Français dropdown-ico

Manuel d’utilisation Lincoln Electric 200

145 pages 3.29 mb
Télécharger

Aller à la page of 145

Summary
  • Lincoln Electric 200 - page 1

    PIPELINER 200 SVM193-A July , 2009 For use with machines having Code Numbers: 1 1 1 14, 1 1316, 1 1471 10929, 10660, 10913, 1 1 136 ® SER VICE MANUAL • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 441 17-1 199 U.S.A. TEL: 888.935.3877 F AX: 216.486.1751 WEB SITE: www .lincolnelectric.com • World's ...

  • Lincoln Electric 200 - page 2

    PIPELINER® 200 SAFETY i i FOR ENGINE powered equipment. 1.a. T urn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b.Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors. _____________________ ...

  • Lincoln Electric 200 - page 3

    PIPELINER® 200 SAFETY ii ii FUMES AND GASES can be dangerous. 5.a. Welding may produce fumes and gases hazardous to health. Avoid breathing these fumes and gases.When welding, keep your head out of the fume. Use enough ventilation and/or exhaust at the arc to keep fumes and gases away from the breathing zone. When welding with electrodes which req ...

  • Lincoln Electric 200 - page 4

    PIPELINER® 200 SAFETY iii iii Jan ʻ09 FOR ELECTRICALL Y powered equipment. 8.a. T urn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer ʼs recommendations. 8.c. Ground the equipment in accor ...

  • Lincoln Electric 200 - page 5

    SAFETY iv iv PIPELINER® 200 Mar ʻ93 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L ʼArc 1. Protegez-vous contre la secousse élec ...

  • Lincoln Electric 200 - page 6

    I I - MASTER T ABLE OF CONTENTS FOR ALL SECTIONS - PIPELINER® 200 Page S a f e t y ........................................................................... i - i v Installation (Kubota V2203M) (K6090-1 1) ......................................... Section A Installation (Perkins 104.22) (K6090-9) ......................................... Section ...

  • Lincoln Electric 200 - page 7

    T ABLE OF CONTENTS - INST ALLA TION SECTION A-1 A-1 PIPELINER® 200D KUBOT A I n s t a l l a t i o n ............................................................................. A - 1 T e c h n i c a l S p e c i f i c a t i o n s ................................................................ A - 2 G e n e r a l D e s c r i p t i o n& D e s i ...

  • Lincoln Electric 200 - page 8

    INST ALLA TION A-2 A-2 PIPELINER® 200D KUBOT A TECHNICAL SPECIFICA TIONS - PIPELINER® 200D KUBOT A (K6090-1 1) INPUT - DIESEL ENGINE RA TED OUTPUT @ 104°F(40°C) - WELDER HEIGHT WIDTH DEPTH WEIGHT 45.50 (2) in. 24.00 in. 68.00 in. 1302 lbs. (1 156 mm) (610 mm) (1727 mm) (592 kg) RA TED OUTPUT @ 104°F(40°C) - GENERA TOR DESCRIPTION RA TED DC OU ...

  • Lincoln Electric 200 - page 9

    INST ALLA TION A-3 A-3 PIPELINER® 200D KUBOT A ENGINE IDLER The Pipeliner® 200D KUBOT A is equipped with an electronic automatic engine idler . It automatically increases and decreases engine speed when starting and stopping welding or using auxiliary power . A built- in time delay permits changing electrodes before the engine slows to its low id ...

  • Lincoln Electric 200 - page 10

    INST ALLA TION A-4 A-4 PIPELINER® 200D KUBOT A PRE-OPERA TION INST ALLA TION EXHAUST SP ARK ARRESTER Some federal, state or local laws may require that engines be equipped with exhaust spark arresters when they are operated in certain locations where unarrested sparks may present a fire hazard. The standard muffler included with this welder does n ...

  • Lincoln Electric 200 - page 11

    INST ALLA TION A-5 A-5 PRE-OPERA TION SERVICE READ the engine operating and maintenance instruc- tions supplied with this machine. OIL This unit is supplied from the factory with the engine crankcase filled with a high quality SAE 10W/30 oil. This oil should be acceptable for most typical ambient temperatures. Consult the engine operation manual fo ...

  • Lincoln Electric 200 - page 12

    INST ALLA TION A-6 A-6 PIPELINER® 200D KUBOT A Battery Charging The PIPELINER® 200D KUBOT A is equipped with a wet charged battery . The charging current is automat- ically regulated when the battery is low (after starting the engine) to a trickle current when the battery is fully charged. When replacing, jumping or otherwise connecting the batte ...

  • Lincoln Electric 200 - page 13

    T ABLE OF CONTENTS - OPERA TION SECTION B-1 B-1 PIPELINER® 200D KUBOT A O p e r a t i o n .............................................................................. B - 1 E n g i n e O p e r a t i o n ..................................................................... B - 2 W e l d e r O p e r a t i o n ...................................... ...

  • Lincoln Electric 200 - page 14

    OPERA TION B-2 B-2 ENGINE OPERA TION Operate the welder with the doors closed. Leaving the doors open changes the designed air flow and can cause overheating. ST ARTING THE PIPELINER® 200D KUBOT A V2203M DIESEL ENGINE 1. T urn the “IDLER” switch to “HIGH”. 2. T urn the “IGNITION” switch to “ON”. 3. Press the Glow Plug button for 20 ...

  • Lincoln Electric 200 - page 15

    OPERA TION B-3 B-3 PIPELINER® 200D KUBOT A WELDER OPERA TION ------------------------------------------------------------------------ DUTY CYCLE The NEMA output rating of the PIPELINER® 200D KUBOT A is 200 amperes at 28 arc volts on a 60% duty cycle (consult Specifications in this manual for alternate ratings). Duty cycle is based on a ten minute ...

  • Lincoln Electric 200 - page 16

    OPERA TION B-4 B-4 PIPELINER® 200D KUBOT A IDLER OPERA TION Start the engine with the “Idler” switch in the “High” position. Allow it to run at high idle speed for several minutes to warm the engine. See Specifications for operating speeds. The idler is controlled by the “Idler” toggle switch on the welder control panel. The switch has ...

  • Lincoln Electric 200 - page 17

    T ABLE OF CONTENTS - ACCESSORIES SECTION C-1 C-1 PIPELINER® 200D KUBOT A A c c e s s o r i e s............................................................................ C - 1 O p t i o n a l F e a t u r e s..................................................................... C - 2 Return to Master TOC Return to Master TOC Return to Master TOC Re ...

  • Lincoln Electric 200 - page 18

    ACCESSORIES C-2 C-2 PIPELINER® 200D KUBOT A WIRE FEED OPTIONS Wire Feed Module (K623-1) - Provides constant volt- age (CV) output with improved arc stability for Innershield welding. Excellent for MIG welding. Recommended wire feeders are the LN-7, LN-23P and LN-25. (Factory installed on the K1643-6). LN-15 Wire Feeder (K1870-1,-2)- Portable CC/CV ...

  • Lincoln Electric 200 - page 19

    T ABLE OF CONTENTS - MAINTENANCE SECTION D-1 D-1 PIPELINER® 200D KUBOT A M a i n t e n a n c e ........................................................................... D - 1 Safety Precautions, Bearings, Commutator & Brushes, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-2 I d l e r M a i n t e n a n c e ... ...

  • Lincoln Electric 200 - page 20

    MAINTENANCE D-2 D-2 SAFETY PRECAUTIONS GENERAL INSTRUCTIONS 1. Blow out the welder and controls with an air hose at least once every two months. In particularly dirty locations, this cleaning may be necessary once a week. Use low pressure air to avoid driving dirt into the insulation. 2. “Current Range Selector” contacts should not be greased. ...

  • Lincoln Electric 200 - page 21

    MAINTENANCE D-3 D-3 PIPELINER® 200D KUBOT A Replace brushes when they wear within 1/4”(3.5mm) of the pigtail. A complete set of replacement brushes should be kept on hand. Lincoln brushes have a curved face to fit the commutator . Have an experi- enced maintenance man seat these brushes by lightly stoning the commutator as the armature rotates a ...

  • Lincoln Electric 200 - page 22

    MAINTENANCE D-4 D-4 PIPELINER® 200D KUBOT A If necessary use shorter periods. These preventive m aintenance periods apply to average conditions of operation. Above operations to be carried out by trained personnel with reference to the worksh op manual where necessary. (3) Fill slowly! Ensure correct quantity is used. (2) Consult Engine Operators ...

  • Lincoln Electric 200 - page 23

    MAINTENANCE D-5 D-5 PIPELINER® 200D KUBOT A 9 9 8 8 1 1 5 5 7 7 4 4 6 6 3 3 6 6 9 9 2 2 Figure D.2 - Major Component Location 1. Case Front Assembly 2. Engine Assembly 3. Exciter Frame, Armature Assembly 4. Generator Frame, Armature & Coupling 5. Fuel T ank Assembly 6. Generator & Exciter Brush Holder Assemblies 7. Base & Lift Bale Ass ...

  • Lincoln Electric 200 - page 24

    NOTES D-6 D-6 PIPELINER® 200D KUBOT A Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 25

    T ABLE OF CONTENTS - INST ALLA TION SECTION AA-1 AA-1 PIPELINER® 200D PERKINS I n s t a l l a t i o n ........................................................................... A A - 1 T e c h n i c a l S p e c i f i c a t i o n s ............................................................... A A - 2 S a f e t y P r e c a u t i o n s ........... ...

  • Lincoln Electric 200 - page 26

    INST ALLA TION AA-2 AA-2 DC CURRENT RANGE Fine Adjustment in each Range 40-300 Amps DUTY CYCLE* 60% RA TED DC OUTPUT VOL TS @ RA TED AMPS Lincoln Plus Rating 40V @ 200A NEMA Rating 28V @ 200A PIPELINER® 200D PERKINS 1. Output rating in watts is equivalent to volt-amperes at unity power factor . Output voltage is within ± 10% at all loads up to ra ...

  • Lincoln Electric 200 - page 27

    INST ALLA TION AA-3 AA-3 Do not attempt to use this equipment until you have thoroughly read the engine manufacturer ʼ s manual supplied with your welder . It includes important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists. -------------------------------------------------------------------- ...

  • Lincoln Electric 200 - page 28

    INST ALLA TION AA-4 AA-4 PIPELINER® 200D PERKINS POLARITY CONTROL AND CABLE SIZES With the engine off, route the electrode and work cables through the strain relief bracket on the base and connect to the studs located below the fuel tank mount- ing rail. (see size recommendations below). For Positive polarity , connect the electrode cable to the t ...

  • Lincoln Electric 200 - page 29

    INST ALLA TION AA-5 AA-5 PIPELINER® 200D PERKINS OIL This unit is supplied from the factory with the engine crankcase filled with a high quality SAE 10W/30 oil. This oil should be acceptable for most typical ambient temperatures. Consult the engine operation manual for specific engine manufacturers recommendations. Upon receipt of the welder , che ...

  • Lincoln Electric 200 - page 30

    NOTES AA-6 AA-6 PIPELINER® 200D PERKINS Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 31

    T ABLE OF CONTENTS - OPERA TION SECTION BB-1 BB-1 PIPELINER® 200D PERKINS O p e r a t i o n ............................................................................ B B - 1 S a f e t y P r e c a u t i o n s &D e s i g n S u m m a r y .................................................. B B - 2 E n g i n e O p e r a t i o n &C o l d W e a ...

  • Lincoln Electric 200 - page 32

    The Pipeliner® 200D has a current range of 40-300 DC amps with output ratings as follows: RA TED OUTPUT DUTY CYCLE 200A @ 28V 60% 200A @ 40V 60% The unit is also capable of providing 1.80 kw of 120V DC auxiliary power at 35% duty cycle maximum. This unit uses the PERKINS 104.22 Industrial water cooled diesel engine. DESIGN SUMMAR Y Control Panel B ...

  • Lincoln Electric 200 - page 33

    OPERA TION BB-3 BB-3 PIPELINER® 200D PERKINS Cranking System A 12V electric starter is standard. Air Cleaner Heavy duty two-stage dry type Exhaust A muffler and stainless steel exhaust outlet pipe are standard. Engine Hour Meter A meter to record the hours of operation. ENGINE OPERA TION Operate the welder with the doors closed. Leaving the doors ...

  • Lincoln Electric 200 - page 34

    OPERA TION BB-4 BB-4 ENGINE BREAK-IN Lincoln Electric selects high quality , heavy-duty indus- trial engines for the portable welding machines we offer . While it is normal to see a small amount of crankcase oil consumption during initial operation, excessive oil use, wetstacking (oil or tar like substance at the exhaust port), or excessive smoke i ...

  • Lincoln Electric 200 - page 35

    OPERA TION BB-5 BB-5 PIPELINER® 200D PERKINS When a forceful “digging” arc is required, usually for vertical and overhead welding, use a higher “Current Range Selector” setting and lower open circuit voltage. For example: to obtain 175 amps and a forceful arc, set the “Current Range Selector” to the 240-160 position and the “Fine Cur ...

  • Lincoln Electric 200 - page 36

    NOTES BB-6 BB-6 PIPELINER® 200D PERKINS Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 37

    T ABLE OF CONTENTS - ACCESSORIES SECTION CC-1 CC-1 PIPELINER® 200D PERKINS A c c e s s o r i e s .......................................................................... C C - 1 O p t i o n a l F e a t u r e s ................................................................ C C - 2 Return to Master TOC Return to Master TOC Return to Master TOC R ...

  • Lincoln Electric 200 - page 38

    ACCESSORIES CC-2 CC-2 PIPELINER® 200D PERKINS OPTIONAL FEA TURES (Field Installed) Accessory Set (K704) - Includes electrode and work cables, headshield, work clamp and electrode holder . Remote Control Kit (K924-5) - Contains a remote control rheostat and 100 ft (30.5m) cable for adjusting the OCV at the welding site. Remote Control Kit (K2464-1) ...

  • Lincoln Electric 200 - page 39

    T ABLE OF CONTENTS - MAINTENANCE SECTION DD-1 DD-1 PIPELINER® 200D PERKINS M a i n t e n a n c e .......................................................................... D D - 1 S a f e t y P r e c a u t i o n s .................................................................. D D - 2 Bearings, Commutator & Brushes, Idler Control Maintenanc ...

  • Lincoln Electric 200 - page 40

    MAINTENANCE DD-2 DD-2 PIPELINER® 200D PERKINS SAFETY PRECAUTIONS GENERAL INSTRUCTIONS 1. Blow out the welder and controls with an air hose at least once every two months. In particularly dirty locations, this cleaning may be necessary once a week. Use low pressure air to avoid driving dirt into the insulation. 2. “Current Range Selector” conta ...

  • Lincoln Electric 200 - page 41

    MAINTENANCE DD-3 DD-3 PIPELINER® 200D PERKINS BEARINGS This welder is equipped with a double-shielded ball bearing having sufficient grease to last indefinitely under normal service. Where the welder is used con- stantly or in excessively dirty locations, it may be nec- essary to add one-half ounce of grease per year . A pad of grease one inch wid ...

  • Lincoln Electric 200 - page 42

    MAINTENANCE DD-4 DD-4 PIPELINER® 200D PERKINS I EVERY 400 HOURS OR 12 MONTHS EVERY 200 HOURS OR 6 MONTHS EVERY 100 HOURS OR 3 MONTHS FIRST SERVICE-(20 / 50 HOURS) EVERY DAY OR EVERY 8 HOURS Perkins #140517000 If necessary use shorter periods. These preventive maintenance periods apply to average conditions of operation. Perkins #26560017 TYPE OR Q ...

  • Lincoln Electric 200 - page 43

    MAINTENANCE DD-5 DD-5 PIPELINER® 200D PERKINS 10 9 1 5 7 4 6 3 10 2 8 Figure DD.2 - Major Component Location 1. Case Front Assembly 2. Engine Assembly 3. Exciter Frame, Armature Assembly 4. Generator Frame, Armature & Coupling 5. Fuel T ank Assembly 6. Generator & Exciter Brush Holder Assemblies 7. Base & Lift Bale Assembly 8. Idler So ...

  • Lincoln Electric 200 - page 44

    NOTES DD-6 DD-6 PIPELINER® 200D PERKINS Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 45

    T ABLE OF CONTENTS - INST ALLA TION SECTION AAA-1 AAA-1 PIPELINER® 200G I n s t a l l a t i o n .......................................................................... A A A - 1 T e c h n i c a l S p e c i f i c a t i o n s ............................................................. A A A - 2 S a f e t y P r e c a u t i o n s ................ ...

  • Lincoln Electric 200 - page 46

    INST ALLA TION AAA-2 AAA-2 DC CURRENT RANGE Fine Adjustment in each Range 40-300 Amps DUTY CYCLE 60% 60% RA TED DC OUTPUT* VOL TS @ RA TED AMPS Lincoln Plus Rating 40V @ 200A NEMA Rating 28V @ 200A PIPELINER® 200G 1. Output rating in watts is equivalent to volt-amperes at unity power factor . Output voltage is within ± 10% at all loads up to rate ...

  • Lincoln Electric 200 - page 47

    INST ALLA TION AAA-3 AAA-3 Do not attempt to use this equipment until you have thoroughly read the engine manufacturer ʼ s manual supplied with your welder . It includes important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists. ------------------------------------------------------------------ ...

  • Lincoln Electric 200 - page 48

    INST ALLA TION AAA-4 AAA-4 PIPELINER® 200G POLARITY CONTROL AND CABLE SIZES With the engine off, route the electrode and work cables through the strain relief bracket on the base and connect to the studs located below the fuel tank mount- ing rail. (see size recommendations below). For Positive polarity , connect the electrode cable to the termina ...

  • Lincoln Electric 200 - page 49

    INST ALLA TION AAA-5 AAA-5 PIPELINER® 200G PRE-OPERA TION SERVICE READ the engine operating and maintenance instruc- tions supplied with this machine. ------------------------------------------------------------------------ OIL This unit is supplied from the factory with the engine crankcase filled with a high quality SAE 10W/30 oil. This oil shou ...

  • Lincoln Electric 200 - page 50

    NOTES AAA-6 AAA-6 PIPELINER® 200G Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 51

    T ABLE OF CONTENTS - OPERA TION SECTION BBB-1 BBB-1 PIPELINER® 200G O p e r a t i o n ........................................................................... B B B - 1 S a f e t y P r e c a u t i o n s &D e s i g n S u m m a r y ................................................. B B B - 2 E n g i n e / W e l d e r O p e r a t i o n ........ ...

  • Lincoln Electric 200 - page 52

    OPERA TION BBB-2 BBB-2 SAFETY PRECAUTIONS Do not attempt to use this equipment until you have thoroughly read the engine manufacturer ʼ s manual supplied with your welder . It includes important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists. --------------------------------------------------- ...

  • Lincoln Electric 200 - page 53

    OPERA TION BBB-3 BBB-3 PIPELINER® 200G Cranking System A 12V electric starter is standard. Air Cleaner Heavy duty two-stage dry type Exhaust A muffler and stainless steel exhaust outlet pipe are standard. Engine Hour Meter A meter to record the hours of operation. High Idle RPM (OCV) Adjustment- A potentiometer is mounted on the output rail that a ...

  • Lincoln Electric 200 - page 54

    OPERA TION BBB-4 BBB-4 PIPELINER® 200G CONTROL OF WELDING CURRENT DO NOT TURN THE “CURRENT RANGE SELEC- TOR” WHILE WELDING because the current may arc between the contacts and damage the switch. ------------------------------------------------------------------------ The “Current Range Selector” provides five overlap- ping current ranges. ...

  • Lincoln Electric 200 - page 55

    T ABLE OF CONTENTS - ACCESSORIES SECTION CCC-1 CCC-1 A c c e s s o r i e s ......................................................................... C C C - 1 O p t i o n a l E q u i p m e n t& R e m o t e C o n t r o l s ................................................. C C C - 2 PIPELINER® 200G Return to Master TOC Return to Master TOC Retur ...

  • Lincoln Electric 200 - page 56

    ACCESSORIES CCC-2 CCC-2 PIPELINER® 200G OPTIONAL EQUIPMENT (FIELD INST ALLED) (K704) Accessory Set Includes 35 ft (10.7m) electrode and 30 ft (9.1m) work cables, headshield, work clamp, and electrode holder . Pipe Thawing with an arc welder can cause fire, explosion, damage to electric wiring or to the arc welder if done improperly . The use of an ...

  • Lincoln Electric 200 - page 57

    T ABLE OF CONTENTS - MAINTENANCE SECTION DDD-1 DDD-1 PIPELINER® 200G M a i n t e n a n c e ......................................................................... D D D - 1 S a f e t y P r e c a u t i o n s ................................................................. D D D - 2 Bearings, Commutator & Brushes, Idler Control Maintenance . ...

  • Lincoln Electric 200 - page 58

    MAINTENANCE DDD-2 DDD-2 PIPELINER® 200G SAFETY PRECAUTIONS GENERAL INSTRUCTIONS 1. Blow out the welder and controls with an air hose at least once every two months. In particularly dirty locations, this cleaning may be necessary once a week. Use low pressure air to avoid driving dirt into the insulation. 2. “Current Range Selector” contacts sh ...

  • Lincoln Electric 200 - page 59

    MAINTENANCE DDD-3 DDD-3 PIPELINER® 200G BEARINGS This welder is equipped with a double-shielded ball bearing having sufficient grease to last indefinitely under normal service. Where the welder is used con- stantly or in excessively dirty locations, it may be nec- essary to add one-half ounce of grease per year . A pad of grease one inch wide, one ...

  • Lincoln Electric 200 - page 60

    MAINTENANCE DDD-4 DDD-4 PIPELINER® 200G I EVERY 600 HOURS OR 12 MONTHS E VERY 200 HOURS OR 6 MONTHS EVERY 100 HOURS OR 3 MONTHS FIRST SERVICE-(50 HOURS) E VERY DAY OR EVERY 8 HOURS If necessary use shorter periods. These preventive maintenance periods apply to average conditions of operation. PSI #32500292 AC PF25 T YPE OR QUANTITY Above operation ...

  • Lincoln Electric 200 - page 61

    MAINTENANCE DDD-5 DDD-5 PIPELINER® 200G 9 8 1 5 2 7 9 4 6 3 6 Figure DDD.1 - Major Component Location 1. Case Front Assembly 2. Engine Assembly 3. Exciter Frame, Armature Assembly 4. Generator Frame, Armature & Coupling 5. Fuel T ank Assembly 6. Generator & Exciter Brush Holder Assemblies 7. Base & Lift Bale Assembly 8. Radiator Assemb ...

  • Lincoln Electric 200 - page 62

    NOTES DDD-6 DDD-6 PIPELINER® 200G Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 63

    T ABLE OF CONTENTS-THEOR Y OF OPERA TION SECTION E-1 E-1 PIPELINER® 200 T h e o r y o f O p e r a t i o n ..................................................................... E - 1 G e n e r a l D e s c r i p t i o n ................................................................... E - 2 E n g i n e C o n t r o l................................ ...

  • Lincoln Electric 200 - page 64

    THEOR Y OF OPERA TION GENERAL DESCRIPTION The PIPELINER® 200 is a heavy duty , engine driven, DC arc welding power source capable of providing con- stant current output for stick welding or DC TIG weld- ing. Also, a total of 1750 watts of auxiliary power is available at the 120VDC receptacle. The PIPELINER® 200 is manufactured with all copper win ...

  • Lincoln Electric 200 - page 65

    THEOR Y OF OPERA TION E-3 E-3 PIPELINER® 200 BA TTER Y , ST ARTER, ENGINE AL TERNA TOR, OIL, & TEMPERA TURE SWITCH CIRCUITS The 12VDC battery powers the starter motor and, through the ignition switch, the engine ignition circuitry (gas models only), the engine alternator , the engine control protection modules and associated circuits. See the ...

  • Lincoln Electric 200 - page 66

    THEOR Y OF OPERA TION E-4 E-4 PIPELINER® 200 BA TTER Y , ST ARTER, ENGINE AL TERNA TOR, OIL, & TEMPERA TURE SWITCH CIRCUITS The 12VDC battery powers the starter motor and, through the ignition switch, the engine ignition circuitry (gas models only), the engine alternator , the engine control protection modules and associated circuits. See the ...

  • Lincoln Electric 200 - page 67

    THEOR Y OF OPERA TION E-5 E-5 PIPELINER® 200 BA TTER Y , ST ARTER, ENGINE AL TERNA TOR, OIL, & TEMPERA TURE SWITCH CIRCUITS The 12VDC battery powers the starter motor and, through the ignition switch, the engine ignition circuitry (gas models only), the engine alternator , the engine control protection modules and associated circuits. See the ...

  • Lincoln Electric 200 - page 68

    THEOR Y OF OPERA TION E-6 E-6 PIPELINER® 200 ENGINE, MAIN GENERA TOR ARMA TURE & FRAME AND DC EXCITER EXCIT A TION (FLASHING) The main generator armature and the exciter armature are mechanically coupled to the engine. When the engine is started and running, the residual magnetism that is stored in the exciter pole pieces is induced upon the e ...

  • Lincoln Electric 200 - page 69

    THEOR Y OF OPERA TION E-7 E-7 PIPELINER® 200 DC GENERA TOR MACHINES The armature winding of a DC generator is located on the rotating member . Current is conducted from it by means of carbon brushes. The field winding is located in the stator , which is stationary and excited by direct current. The armature coil sides are placed at opposite points ...

  • Lincoln Electric 200 - page 70

    NOTES E-8 E-8 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 71

    T ABLE OF CONTENTS - TROUBLESHOOTING & REP AIR F-1 F-1 PIPELINER® 200 T r o u b l e s h o o t i n g a n d R e p a i r .............................................................. F - 1 H o w t o U s eT r o u b l e s h o o t i n g G u i d e ....................................................... F - 2 P C B o a r dT r o u b l e s h o o t i n ...

  • Lincoln Electric 200 - page 72

    TROUBLESHOOTING & REP AIR F-2 F-2 PIPELINER® 200 This T roubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below . Step 1. LOCA TE PROBLEM (SYMPT OM). Look under the column labeled “PROBLEM (SYMPTOMS)”. This column describes pos- sible symptoms that th ...

  • Lincoln Electric 200 - page 73

    TROUBLESHOOTING & REP AIR F-3 F-3 PIPELINER® 200 Sometimes machine failures appear to be due to PC board failures. These problems can sometimes be traced to poor electrical connections. T o avoid prob- lems when troubleshooting and replacing PC boards, please use the following procedure: 1. Determine to the best of your technical ability that ...

  • Lincoln Electric 200 - page 74

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric 200 - page 75

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric 200 - page 76

    POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubleshooting assistance before you proceed. Call 1-888-935-3877. CAUTION 1. Check the welding cables for loos ...

  • Lincoln Electric 200 - page 77

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric 200 - page 78

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric 200 - page 79

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric 200 - page 80

    WELDING PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical trouble ...

  • Lincoln Electric 200 - page 81

    TROUBLESHOOTING & REP AIR F-11 F-11 PIPELINER® 200 Observe all Safety Guidelines detailed throughout this manual LIGHT CODE F AILURE DETECTED POSSIBLE CAUSE - CORRECTIVE MEASURE LONG 1, SHORT 1 RPM IS OVER 1 15% OF RA TED RPM (2070 RPM) ACTUA TOR IS STUCK - REMOVE ACTUA TOR AND VERIFY PLUNGER PULLS IN WHEN ENERGIZED LONG 1, SHORT 2 LOW OIL PRE ...

  • Lincoln Electric 200 - page 82

    NOTES F-12 F-12 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 83

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 84

    DC EXCITER TEST (CONTINUED) TROUBLESHOOTING & REP AIR F-14 F-14 PIPELINER® 200 SERIES COIL CONNECTION POINT (NEGA TIVE) POSITIVE FIGURE F .1 – 120VDC RECEPT ACLE TEST PROCEDURE 1. T urn off the engine and remove all external loads to the welder terminals and auxiliary receptacle. MOVING P ARTS can injure. • Remove guards only when necessar ...

  • Lincoln Electric 200 - page 85

    DC EXCITER TEST (CONTINUED) TROUBLESHOOTING & REP AIR F-15 F-15 PIPELINER® 200 EXITER COVER W ARRANTY CHECK VOLTAGE A T BRUSH HOLDERS HERE (RIGHT SIDE IS +) + FIGURE F .2 – EXCITER COVER REMOVAL 4. T urn off the engine. Using the 3/8” nut driver , remove the exciter cover . See Figure F .2. 5. Start the engine. Using the volt/ohmmeter , ca ...

  • Lincoln Electric 200 - page 86

    TROUBLESHOOTING & REP AIR F-16 F-16 PIPELINER® 200 WHITE FLEX LEAD SMALL FLEX LEAD SOLID LEAD WARRANTY FIGURE F .3 – BRUSH HOLDER LEADS SHUNT COIL AND SERIES COIL RESIST ANCE TESTS 7. T urn the engine OFF . 8. Using the 3/8" nut driver , disconnect the two leads from the left side brush holder . See Figure F .3. Separate the two leads. ...

  • Lincoln Electric 200 - page 87

    TROUBLESHOOTING & REP AIR F-17 F-17 PIPELINER® 200 Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, plea ...

  • Lincoln Electric 200 - page 88

    TROUBLESHOOTING & REP AIR F-18 F-18 PIPELINER® 200 IDLER SOLENOID TEST (continued) FIGURE F .4 – IDLER SOLENOID CONNECTIONS QUICK CONNECT LEADS TEST PROCEDURE 1. T urn the engine OFF . 2. Unlatch and secure the right side door . 3. Locate the idler solenoid and the two leads with quick connects. See Figure F .4. 4. Disconnect the two solenoi ...

  • Lincoln Electric 200 - page 89

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 90

    TROUBLESHOOTING & REP AIR F-20 F-20 PIPELINER® 200 MAIN GENERA T OR SHUNT FIELD WINDING TEST (continued) FIGURE F .5 – PLUG P10 LOCA TION PLUG P10 TEST PROCEDURE 1. T urn the engine OFF . 2. Unlatch, lift and secure the right side door . 3. Locate plug P10. See Figure F .5. 4. Remove plug P10. Return to Section TOC Return to Section TOC Retu ...

  • Lincoln Electric 200 - page 91

    TROUBLESHOOTING & REP AIR F-21 F-21 PIPELINER® 200 MAIN GENERA T OR SHUNT FIELD WINDING TEST (continued) FIGURE F .6 – PLUG P10 PIN ASSIGNMENTS PIN 3 PIN 5 TA B 5. Locate the blue (U) (pin 3) and the brown (N) (pin 5) leads in the harness plug. See Figure F .6. 6. Using the volt/ohmmeter , measure the resis- tance between the blue and the br ...

  • Lincoln Electric 200 - page 92

    NOTES F-22 F-22 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 93

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 94

    TROUBLESHOOTING & REP AIR F-24 F-24 PIPELINER® 200 FLASHING THE FIELDS (continued) FIGURE F .7 – EXCITER COVER REMOV AL EXITER COVER PROCEDURE 1. T urn the engine OFF . 2. Using a 3/8” Nutdriver, remove the exciter cover . See Figure F .7. Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Mas ...

  • Lincoln Electric 200 - page 95

    TROUBLESHOOTING & REP AIR F-25 F-25 PIPELINER® 200 FLASHING THE FIELDS (continued) FIGURE F .8 - BRUSH HOLDER/BA TTER Y JUMPER CONNECTIONS + RAISE EXCITER BRUSH OFF COMMUT AT OR TO POSITIVE BA TTERY TERMINAL TO NEGATIVE BA TTERY TERMINAL WARRANTY 3. Raise one exciter brush off the armature commuta- tor . 4. Using the jumper leads and the 12VDC ...

  • Lincoln Electric 200 - page 96

    NOTES F-26 F-26 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 97

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 98

    ENGINE AL TERNA TOR TEST (CONTINUED) TROUBLESHOOTING & REP AIR F-28 F-28 PIPELINER® 200 Alternator Output Leads BACK OF AL TERNA TOR FIGURE F .9 - AL TERNA TOR LEAD LOCA TIONS TEST PROCEDURE 1. T urn the engine off. 2. Open the engine access door and check the voltage at the battery terminals. It should be approximately 12 volts DC. 3. Attach ...

  • Lincoln Electric 200 - page 99

    OIL PRESSURE - TEMPERA TURE SWITCH TEST W ARNING TROUBLESHOOTING & REP AIR F-29 F-29 PIPELINER® 200 Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . Fo ...

  • Lincoln Electric 200 - page 100

    G WK OIL SWITCH / SENDER S17026-3 TEMP SW . / SENDER S25162 1 /2-14 NPT 1/4" SP ADE TERMINAL 3/16" SP ADE TERMINAL G W G ND .19 .03 + - FIGURE F .10 - SWITCH WK TERMINAL TO GROUND TO CASE A T 6 +/-2 PSI. OTHERWISE TERMINAL TO BE OPEN OIL PRESSURE - TEMPERA TURE SWITCH TEST (CONTINUED) PROCEDURE 1. With the engine not running locate the Oi ...

  • Lincoln Electric 200 - page 101

    TROUBLESHOOTING & REP AIR F-31 F-31 PIPELINER® 200 OIL PRESSURE - TEMPERA TURE SWITCH TEST (CONTINUED) PROCEDURE 1. With the engine not running, and at room temperature, locate the T emperature Switch/Sender . 2. Remove the two leads from the switch. 3. Using the ohmmeter check the resistance from terminal WK to case ground. This is a normal- ...

  • Lincoln Electric 200 - page 102

    NOTES F-32 F-32 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 103

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 104

    B OL T / NUT (4) “ L ” DOOR H OOKS (4) FIGURE F .1 1 - CASE COVERS CURRENT SENSOR PCB TEST (CONTINUED) PROCEDURE 1. T urn the engine off. 2. Remove the four nuts and bolts holding the case top and doors assembly to the welder frame. See Figure F .1 1. 3. Remove the rubber gasket from the top. Carefully lift up and remove the “L” shaped door ...

  • Lincoln Electric 200 - page 105

    FIGURE F .12 - CURRENT SENSING PCB CURRENT SENSOR PCB TEST (CONTINUED) TROUBLESHOOTING & REP AIR F-35 F-35 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 106

    NOTES F-36 F-36 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 107

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 108

    BLOWER P ADDLE MARK FIGURE F .13 - BLOWER P ADDLE MARK LOCA TION ENGINE THROTTLE ADJUSTMENT TEST (CONTINUED) (PERKINS ONL Y) PROCEDURE Strobe T ach Method 1. T urn the engine off. 2. Unlatch, lift and secure the right side door . Note: Latches are located at both ends of the door . 3. Using a white or red marking pencil, place a mark on one of the ...

  • Lincoln Electric 200 - page 109

    ENGINE THROTTLE ADJUSTMENT TEST (CONTINUED) (PERKINS ONL Y) PROCEDURE 6. If either of the readings is incorrect, adjust the throt- tle as follows: Adjust HIGH IDLE: The Engine is Preset at factory . Contact Perkins @ 1-888-737-5364 or www .perkins.com Adjust LOW IDLE: First make sure there is no load on the machine. Set the IDLE switch to AUT O and ...

  • Lincoln Electric 200 - page 110

    IDLER ROD IDLER ADJUSTMENT L OCK NUT BALL JOINT FIGURE F .14 – SOLENOID LOCA TION ENGINE THROTTLE ADJUSTMENT TEST (CONTINUED) (PERKINS ONL Y) TROUBLESHOOTING & REP AIR F-40 F-40 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 111

    TROUBLESHOOTING & REP AIR F-41 F-41 PIPELINER® 200 This is the typical auxiliary output voltage generated from a properly operating machine. Note that each vertical division represents 50 volts and that each horizontal division represents 2 milliseconds in time. Note: Scope probes connected at machine 1 15VDC receptacle. SCOPE SETTINGS V olts/ ...

  • Lincoln Electric 200 - page 112

    TROUBLESHOOTING & REP AIR F-42 F-42 PIPELINER® 200 This is the typical DC welding output voltage generated from a properly operating machine. Note that each vertical division represents 50 volts and that each horizontal division represents 5 milliseconds in time. Note: Scope probes connected at machine output terminals. SCOPE SETTINGS V olts/D ...

  • Lincoln Electric 200 - page 113

    TROUBLESHOOTING & REP AIR F-43 F-43 PIPELINER® 200 This is the typical DC welding output voltage generated from a properly operating machine. Note that each vertical division represents 20 volts and that each horizontal division represents 5 milliseconds in time. The machine was loaded with a resistance grid bank. Note: Scope probes connected ...

  • Lincoln Electric 200 - page 114

    NOTES F-44 F-44 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 115

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 116

    DC EXCITER ARMA TURE & FIELD COILS REMOV AL AND REPLACEMENT PROCEDURE TROUBLESHOOTING & REP AIR F-46 F-46 PIPELINER® 200 FIGURE F .15 – EXCITER COVER REMOV AL ARMA TURE BRUSH HOLDER ASSEMBL Y (2) EXITER FRAME POLE PIECE BOL TS (4) EXITER COVER ARMA TURE LOCKING NUT FLA T W ASHER SLEEVE COLLAR PROCEDURE DC Exciter Armature Removal Procedu ...

  • Lincoln Electric 200 - page 117

    DC EXCITER ARMA TURE & FIELD COILS REMOV AL AND REPLACEMENT PROCEDURE TROUBLESHOOTING & REP AIR F-47 F-47 PIPELINER® 200 Field Coils Removal Procedure 1. Perform the DC Exciter Armature Removal Procedure. 2. Using the 3/8” wrench, remove the leads from the brush holder . Note lead placement for reassembly . 3. Using the 1/2” wrench, re ...

  • Lincoln Electric 200 - page 118

    NOTES F-48 F-48 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 119

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE W ARNING TROUBLESHOOTING & REP AIR F-49 F-49 PIPELINER® 200 Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your fac ...

  • Lincoln Electric 200 - page 120

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-50 F-50 PIPELINER® 200 FIGURE F .16 – BA TTERY P ANEL REMOV AL NEGA TIVE BA TTER Y CABLE PROCEDURE 1. T urn the engine OFF . 2. Using the 7/16” wrench, remove the two bolts and washers and partially slide out the battery mounting panel. See Fi ...

  • Lincoln Electric 200 - page 121

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-51 F-51 PIPELINER® 200 FIGURE F .17 – TOP AND DOORS ASSEMBL Y DET AILS BOL T / NUT (4) 'L' DOOR HOOKS (4) 4. Using the 1/2” wrench, remove the four nuts and bolts holding the case top and doors assembly to the welder frame. Remove th ...

  • Lincoln Electric 200 - page 122

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-52 F-52 PIPELINER® 200 FIGURE F .18 – FUEL T ANK MOUNTING DET AILS BOL TS / NUTS / W ASHERS (4) FUEL T ANK FUEL BOWL RAILS FUEL LINE 5. Perform the DC Exciter Armature Removal Procedure. 6. T urn off the fuel supply at the fuel bowl and remove t ...

  • Lincoln Electric 200 - page 123

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-53 F-53 PIPELINER® 200 FIGURE F .19 – SELECTOR SWITCH LEAD REMOVAL SELECTOR SWITCH TERMINAL LEAD (5) A C B D E 9. Using the 1/2” wrench, remove the five heavy flex leads from the selector switch terminals. Label the leads for reassembly . See ...

  • Lincoln Electric 200 - page 124

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-54 F-54 PIPELINER® 200 FIGURE F .21 – CHOKE CONTROL CABLE REMOVAL LOOSEN HERE CHOKE CABLE 12. Using the slot head screw driver , remove the choke control cable from the engine carbure- tor assembly . Mark cable replacement for reassembly . See F ...

  • Lincoln Electric 200 - page 125

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-55 F-55 PIPELINER® 200 FIGURE F .22 – FRONT P ANEL WIRING CONNECTIONS A C B D E IDLER SWIT CH LEADS T O AMMETER DC RECEPT ACLE IDLER PC BOARD T O IDLER SWIT CH IGNITION SWIT CH ST ART BUT T ON SHUNT LEADS QUICK DISC ONNECT 13. Using the slot hea ...

  • Lincoln Electric 200 - page 126

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-56 F-56 PIPELINER® 200 FIGURE F .23 – FRONT P ANEL F ASTENER REMOV AL BOL TS / NUTS / W ASHERS (2) BASE MOUNTING BOL TS (4) MIDDLE SCREW (1) 23. Using the 1/2” wrench, remove the two bolts, nuts, and washers that hold the front panel assembly ...

  • Lincoln Electric 200 - page 127

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-57 F-57 PIPELINER® 200 FIGURE F .24 – BRUSH BRACKET WRAP-AROUND COVER BRUSH BRACKET WRAP- AROUND COVER REMOVE (2) NUTS, W ASHERS, AND SCREWS 27. Using the slot head screw driver , remove the two screws and nuts from the brush bracket wrap-around ...

  • Lincoln Electric 200 - page 128

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-58 F-58 PIPELINER® 200 FIGURE F .26 – MAIN GENERA TOR FEET MOUNTING MAIN GENERA TOR REMOVE MOUNTING NUTS, WASHERS, AND BOL TS FEET (2) 30. Using the 3/4” wrench, remove the frame mounting bolts, nuts, and washers from the feet of the main gene ...

  • Lincoln Electric 200 - page 129

    MAIN GENERA T OR FRAME REMOV AL AND REPLACEMENT PROCEDURE (CONTINUED) TROUBLESHOOTING & REP AIR F-59 F-59 PIPELINER® 200 33. Using the rope sling and pry bars, carefully lift and “wiggle” the generator frame away from the engine and armature assembly . Be careful to support the generator frame as you remove it. NOTE: The exciter frame is a ...

  • Lincoln Electric 200 - page 130

    NOTES F-60 F-60 PIPELINER® 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 131

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric 200 - page 132

    MAIN GENERA TOR ARMA TURE REMOV AL AND REPLACEMENT PROCEDURE TROUBLESHOOTING & REP AIR F-62 F-62 PIPELINER® 200 FIGURE F .28 – MAIN GENERA TOR ARMA TURE MOUNTING MOUNTING BOL TS / LOCK W ASHERS (8) BLOWER P ADDLE SLING PROCEDURE 1. T urn the engine OFF . 2. Perform the DC Exciter Armature Removal procedure. 3. Perform the Main Generator Fram ...

  • Lincoln Electric 200 - page 133

    TROUBLESHOOTING & REP AIR F-63 F-63 PIPELINER® 200 RETEST AFTER REP AIR Retest a machine: • If it is rejected under test for any reason that requires you to remove any mechanical part which could af fect the machineʼs electrical characteristics. OR • If you repair or replace any electrical components. ENGINE OUTPUT Engine Mode No Load RPM ...

  • Lincoln Electric 200 - page 134

    NOTES F-64 F-64 PIPELINER 200 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ...

  • Lincoln Electric 200 - page 135

    T ABLE OF CONTENTS - DIAGRAM SECTION G-1 G-1 PIPELINER 200 E l e c t r i c a l D i a g r a m s ..................................................................... G - 1 W i r i n g D i a g r a m -C o d e 1 0 6 6 0 - ( L 1 1 4 0 2 ) .................................................. G - 2 W i r i n g D i a g r a m -C o d e 1 0 9 1 3 , 1 1 1 3 6 - ...

  • Lincoln Electric 200 - page 136

    ELECTRICAL DIAGRAMS G-2 PIPELINER® 200 WIRING DIAGRAM - CODE 10660 - (L1 1402) A 54 3 2 1 NEGATI VE SELECTOR SWITC H WELDER LEAD BLO CK 42 602A U 1 2 3 4 5 6 600A 41 G ENERA TO R N 600B 6 10 602B J5 P9 J8 POSIT IVE P 10 N U RHEOSTAT (CC -) (CC+ ) & ( CV+ W ITH W.F.M .) Y B W G PLUG F OR REMOT E CONTRO L POTENT IOMET ER B * P8 1 2 3 4 5 6 X 41 ...

  • Lincoln Electric 200 - page 137

    ELECTRICAL DIAGRAMS G-3 PIPELINER® 200 WIRING DIAGRAM - CODE 10913, 1 1 136 - (L1 1864) L11864 PI PEL I NER 2 0 0 G WI RI NG DI AGRAM B A 54 3 2 1 NEGA TI VE SELECTOR SW IT CH WELDE R LEAD BLOCK 42 602A U 1 2 3 4 5 6 600A 41 GEN ERATOR N 600B 610 602B J5 J8 POS ITI VE P10 N U R HEOSTAT (CC -) (CC+ ) & ( CV+ W IT HW .F. M .) Y B W G PLUG F OR R ...

  • Lincoln Electric 200 - page 138

    ELECTRICAL DIAGRAMS G-4 PIPELINER® 200 WIRING DIAGRAM - CODE 10929 - (M20056) 761 F1 15A 840 B PI PELI NER 2 00 D W I RI NG DI AGRAM M2005 6 START + 52 + - - 51 56 EXC + PUMP SO LENOID 50 50B S B + R 1 2 3 4 12 34 5 6 7 8 9 10 J1 J2 61 60A 58A 51A 53B 57 56A 54B 54 59 58 50A FUEL PUMP 53 GLOW PLUGS 6 0C 212A 70 GND-B GND-M 212B GND-N S G I S G I A ...

  • Lincoln Electric 200 - page 139

    ELECTRICAL DIAGRAMS G-5 PIPELINER® 200 WIRING DIAGRAM - CODE 1 1 1 14, 1 1316 - (M20464) S B W IRE FEED MOD ULE (OPT IONAL) 608 609 + PIPEL I NER 200D W I RI NG D IAG R A M A M2 0464 PLUG P5 INL INE CONNECTO RS W .F.M. CONTROL PANEL CONNECT T O POS. & NEG. OUTPUT TERM INALS POS. NEG. #8 LE AD #2 HEA VY LEAD # 2 HEAVY L EAD NEGATIVE CV OUTPUT T ...

  • Lincoln Electric 200 - page 140

    ELECTRICAL DIAGRAMS G-6 PIPELINER® 200 WIRING DIAGRAM - CODE 1 1471 - (M21564) S B W IRE FEED M ODULE ( OP TI ONA L) 608 609 + PIPE LI NER 200D W I RING DIA GRA M B M2 1564 PRINT PL UG P5 INL INE CONNECT ORS W .F.M. CONTROL PANEL CONNECT TO POS. & NEG . OUTPUT T ERMINAL S POS. NEG. #8 LE AD # 2 HEA VY LEAD #2 HEA VY LEAD NEGAT I VE CV OUTPUT T ...

  • Lincoln Electric 200 - page 141

    ELECTRICAL DIAGRAMS G-7 PIPELINER® 200 SCHEMA TIC -COMPLETE MACHINE - CODE 10929 - (L12020) L12020 PIPELI NER 200D MACHINE SCHEMATIC NA L11946 JRS JRS UN LE SS OTHERWI SE SPE CIFIED TO LE RANCE M ANU F AC TURING T OL ER ANC E P ER E 2056 ON 2 PLACE DE CI MALS IS ± .02 O N 3 PLACE D E CIM ALS I S± .002 ON ALL A N GLES IS ± .5 OF A DE G REE WIT H ...

  • Lincoln Electric 200 - page 142

    ELECTRICAL DIAGRAMS G-8 PIPELINER® 200 SCHEMA TIC - COMPLETE MACHINE - CODE 1 1 1 14, 1 1316 - (L12362) L12362 PI PELI NER 2 00 D ( KUBOT A V22 0 3M) MACHINE SCHEMATIC NA L12020 DM J. STAPP UN LE SS OTHERWI SE SPE CIFIED TO LE RANCE M ANU F AC TURING T OL ER ANC E P ER E 2056 ON 2 PLACE DE CI MALS IS ± .02 O N 3 PLACE D E CIM ALS I S± .002 ON AL ...

  • Lincoln Electric 200 - page 143

    ELECTRICAL DIAGRAMS G-9 PIPELINER® 200 SCHEMA TIC - COMPLETE MACHINE - CODE 1 1471 - (L13350) L13350 PIP EL INE R 200 D K UBOTA MA C HI NE SC HE MATI C NONE L12362 DO NOT SCAL E T HIS DR A WING EQU IPM ENT TYPE : SUB JECT : NA CRM 37569 1 PAG E ___ OF ___ 1 EN GIN E ERIN G CON T RO LL ED M ANUF AC T URER: No T HIS DOCUM EN T CON T AIN S PR O PRI E ...

  • Lincoln Electric 200 - page 144

    ELECTRICAL DIAGRAMS G-10 PIPELINER® 200 SCHEMA TIC - CURRENT SENSE PC BOARD - CODE 10929,1 1 1 14, 1 1316, 1 1471 - (S25973) S25973 CLASSI C SERI ES CURRENT SENSE PC BOARD SCH EMAT I C NONE - BTV DM U NLESS OT HER WI SE SPE C IF IED T OLE RA NCE MAN UFA CT URING TOLE RA N CE PER E2056 ON 2 PLACE DEC I MALS IS ± .0 2 ON 3 PLA CE DE CI MA LS IS ±. ...

  • Lincoln Electric 200 - page 145

    ELECTRICAL DIAGRAMS G-11 PIPELINER® 200 SCHEMA TIC - IDLER/ENGINE SHUTDOWN - CODE 10929 (L10826) G-11 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual. Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Retu ...

Fabricant Lincoln Electric Catégorie Welder

Les documents que nous recevons du fabricant de l'appareilLincoln Electric 200 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Lincoln Electric
- manuels d’utilisations 200
- fiches produit Lincoln Electric
- dépliants
- ou étiquettes-énergie Lincoln Electric 200
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Lincoln Electric 200.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Lincoln Electric 200, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Lincoln Electric 200. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Lincoln Electric 200.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Lincoln Electric 200, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Lincoln Electric 200 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Lincoln Electric 200.

Le manuel d’utilisation complet Lincoln Electric, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Lincoln Electric 200 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Lincoln Electric 200, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lLincoln Electric 200 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Lincoln Electric 200 - qui devraient nous aider dans les premières étapes lors de l'utilisation Lincoln Electric 200
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Lincoln Electric 200
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Lincoln Electric 200 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Lincoln Electric 200?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Lincoln Electric 200, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Lincoln Electric 200 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)