Français dropdown-ico

Manuel d’utilisation Audiovox PRO9776C

24 pages 0.49 mb
Télécharger

Aller à la page of 24

Summary
  • Audiovox PRO9776C - page 1

    128-8787 1 of 24 1 SELECT ABLE FEA TURES The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be select ...

  • Audiovox PRO9776C - page 2

    128-8787 2 of 24 2 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch ...

  • Audiovox PRO9776C - page 3

    128-8787 3 of 24 3 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output Pulsed 10 Mins 2nd RF S tart Chirp O f f On On & Car Finder 3rd Run Time 5 Mins 10 Mins 15 ...

  • Audiovox PRO9776C - page 4

    128-8787 4 of 24 4 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time 1 chirp = defrost output ...

  • Audiovox PRO9776C - page 5

    128-8787 5 of 24 5 This Remote S tart/Alarm System is designed to be used with Automatic T ransmission V ehicles Only! The unit provides a selectable ignition control that allows a number of select able timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a ins ...

  • Audiovox PRO9776C - page 6

    128-8787 6 of 24 6 SHOCK SENSOR: Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using tw ...

  • Audiovox PRO9776C - page 7

    128-8787 7 of 24 7 Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of the installing technician to test the remote start unit and assure that the vehicle cannot start via RF control in any gear selection other than park or neutral. In both mechanical and elect ...

  • Audiovox PRO9776C - page 8

    128-8787 8 of 24 8 WIRING THE 4 PIN AL TERNA TE IGNITION HARNESS ORANGE/BLACK Wire: Parking Brake Input This wire is used only when the turbo timer mode, Bank 3, feature # 16 is selected ON. This input insures that the vehicle parking brake is applied whenever the vehicle is set up for and the turbo timer circuit is used. This input must switch to ...

  • Audiovox PRO9776C - page 9

    128-8787 9 of 24 9 WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red T race Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay . If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused +12 volt source. (Max. 15 Amps) Note: ...

  • Audiovox PRO9776C - page 10

    128-8787 10 of 24 10 Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches +12 volts when the door is opened (some Fords and some Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches. In most cases, the Purple wire will need to be connected to only one door swi ...

  • Audiovox PRO9776C - page 11

    128-8787 11 of 24 11 General Motors V A TS By-Pass Diagram Light Blue Wire: Ignition 3 Output This wire provides a 300 mA ground output that becomes active 3 seconds before the Remote S tart Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote S t art Unit turns off. In all of the applications described ...

  • Audiovox PRO9776C - page 12

    128-8787 12 of 24 12 Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This wire should be connected to an external relay , and wired to ...

  • Audiovox PRO9776C - page 13

    128-8787 13 of 24 13 Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay . Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts whe ...

  • Audiovox PRO9776C - page 14

    128-8787 14 of 24 14 Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Green w/ Orange T race Wire: T achometer Input Signal ...

  • Audiovox PRO9776C - page 15

    128-8787 15 of 24 15 Negative Door Switch Wiring Detail Dark Blue Wire: Delayed 300 mA Pulsed Channel 3 Output The Dark Blue wire supplies a 300 mA ground pulsed output whenever channel three of the receiver is accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low current output and must b ...

  • Audiovox PRO9776C - page 16

    128-8787 16 of 24 16 WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote S tart unit's operation. Underst anding these outputs and the time in which they occur will allow you to determine if they are needed for the ...

  • Audiovox PRO9776C - page 17

    128-8787 17 of 24 17 2 Pin T ransponder Control Output: (Y ellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponder bypass relay . The system also allows software selections to control the way in which this output operates, see remote start feature # 10 for setting this output. When the u ...

  • Audiovox PRO9776C - page 18

    128-8787 18 of 24 18 3 Wire Positive Switched Door Lock/Unlock Wiring Detail 3 Wire Ground Switched 2 Step Door Locks In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red wire to the wire that provides a low current ground signal from the factory door lock switch to the factory d ...

  • Audiovox PRO9776C - page 19

    128-8787 19 of 24 19 3 Wire Positive Switched 2 Step Door Locks The green wire provides a positive pulse during arming, or the pulsed +12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay . The red wire provides a positive pulse d ...

  • Audiovox PRO9776C - page 20

    128-8787 20 of 24 20 3a. Within 10 seconds of turning the ignition switch off, Release and then Push On and release the Pushbutton Switch 2 times holding it on the second time until the siren and or lights flash and chirp 2 times indicating that the 2 Hour Start Interval has successfully been set. or 3b. Within 10 seconds of turning the ignition sw ...

  • Audiovox PRO9776C - page 21

    128-8787 21 of 24 21 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the inst allation of an Audiovox Remote S tart Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. H ...

  • Audiovox PRO9776C - page 22

    128-8787 22 of 24 22 vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety ...

  • Audiovox PRO9776C - page 23

    128-8787 23 of 24 23 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignit ...

  • Audiovox PRO9776C - page 24

    128-8787 24 of 24 24 © 2010 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-8787 ...

Fabricant Audiovox Catégorie Automobile Alarm

Les documents que nous recevons du fabricant de l'appareilAudiovox PRO9776C peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Audiovox
- manuels d’utilisations PRO9776C
- fiches produit Audiovox
- dépliants
- ou étiquettes-énergie Audiovox PRO9776C
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Audiovox PRO9776C.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Audiovox PRO9776C, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Audiovox PRO9776C. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Audiovox PRO9776C.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Audiovox PRO9776C, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Audiovox PRO9776C par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Audiovox PRO9776C.

Le manuel d’utilisation complet Audiovox, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Audiovox PRO9776C - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Audiovox PRO9776C, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAudiovox PRO9776C qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Audiovox PRO9776C - qui devraient nous aider dans les premières étapes lors de l'utilisation Audiovox PRO9776C
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Audiovox PRO9776C
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Audiovox PRO9776C dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Audiovox PRO9776C?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Audiovox PRO9776C, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Audiovox PRO9776C il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (1)

antonio garcia garcia

no puedo poner mi grabadora VN-711PC en modo (activación por voz) porque cuando la pongo en modo VCVA el manual dice que para activarlo pise ON y desactivar OF y esta grabadora carece de estos dos botones, cuando pulso el play o el MAS o el MENOS estando en VCVA me sale el mensaje CANCELAR AJUSTES DE GRABACION (que no estaba activarlo porque en las diferente pruebas que ago. no consigo que la voz la active.si me pueden orientar se lo agradecería. Gracias, saludos