rpm is 1/20 of air motor rpm Wetted parts: 304 and 316 stainless steel, PTFE, Zytel r , and bronze Wei ...
-
Graco 308371K - page 15
308371 15 Notes ...
-
Graco 308371K - page 16
16 308371 Graco Standard W arranty Graco w arrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco w ill, for a period of twelve months from th ...
¿Tienes una pregunta acerca de Graco 308371K?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Graco 308371K, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Graco 308371K probablemente compartirá una forma de solucionarlo.