-
Oki BISM2 - page 1
www.ezurio.com BISM2 Bluetooth™ V ersion 2.0 Serial Module 1. General Descr iption Ezurio’s BIS M2 Bluetooth Serial Module is a fully integrated and qualified Class 1 Bluetooth solution designed for lowest cost of integration and ownership for designers wishing to incorporate Blueto oth functionality into their products. The module is qualified ...
-
Oki BISM2 - page 2
www.ezurio.com 2. Features Feature Implementation Bluetooth Transmission Class 1 Fully Bluetooth pre-qualified Bluetooth 2.0 Range 250 metres typical (free space) Frequency 2.400 – 2.485 GHz Max Transmit Power +6dBm Min Transmit Power -27dBm Receive Sensitivity Better than -86dB Data Transfer rate Up to 300Kbp s Serial Interface RS-232 bi-direct ...
-
Oki BISM2 - page 3
www.ezurio.com 3. Functional Block Diagram 3.1 Connection Diagram The Module is equipped with a 40-pin 0.5mm pitch board-to -board connector that connects to the applicati on platform. ...
-
Oki BISM2 - page 4
www.ezurio.com 3.2 Pin Descrip tions The Hirose DF12C board-to-bo ard connector on the module is a 40-pin double-row recept acle. The table below defines the pin functions. Note that this pin-out is as viewed from the underside of the Module. Pin No. Signal Description Pin No. Signal Description 1 Analogue 0 1.8v Max 2 GPIO1 I/O for Host. 3 Analogu ...
-
Oki BISM2 - page 5
www.ezurio.com Pin 8 (UART_DCD) is active low. It is n ormally 3.3v. When a conn ection is live this pin is low. This means that when this pin is converted to RS232 voltag e levels it will have the correct volt age level for assertion. Pin 10 (UART_DSR) is an input, with active low logic. It should be connected to the DTR output of the host. When t ...
-
Oki BISM2 - page 6
www.ezurio.com UART_RTS 23 O V OL max=0.2V V OH min=2.8V UART_DSR 10 I V IL max=0.8V V IH min=2.1V V IH max=3.7V UART_DTR 12 O V OL max=0 .2V V OH min=2.8V Shared with GPIO3 UART_RI 6 I or O O/P : V OL max=0.2V V OH min=2.8V I/P : V IL max=0.8V V IH min =2.1V V IH max=3.7V Directio n may be programmed. UART_DCD 8 I or O O/P : V OL max=0 .2V V OH mi ...
-
Oki BISM2 - page 7
www.ezurio.com 3.3.2.4 PCM Interface Signal Name Pin No I/O Signal level Com ments PCM_CLK 20 I or O O/P : V OL max=0.2 V V OH min=2.8V I/P : V IL max=0.8V V IH min =2.1V V IH max=3.7V If un used keep pins open PCM_IN 22 I V IL max=0.8V V IH min=2.1V V IH max=3.7V PCM_SYNC 24 I or O O/P : V OL max=0.2V V OH min=2.8V I/P : V IL max=0.8V V IH min =2. ...
-
Oki BISM2 - page 8
www.ezurio.com 4. I/O Characteristics 4.1 Power Consumption The current drain from the Vc c power input line is dependent on various factors. The three most significant factors are the voltage level at Vcc, UA RT Baudrate and the operating mode. The hardware specification for the Module allows for a voltage range of 3.6 to 7.0 at Vcc. Tests have sh ...
-
Oki BISM2 - page 9
www.ezurio.com 5. DC Characteristics 5.1 RF Performance 5.1.1 Transmit Power Conduc ted Transmit Pow er min: 1.0mW (0dBm) max: 4mW (6dBm) Antenna Gain +2dBi typ. Effective Transmit Power min:0dBm Max: +6dBm Output power can be reduced by program control 5.1.2 Receive Sensitivity Receive Sensitivity -86dBm (at 25°C) Antenna Gain +2dBi typ Effective ...
-
Oki BISM2 - page 10
www.ezurio.com Data Transfer Ra te / Distance 0 100 200 300 400 500 600 700 800 10m 50m 100m 150m 200m 250m 300m Distance (meters) Data Transfer Rate (kbps) RF data rate Serial port data rate 5.3 Temperature Pe rformance Data Transmit Rate with Temperature and Attenuation 0 100 200 300 400 500 600 700 800 -60dBm -65dBm -70dBm -75dBm -80dBm -85dBm - ...
-
Oki BISM2 - page 11
www.ezurio.com Serial Module UART Interface UART_TX UART_RX UART_CTS UART_RTS UART_DSR UART_DTR UART_RI UART_DCD /RXD /TXD /RTS /CTS /DTR /DSR /RING /DCD RS232 Interface 6. Functional Description The BISM 2 Bluetooth module is a self-contai ned Bluetooth product and requires only power to implement full Bluetoo th communication. The integrated, hig ...
-
Oki BISM2 - page 12
www.ezurio.com 6.1.2 SPI bus The Module is a slave device that uses terminals SPI_MOSI , SPI_MI SO, SPI _CLK and SPI_CS B. This interface is used for program firmware updates at the factory. Ezurio supply a PC based utility to all ow firmware upgrade over the UART port. It is h ighly recommended that customers should use this method for updating fi ...
-
Oki BISM2 - page 13
www.ezurio.com 7. Integrated Firmware 7.1 General The BISM 2 has been designed to provide t he fastest route to market for designers who wish to use Bluetooth to wirel essly enable their products. To achieve this Ezurio has implemented a wide ranging set of AT commands that control all of the standard Bluetooth tasks. These remove the complexity of ...
-
Oki BISM2 - page 14
www.ezurio.com ATD00809844EA 13 to the UART of the BISM 2 module. The module will attempt to make a connection and return conn ect 0080984 4ea13,1101 ) or (NO CARRI ER), depending on wh ether the connection was successful. The scope of the AT command set developed by Ezurio is such that most Bluetooth functionality can be covered, greatly reducing ...
-
Oki BISM2 - page 15
www.ezurio.com 7.3.1.5 Bluetooth • Set the module to be a master or slave • Make a Bluetooth connection to a specified device • Perform a full inquiry f or other Bluetoot h devices • Query a remote device to check if a service is offered • Fetch the friendly name of a remote device • Increase or decrease the delay before the master aban ...
-
Oki BISM2 - page 16
www.ezurio.com 8. Low Power Modes The current drain from the Vc c power input line is dependent on various factors. The three most significant factors are the voltage level at Vcc, UA RT baud rate and the operating mode. The hardware specification for the blu2i module allows for a voltage range of 3.6 to 7.0v at Vcc. Tests have shown that there is ...
-
Oki BISM2 - page 17
www.ezurio.com A slave on the other hand does NOT h ave prior knowledge of when a pack et will be recei ved and has to assume that a packet will be received from a master on every receive slot. This means that it has to leave its recei ving circuitry on for most of the receive slot duration. The result of this is high power consumption as illustrat ...
-
Oki BISM2 - page 18
www.ezurio.com 9. Application E xamples 9.1 RS232 Modem Signals Just as a telephony modem has control and status lines, the blu2i Module also provides for 6 control and status lines as per the table below. The direction column is as seen from the module’s viewpoint. Direction Function IN or OUT * CI also known as RI (Ring Indicate) IN or OUT * DC ...
-
Oki BISM2 - page 19
www.ezurio.com 3. PIO3 (DCD) w ill be de-assert ed when the device is in the un connected state. Asserted when a connection is active. See S Registers 552 and 553 for more detai ls. 4. PIO5 is either used as GPI O or driven as UART_DTR . When the u nit is configured in pure host mode, this pin is forced into UART_DTR and is asserted when there is a ...
-
Oki BISM2 - page 20
www.ezurio.com commands. This further mean s that in stand alone mode, the DSR input line MUST be asserted e.g. 0V in TTL signal mode. The slave is configured by: AT&F* ATS512=4 ATS0=-1 AT&W AT+BTR<bdaddr_m> Where <bdaddr_m> is optional. If it is not specified, then the slave unit will accept connections from any device. If spec ...
-
Oki BISM2 - page 21
www.ezurio.com AT&W AT+BTR<bdaddr_m> 9.5 Modem Control and Status Signals A serial port has DTR, DSR, RT S, CTS, DCD and RI c ontrol lines. RTS and CTS are locally controll ed to prevent local buffer overflow. The status of DTR, DRS , DCD and RI can be exchan ged with the remote peer device . If f or example, the DTR/DSR lines are to be e ...
-
Oki BISM2 - page 22
www.ezurio.com 10. Application Information 10.1 Antenna Position The antenna u sed on the BISM2 B luetoot h module is designed to be largel y immune from the effects of proximity detuning. Normally, antennas operating at 2.4GHz are affected by their surroun dings, so that great care is needed in their placeme nt and orientation. The BISM 2 can be u ...
-
Oki BISM2 - page 23
www.ezurio.com 10.2 Power Supp ly Considerations The power supply for the Module has to be a single voltage source of Vcc within the ran ge of 3.6 V to 7.0 V. It must be able to provide sufficient current in a tran smit burst. This can rise to 65mA. The Module includes regulators to provid e local 3.3V. This rail is accessible on connector J2 for m ...
-
Oki BISM2 - page 24
www.ezurio.com 10.5.1 Fixing Pillars Ezurio in conjunction with Rich co has designed a mounting pillar for use with the Bluetooth Serial Module. This allows the module to be securely held to a primary pcb using snap fit details. A variety of different heights are available to accommo date different variants of Hirose stacked connectors. Pillars sup ...
-
Oki BISM2 - page 25
www.ezurio.com 11. Board to Board Connector This chapter provides specificatio ns for the 40-pin board-to-board connecto r which serves as physical interface to the host applicat ion. The receptacle assembled on the Module is Hirose type DF12C. Details are availabl e at: http://www.hirose.co.jp/cataloge_hp/e5 3700036 .pdf 11.1 Stacking Height Matin ...
-
Oki BISM2 - page 26
www.ezurio.com Insulator Material PA , beige natural Stacking height 3.0 mm ; 3.5 mm ; 4.0 mm ; 5.0 mm Insertion force 21 .8N Withdrawal force 1st 10N Withdrawal force 50th 10N Maximum connection cycles 50 12. Qualification 12.1 Bluetooth Qualification Process The following safety precautions must be observed during all phases of the operation, usa ...
-
Oki BISM2 - page 27
www.ezurio.com 12.4 Safety and Regulatory Statements 12.4.1 Europe – EU De claration of Conformity DECLARATION OF CONFORMITY In accordance with Annex I V of the EU direc tive 1999/5/EC Ezurio declare under our r esponsibility that th e BISM2 Module complies with the appropriate essential requirements of the Article 3 of the R&TTE and the othe ...
-
Oki BISM2 - page 28
www.ezurio.com 12.4.2 FCC and Industry Canada Statements This device complies with part 15 of the FCC Rules. Operation is subject to the follo wing two conditions: (1) This device may not cause harmful in terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modi ...
-
Oki BISM2 - page 29
www.ezurio.com 14. Physical Dimensions 14.1 Mechanical Dimensions 14.1.1 Standard Module Location of Connector (Bottom View) All dimensions in mm ...
-
Oki BISM2 - page 30
www.ezurio.com 14.2 BISM2 Module without antenna (spec ial order) The dimensions for this module are identical to the standard BISM 2 illustrated above, but the antenna is replaced with a U-FL connector. TOP VIEW The external antenna used mu st not result in an increased output power. I. e. the total gain of mating connector, cable and antenna must ...
-
Oki BISM2 - page 31
www.ezurio.com Reel – Rienheimer Elektronic ( www.reel-gmbh.de ) manufacture a w ide range of antennae, including their planTEc roof antennae that are ideal for vehicle mounting. Part Number M70CXR 0300 00 XX XX (Contact Reel for availabili ty of a U.FL connection and exact part number) Pacific Wireless ( www.pacwireless.com ) supply a wide range ...
-
Oki BISM2 - page 32
www.ezurio.com SIDE VIEW All dimensions in mm. 14.4 Labelling The label contains the Part number and the un ique Bluetooth address of the module. 14.5 Ordering Information The BISM 2 is available with different variants of engineering or production firmware. Ordering information is provided below: Part Number Description Firmware Version TRBLU23-00 ...
-
Oki BISM2 - page 33
www.ezurio.com 15. Related Documents • blu2i AT Command Set Version 2.11.0 Reference Manua l • blu2i Firmware Release Notes Versio n 2.11.0 • blu2i Multipoint Firmware Reference Manual • BISM Bluetooth Serial Module - Quick S tart Guide • BISM Bluetooth Serial Module - FAQ • Blu2i Application Scenarios • Wireless Develope r’s Kit Us ...
-
Oki BISM2 - page 34
www.ezurio.com b) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Ezurio does not assume responsibilit y for use of an y of the circuitry described, no circuit patent licen ...
Avez-vous une question à propos de Oki BISM2?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Oki BISM2, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Oki BISM2 il est probable qu’il a envie de partager la façon de le résoudre.