-
Sears 200.71206 - page 1
SAFETY 1 PARTS MAINTENANCE TROUBLESHOOTING OPERATION 0000000508-1196 OWNER’S MANUAL 6/2 AMP MANUAL BATTERY CHARGER Model No. 200.71206 CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. ...
-
Sears 200.71206 - page 2
2 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY TABLE OF CONTENTS WARRAN WARRAN WARRAN WARRAN WARRAN T T T T T Y Y Y Y Y Warranty ...................................................................................................... 2 Important Safety Instructions .................................................................... 3 Before Us ...
-
Sears 200.71206 - page 3
SAFETY 3 PARTS MAINTENANCE TROUBLESHOOTING OPERATION IMPORTANT SAFETY INSTRUCTIONS • Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. • Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, tractors, air- planes, vans, RV’s, trolling mo ...
-
Sears 200.71206 - page 4
4 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY For your own personal safety, please follow the following precautions: Wear complete eye and clothing protection when working with lead- acid batteries. Be sure that someone is within range of your voice to come to your aid if needed while you work with or are near a lead-acid battery. ? ...
-
Sears 200.71206 - page 5
SAFETY 5 PARTS MAINTENANCE TROUBLESHOOTING OPERATION BE FO R E USING YOUR BA T TER Y C HAR GER It is important to prepare your charger for use. This section will tell you about your charger's electrical requirements and how to prepare a battery for charging. DANGER: Before using an adapter as illustrated, be certain that the center screw of th ...
-
Sears 200.71206 - page 6
6 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY PREPARING YOUR BATTERY TO BE CHARGED It is important that you read and follow these guidelines while you are preparing to charge your battery. • Make sure that you have a 12 volt lead-acid battery. • Clean the battery terminals. Be careful to keep corrosion from getting in or around your eyes ...
-
Sears 200.71206 - page 7
SAFETY 7 PARTS MAINTENANCE TROUBLESHOOTING OPERATION When using the ENGINE START feature, the needle will swing into the Start (red) area of the scale while you are cranking the engine. The percent of charge scale is intended as a visual aid to help simplify reading the state of charge of the battery. The meter is scaled for use with the 10 amp cha ...
-
Sears 200.71206 - page 8
8 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY Charging your battery outside the vehicle: POSITIVE NEGATIVE BATTERY CHARGER POWER CORD BATTERY + - TO GROUNDED POWER OUTLET Figure B (NEGATIVE) lead of the charger to the free end of the cable. Rock the clamp to make a solid connection. IMPORTANT: Wear safety glasses and face away from the batte ...
-
Sears 200.71206 - page 9
SAFETY 9 PARTS MAINTENANCE TROUBLESHOOTING OPERATION CALCULATING CHARGE TIME The Chart Method Use the following table to more accu- rately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries — motorcycles, garden tractors, etc. — are usually rated in Ampe ...
-
Sears 200.71206 - page 10
10 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY (A battery at 50 percent charge that will be charged to 100 percent needs another 50 percent (.50). • Multiply the Amp Hour rating by the charge needed (.50) and divide by the charger setting (2 or 6 amps). • Multiply the result by 1.25 and you’ll have the approximate time needed, in hours ...
-
Sears 200.71206 - page 11
SAFETY 11 PARTS MAINTENANCE TROUBLESHOOTING OPERATION MAINTENANCE AND CARE A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatl ...
-
Sears 200.71206 - page 12
12 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY TROUBLESHOOTING Performance problems often result from little things that you can fix yourself. Please read through this chart for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No ammeter reading. Clamps not making good connection. 2-amp charge rate. No AC powe ...
-
Sears 200.71206 - page 13
SAFETY 13 PARTS MAINTENANCE TROUBLESHOOTING OPERATION Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Replacement Parts List Sears 71206 Description Part Number Cover 3799001402 Heatsink/Diode Assembly 2299000825 Base 3799001382 AC Power Cord 90026058 Transformer 93026433 Output Cable 3899000016 Circuit Breaker (12A) 3999000044 50A Clamp (1) 2299000248 Sl ...
-
Sears 200.71206 - page 14
14 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY WIRING DIAGRAM ...
-
Sears 200.71206 - page 15
SAFETY 15 PARTS MAINTENANCE TROUBLESHOOTING OPERATION NOTES ...
-
Sears 200.71206 - page 16
16 TROUBLESHOOTING MAINTENANCE PARTS OPERATION SAFETY For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information about troubleshooting Call toll-free from anywhere in the ...
¿Tienes una pregunta acerca de Sears 200.71206?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 200.71206, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 200.71206 probablemente compartirá una forma de solucionarlo.