-
Makita 6211DH - page 1
Cordless Driver Drill Capacities Steel Wood Wood screw Machlne screw 10" 21" 6.4mmx55mm 6mm,1,4,,) (318'7 (13/16"1 1114" x 2-3/16") Equipped with Electric Brake MODEL 621 1 DH MODEL 621 1 DWH With Fast Charger Dimensions Net IL x W x HI No load speed IRPMl weight High tow o~1,150 o-370 233mmx79mmx233mm LBkg 19-3/16&quo ...
-
Makita 6211DH - page 2
I M PO RTA N T SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRON ...
-
Makita 6211DH - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cord ...
-
Makita 6211DH - page 4
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Length of Cord (Feet) ...
-
Makita 6211DH - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte ...
-
Makita 6211DH - page 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal or the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery cartridge with t ...
-
Makita 6211DH - page 7
Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clock ...
-
Makita 6211DH - page 8
Speed change To change the speed, slide the speed change lever to the "H" side for high speed or "L" side for low speed. To slide the speed change lever easily, pull the trigger slightly while pushing the speed change lever. Be sure that the speed change lever is set to the correct position before operation. Use the right speed ...
-
Makita 6211DH - page 9
When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. Nominal diameter af wood Screw lmml 3.1 (118") 3.5 19/64") 3.8 15/32") 4.5 111/64'l 4.8 13/16") 5.1 /13/64') 5.5 17/32") 5.8 17132"l 6.1 (15164") 6.4 (1/4"1 Drilling oper ...
-
Makita 6211DH - page 10
Hook A hook is provided as a standard equip- ment. This hook is convenient for tem- porarily hanging the tool. To install the hook, first insert one end of the hook into one slot in the .tool body and then insert the other end into the other slot. Secure the hook with the screw. The hook can be installed on either left or right side of the tool. Ho ...
-
Makita 6211DH - page 11
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11 ...
-
Makita 6211DH - page 12
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bit I Size I Part NO. Phillips 1 ;: 784214-0A 7 ...
-
Makita 6211DH - page 13
CORDLESS DRIVER DRILL Model 6211D Note: The switch and other part configurations may differ from country to country. 13 ...
-
Makita 6211DH - page 14
'LtM DESCRIPTION :tM ASD DESCRIPTION MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 10 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 7 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 - Name Rata Tapping Screw PT4xl8 Housing Set [With Item 591 Pan Head Screw M4x22 IWith Washer) Sponge 14-72 Switch Lever Switch Lever Koylws Drill Chuck 1 ...
-
Makita 6211DH - page 15
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. 1 Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center i I or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that ha ...
¿Tienes una pregunta acerca de Makita 6211DH?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6211DH, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6211DH probablemente compartirá una forma de solucionarlo.