-
Multiquip CDM1H - page 1
OPERA TION AND P AR TS MANUAL THIS MANU AL MUST A CCOMP ANY THE EQUIPMENT A T ALL TIMES. T o find the latest revision of this publication, visit our website at: www .m ultiquip.com MODEL CDM1H HAND-HELD CORE DRILL (ELECTRIC MOTOR) Re vision #6 (09/08/10) ...
-
Multiquip CDM1H - page 2
P A GE 2 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) Engine exhaust and some of its constituents, and some dust created of California to cause cancer , birth defects and other repr oductive harm. by power sanding, sawing, grinding, drilling and other construction activities contains chemicals kno wn to the State So ...
-
Multiquip CDM1H - page 3
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 3 Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay , granite and numerous other minerals and rock ...
-
Multiquip CDM1H - page 4
P A GE 4 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — T ABLE OF CONTENTS Specification and part number are subject to change without notice . Multiquip CDM1H Hand-Held Core Drill Proposition 65 W ar ning ............................................. 2 Silicosis W ar ning .............. ...
-
Multiquip CDM1H - page 5
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 5 CDM1H HAND-HELD CORE DRILL — P AR TS ORDERING PR OCEDURES www .multiquip .com Or dering par ts has never been easier! Choose fr om three easy options: WE A CCEPT ALL MAJOR CREDIT CARDS! When or dering par ts, please supply: R Dealer Account Number R Dealer Name and ...
-
Multiquip CDM1H - page 6
P A GE 6 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) Other impor tant messages are pro vided throughout this manual to help pre vent damage to y our dr ill, other proper ty , or the surrounding environment. CA UTION - Equipment Damage Hazards AL W A YS wear approv ed e ye and hearing protection. CA UTION - Eye and ...
-
Multiquip CDM1H - page 7
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 7 CDM1H HAND-HELD CORE DRILL — RULES FOR SAFE OPERA TION The following safety guidelines should always be used when operating the MQ Model CDM1H Core Drill. GENERAL SAFETY ■ DO NO T operate or ser vice this equipment before reading this entire manual. ■ This equip ...
-
Multiquip CDM1H - page 8
P A GE 8 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — R ULES FOR SAFE OPERA TION ■ Maintain the core drill and dr ill bits with care. K eep drill bits sharp. Sharp cutting edges are less likely to bind. ■ If drilling into a workpiece that is unattached, use clamps or other means to ...
-
Multiquip CDM1H - page 9
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 9 TRANSPORTING ■ AL W A YS place the core dr ill inside its carr ying case when work has been completed. ■ AL W A YS wrap pow er cord neatly to av oid damage. ■ AL W A YS place wrenches back into carrying case when work has been completed. MAINTENANCE ■ NEVER lu ...
-
Multiquip CDM1H - page 10
P A GE 10 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — GENERAL INFORMA TION APPLICA TION The MQ CDM1H Hand-Held Core Drill is designed to be used for either dry or wet drilling applications involving con- crete type materials. Up to 3-inch (76.2 mm) diameter holes can be drilled for we ...
-
Multiquip CDM1H - page 11
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 11 Figure 2. CDM1H Core Drill Dimensions CDM1H HAND-HELD CORE DRILL — SPECIFICA TIONS/DIMENSIONS Contact the MQ Sales Department for the core drill that best fits your application. Ta b l e 1 . Thread s /Ada pter s and Core Bi t Comb i nat i on s Item Part N u mber De ...
-
Multiquip CDM1H - page 12
P A GE 12 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) 1 . Hand-Grip – The CDM1H uses a plastic hand grip to guard against possible electric shock. When dr illing, hold this gr ip firmly . 2 . Reset Button – In the event of an overload press this button. Allow a sufficient amount of time for the electric motor ( ...
-
Multiquip CDM1H - page 13
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 13 CDM1H HAND-HELD CORE DRILL — PRE-SETUP Before Starting: CA UTION - Read Manual Before attempting to operate this core drill, and to avoid serious injury to personnel, always read and understand operation manual. F ailure to read and understand operation manual coul ...
-
Multiquip CDM1H - page 14
P A GE 14 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — PRE-SETUP Attaching the Cobra™ Core Bit to the Core Drill 1 . Place the core bit and core drill on a suitable workbench or area that is free of clutter dirt and debris. 2 . Before installing the core bit make sure that thepower c ...
-
Multiquip CDM1H - page 15
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 15 Applying Power to the Core Drill 1. This core drill requires 115 V A C, 60 Hz po wer . Applying power to the drill that is not specified will cause severe damage to the core drill. Always read serial plate tag before applying power to the core drill. 2. The power plu ...
-
Multiquip CDM1H - page 16
P A GE 16 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — OPERA TION Before Operating 1. Place the valve on the water source to the ON position, and then turn the water valve on the core drill (Figure 8) to the ON position (down). V erify that water is flowing smoothly and e v enly . This ...
-
Multiquip CDM1H - page 17
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 17 CDM1H HAND-HELD CORE DRILL — SHUTDO WN/MAINTENANCE Shutdown 1. Remove the power cord from the wall receptacle or power source. 2. Allow a sufficient amount of time for the core drill bit to cool before attempting to remove it from the core drill. 3 . Using the wren ...
-
Multiquip CDM1H - page 18
P A GE 18 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — TR OUBLESHOO TING G N I T O O H S E L B U O R T L L I R D E R O C . 4 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S . k c u t s s i t i B s i . c t e , e n o t s r o r a b l e e t S . T I B d n a e r o c n e ...
-
Multiquip CDM1H - page 19
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 19 CDM1H HAND-HELD CORE DRILL — WIRING DIA GRAM ...
-
Multiquip CDM1H - page 20
P A GE 20 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CORE DRILL — EXPLANA TION OF CODE IN REMARKS COLUMN The f ollowing section e xplains the diff erent symbols and remarks used in the P ar ts section of this manual. Use the help numbers f ound on the back page of the man ual if there are any questions . SAMPLE ...
-
Multiquip CDM1H - page 21
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 21 CDM1H Hand Held Core Drill 1 to 5 Units Qt y . ..... P/N ......................... Description 2 ......... CD 101534 ............... CARBON BR USH 2 ......... CD 101560 ............... POWER CORD 2 ......... CD 101551 ............... POWER SWITCH 2 ......... CD 10155 ...
-
Multiquip CDM1H - page 22
P A GE 22 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — NAMEPLA TE AND DECALS NAMEPLA TE AND DECALS ...
-
Multiquip CDM1H - page 23
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 23 CDM1H HAND-HELD CORE DRILL — NAMEPLA TE AND DECALS NAMEPLA TE AND DECALS NO . P AR T NO . P AR T NAME QTY . REMARKS 1 DCL701 D E C A L : MODEL INFORMA TION 1 2 DCL700 DECAL: CA UTION CLEAN W A TER 1 ...
-
Multiquip CDM1H - page 24
P A GE 24 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — CORE DRILL ASSY . CORE DRILL ASSY . OLD STYLE NEW STYLE 68 ...
-
Multiquip CDM1H - page 25
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 25 CORE DRILL ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 CD101501 GEAR CASE 1 2 CD101502 MAIN SHAFT 1 3 CD101503 SEAL 1 4 CD101503 SEAL 2 5 CD101505 BEARING, 6003LLU 1 6 CD101506 B E A R I N G , 6 0 0 3 Z Z 1 7 CD101507 SNAP RING, R35 1 8 CD101508 SNAP RING, S1 ...
-
Multiquip CDM1H - page 26
P A GE 26 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — CORE DRILL ASSY . CORE DRILL ASSY . OLD STYLE NEW STYLE 68 ...
-
Multiquip CDM1H - page 27
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 27 CORE DRILL ASSY . (CONTINUED) NO . P AR T NO . P AR T NAME QTY . REMARKS 4 5 CD101545 SPRING 1 4 6 CD101546 SHIFTER 1 4 7 CD101547 SCREW , M6 1 4 8 CD101548 N U T , M 6 2 4 9 CD101549 SCREW , M6 1 5 0 CD101550 SWITCH BO X ............................................. ...
-
Multiquip CDM1H - page 28
P A GE 28 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL —CARR YING CASE /T OOLS/AD APTER CARR YING CASE/T OOLS AD APTER 2 6 3 5 4 T OOL KIT 7 ...
-
Multiquip CDM1H - page 29
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 29 CDM1H HAND-HELD CORE DRILL —CARR YING CASE /T OOLS/AD APTER CARR YING CASE/T OOLS AD APTER NO . P AR T NO . P AR T NAME QTY . REMARKS 2 * 101566 2 7 MM WRENCH 1 3 * 101567 ADJUST ABLE WRENCH 1 4 * 101568 5 M M A L L E N WRENCH 1 5 * CD101572 A D APTER, 1-1/4" ...
-
Multiquip CDM1H - page 30
P A GE 30 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) TERMS AND CONDITIONS OF SALE —P AR TS P A Y MENT TERMS T er ms of payment for parts are net 3 0 days. FREIGHT P OLIC Y All parts orders will be shipped collect or prepaid with the c harges add ed to the invoice. All shipments are F .O .B. p oint of origin. Mul ...
-
Multiquip CDM1H - page 31
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 31 NO TES ...
-
Multiquip CDM1H - page 32
OPERA TION AND P AR TS MANUAL Y our Local Dealer is: HERE’S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND W HEN CALLING © COPYRIGHT 2010, MUL TIQUIP INC . Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without w ritten permission. All other tr ademarks are ...
¿Tienes una pregunta acerca de Multiquip CDM1H?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Multiquip CDM1H, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Multiquip CDM1H probablemente compartirá una forma de solucionarlo.