Français dropdown-ico

Manuel d’utilisation Teledyne T200U-NOy

42 pages 0.77 mb
Télécharger

Aller à la page of 42

Summary
  • Teledyne T200U-NOy - page 1

    T200U-NOy ANALYZER ADDENDUM (for use with T200 Operators Manual, PN 06858 and with the T200U Addendum, PN 06861) © TELEDYNE ADVANCED POLLUTION INSTRUMENTATION 9480 CARROLL PARK DRIVE SAN DIEGO, CA 92121-5201 USA Toll-free Phone: 800-324-5190 Phone: 858-657-9800 Fax: 858-657-9816 Email: api-sales@teledyne.com Website: http://www.teledyne-api.com/ C ...

  • Teledyne T200U-NOy - page 2

    ...

  • Teledyne T200U-NOy - page 3

    07303C DCN6646 i SAFETY MESSAGES Important safety messages are provided throughout this manual for the purpose of avoiding personal injury or instrument damage. Please read these messages carefully. Each safety message is associated with a saf ety alert symbol, and placed throughout this manual and inside the instrument. The sy mbols with m essages ...

  • Teledyne T200U-NOy - page 4

    ii 07303C DCN6646 CONSIGNES DE SÉCURITÉ Des consignes de sécurité importantes sont fournies tout au long du présent manuel dans le but d’éviter des blessures corporelles ou d’endommager les instruments. Veuillez lire attentivement ces consignes. Chaque cons igne de sécurité est représentée par un pictogramme d’alerte de sécurité; ...

  • Teledyne T200U-NOy - page 5

    07303C DCN6646 iii WARRANTY WARRANTY POLICY (02024F) Teledyne Advanced Pollution Instrumentation (TAP I), a business unit of Teledyne Instruments, Inc., provides that: Prior to shipment, TAPI equipm ent is thoroughly inspected and tested. Should equipment failure occur, TAPI assures its customers that prom pt service and support will be available. ...

  • Teledyne T200U-NOy - page 6

    Model 200EU-NOy Opti on Manual Addendum iv 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 7

    Model 200EU-NOy Opti on Manual Addendum 07303C DCN6646 v TABLE OF CONTENTS 1.0 INTR ODUCTION ...................................................................................................... 7 2.0 SPECIF ICATIONS ................................................................................................... 9 2.1 Specificat ions .......... ...

  • Teledyne T200U-NOy - page 8

    Model 200EU-NOy Opti on Manual Addendum vi 07303C DCN6646 List of Figures Figure 1. Rear Panels: T200U-NOy Analyzer (top) and 501Y (center); Converter (bottom) ...................... 13 Figure 2. Rear Panel Pneumatic Connecti ons ..................................................................................... ....... 14 Figure 3. Replac ing th ...

  • Teledyne T200U-NOy - page 9

    07303C DCN6646 7 1.0 INTRODUCTION The T200U-NOy analyzer consists of an external Converter designed to support a NOx analyzer by converting multiple , unstable compounds grouped under the name NOy . The converter is mounted externally at the sample inlet to m inimize flow time between sample in and converter, thereby optimizing m easurement accurac ...

  • Teledyne T200U-NOy - page 10

    Model T200EU-NOy Opti on Manual Addendum 1.0 Int roduction 8 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 11

    07303C DCN6646 9 2.0 SPECIFICATIONS 2.1 Specifications Table 1 Specifications for the External Converter and the 501Y Bypass Pump Converter Remotely mounted molybdenum external Converter with temperature controller in a NEMA – 4 enclosure. Converter Temperature 315 o C  7 o C with read-out on front panel of bypass pump chassis. Tube/Electrical ...

  • Teledyne T200U-NOy - page 12

    Model T200EU-NOy Option M anual Addendum 2.0 Specifi cations 10 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 13

    07303C DCN6646 11 3.0 GETTING STARTED The NOy converter has been designed to operate with the T200U low level NOx analyzer, with some additional modification.The combination is referred to as the T200U-NOy analyzer. 3.1 Unpacking and Inspection The T200U- NOy comes in three boxes:  The analyzer with AC power cord  501Y Bypass Pump Chassis (ty ...

  • Teledyne T200U-NOy - page 14

    Model T200U-NOy Opti on Manual Addendum 12 07303C DCN6646 3.2 Electrical and Pneumatic Connections NOTE To maintain compliance with EMC standards, it is required that the cable length (at the rear of the analyzer) be no greater than 3 meters for all I/O connections, which include Analog In, Analog Out, Status Out, Control In, Ethernet/LAN, USB, RS- ...

  • Teledyne T200U-NOy - page 15

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 13 Figure 1. Rear Panels: T200U-NOy Analyzer (top) and 501Y (center); Converter (bottom) ...

  • Teledyne T200U-NOy - page 16

    Model T200U-NOy Opti on Manual Addendum 14 07303C DCN6646 Figure 2. Rear Panel Pneumatic Connections Note: Pneumatic tubes and rear panel labels incl ude numbers to facilitate m atching connections between instruments. CONNECTIONS: Analyzer to Pump to Conv erter and Calibrator to Pump Calibrator Analyzer Pump Chassis Converter NO IN (1) NO OUT (1) ...

  • Teledyne T200U-NOy - page 17

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 15 3.3 Initial Operation 1. After confirming proper supply volta ge, turn on the power to the analyzer and the 501Y bypass pump, and plug in the external Pum p. If you are unfamiliar with the T200U-NOy analyzer, we recomm end that you read the overview in Section 3 of its operation manual befor ...

  • Teledyne T200U-NOy - page 18

    Model T200U-NOy Opti on Manual Addendum 16 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 19

    07303C DCN6646 17 4.0 THE T200U-NOY EXTERNAL CONVERTER 4.1 Principle of Operation The T-API Model T200U-NOy is designed to measure the concentration of NO, NO 2 , and other compounds that are too unsta ble to be measured when taken in through the normal ambient air sam ple inlet system. Please refer to the T200U manual supplied with this system for ...

  • Teledyne T200U-NOy - page 20

    Model T200U-NOy Opti on Manual Addendum 18 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 21

    07303C DCN6646 19 5.0 CALIBRATION AND CAL CHECKS Unlike most NOx analyzers, the T200U-NOy does not have a sample inlet port on its rear panel. The sample inlet is located on the external Converter. Follow the steps in the T200U manual to:  Enter the expected NO and NOy span gas concentrations in the analyzer.  Do the zero calibration procedur ...

  • Teledyne T200U-NOy - page 22

    Model T200U-NOy Opti on Manual Addendum 20 07303C DCN6646 5.1 Calibration or Cal Check Procedure Calibration of the analyzer can be check ed or adjusted using gas introduced through the CAL IN (3) port on the 501Y rear panel. The calibration gas is routed to a tee fitting (see CAL IN (6) in Figure 4 ), near the sam ple inlet on the external Convert ...

  • Teledyne T200U-NOy - page 23

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 21 Table 5 Span Calibration Procedure Step Action Comment 1. Press CAL The analyzer enters the calibrate mode. 2. Wait For Stability Type STB < 2 PPB Wait for reading to stabilize at span value. 3. Press SPAN If you change your mind after pressing SPAN, you can still press EXIT here without ...

  • Teledyne T200U-NOy - page 24

    Model T200U-NOy Opti on Manual Addendum 22 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 25

    07303C DCN6646 23 6.0 MAINTENANCE 6.1 Maintenance Schedule The schedule for preventative maintenance is presented in Table 6 below. Qualified Maintenance Personnel Required Table 6 Preventative Maintenance Calendar Item Maintenance Interval Zero/Span Calibration Annually or after maintenance or repairs Zero/Span Checks Daily Particulate Filter Week ...

  • Teledyne T200U-NOy - page 26

    Model T200U-NOy Opti on Manual Addendum 24 07303C DCN6646 6.2 Replacing the Sample Particulate Filters The particulate filter should be inspected often for signs of plugging or contamination. It is also comm on for dirt particles to cause instrument drift, and affect accuracy. To check and change the filter: 1. Fold down the 501Y front panel. 2. Lo ...

  • Teledyne T200U-NOy - page 27

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 25 Figure 3. Replacing the Particulate Filter ...

  • Teledyne T200U-NOy - page 28

    Model T200U-NOy Opti on Manual Addendum 26 07303C DCN6646 6.3 Checking Analyzer Flow Rate The external Pump is capable of maintain ing the reaction cell pressure at less than 5.0 In-Hg-A. If a higher pressure is noted, the Pump may need servicing. Check the Pump and pneumatic system for leaks or rebuild the Pum p. CAUTION! Never operate the analyze ...

  • Teledyne T200U-NOy - page 29

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 27 8. Turn the 501Y power back on. The in sulation can emit a burnt odor for the first 24 hours; this is normal. Allow t he Converter to burn-in for 24 hours, then re-calibrate the instrument. Figure 4. NOy Converter Guts Assembly Location 6.5 Inspecting Pneumatic Lines Particulate matter in th ...

  • Teledyne T200U-NOy - page 30

    Model T200U-NOy Opti on Manual Addendum 28 07303C DCN6646 Figure 5. Pneumatics ...

  • Teledyne T200U-NOy - page 31

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 29 6.6 Checking for Leaks If a leak checker is not available, it is po ssible to leak check the instrument using the sample pump plus a shut-off valve. 1. Turn off power to the analyzer and the 501Y, and unplug the external Pump. 2. Cap the sample inlet of the exter nal Converter, the BYPASS OU ...

  • Teledyne T200U-NOy - page 32

    Model T200U-NOy Opti on Manual Addendum 30 07303C DCN6646 If you have a leak checker: 1. Turn off power to the analyzer and 501Y, and unplug the external Pump. 2. Disconnect the external Pump from the analyzer’s rear panel. Cap the sample inlet of the external Conv erter, the BYPASS OUT port of the 501Y, the ozone generator air inlet (located ins ...

  • Teledyne T200U-NOy - page 33

    07303C DCN6646 31 7.0 TROUBLESHOOTING, ADJUSTMENTS CAUTION! The operations outlined in this section must be performed by qualified maintenance personnel only! This section of the manual contains in formation on diagnosing and repairing instrument performance problem s. It provides troubleshooting procedures that address problems to the board level. ...

  • Teledyne T200U-NOy - page 34

    Model T200U-NOy Opti on Manual Addendum 32 07303C DCN6646 7.1.3 501Y Bypass Pump Diagnostic Procedures The 501Y bypass pump is capable of maintaining a total bypass flow rate of ~2.2 lpm. If flow checks indicate a fall off in bypass flow, the pump may need servicing. Check the pump, inlet fittings, and analy zer for leaks first. If other causes hav ...

  • Teledyne T200U-NOy - page 35

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 33 Indications that would require re-programming are:  Failure / replacement of controller.  Replacement of thermocouple elem ent.  Controller’s loss of PID parameters leading to instability of the tem p setpoint. In the event that the control parameters are changed or in the event t ...

  • Teledyne T200U-NOy - page 36

    Model T200U-NOy Opti on Manual Addendum 34 07303C DCN6646 SECONDARY MENU (The fixed characteristics of the system). PRESS DISPLAY ACTION SEL hold until p-n1 SET TO 0 – REVERSE ACTION SEL hold until p-n2 SET TO 2 = TYPE J THERMOCOUPLE SEL p-dF DIGITAL FILTER SET TO 5 SEL P-SL LOWER LIMIT SET TO -40 (-40ºC) SEL P-SU UPPER LIMIT SET TO 350 (350ºC) ...

  • Teledyne T200U-NOy - page 37

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 35 Figure 7 Electrical Diagram ...

  • Teledyne T200U-NOy - page 38

    Model T200U-NOy Opti on Manual Addendum 36 07303C DCN6646 This page intentionally left blank. ...

  • Teledyne T200U-NOy - page 39

    07303C DCN6646 37 8.0 T200U-NOY SPARE PARTS LIST The following spare parts list supplements the spare parts list for the T200U analyzer. Note Use of replacement parts other than those s upplied by API m ay result in non-compliance with European Standard EN 61010-1. Note Due to the dynamic nature of part numbers , please refer to the TAPI W ebsite a ...

  • Teledyne T200U-NOy - page 40

    Model T200U-NOy Opti on Manual Addendum 38 07303C DCN6646 Reference: 06848 11/8/2010 1:13:10 PM PARTNUMBER DESCRIPTION 041800600 PCA, PMT PREAMP, VR, 041920000 ASSY, THERMISTOR 042680100 ASSY, VALVE (SS) 043420000 ASSY, HEATER/THERM, O2 SEN 044340000 ASSY, HTR, BYPASS MANIFOLD 044540000 ASSY, THERMISTOR, NOX 044600000 AKIT, SPARES, NOX 045230100 PC ...

  • Teledyne T200U-NOy - page 41

    Model T200U-NOy Opti on Manual Addendum 07303C DCN6646 39 Reference: 06848 11/8/2010 1:13:10 PM PARTNUMBER DESCRIPTION CN0000073 POWER ENTRY, 120/60 (KB) FL0000001 FILTER, SS (KB) FL0000003 FILTER, DFU (KB) FM0000004 FLOWMETER (KB) FT0000010 CONNECTOR-ORING, SS, 1/8" (HK) HW0000005 FOOT HW0000020 SPRING HW0000030 ISOLATOR HW0000036 TFE TAPE, 1 ...

  • Teledyne T200U-NOy - page 42

    Model T200U-NOy Opti on Manual Addendum 40 07303C DCN6646 This page intentionally left blank. ...

Fabricant Teledyne Catégorie TV Converter Box

Les documents que nous recevons du fabricant de l'appareilTeledyne T200U-NOy peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Teledyne
- manuels d’utilisations T200U-NOy
- fiches produit Teledyne
- dépliants
- ou étiquettes-énergie Teledyne T200U-NOy
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Teledyne T200U-NOy.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Teledyne T200U-NOy, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Teledyne T200U-NOy. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Teledyne T200U-NOy.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Teledyne T200U-NOy, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Teledyne T200U-NOy par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Teledyne T200U-NOy.

Le manuel d’utilisation complet Teledyne, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Teledyne T200U-NOy - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Teledyne T200U-NOy, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTeledyne T200U-NOy qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Teledyne T200U-NOy - qui devraient nous aider dans les premières étapes lors de l'utilisation Teledyne T200U-NOy
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Teledyne T200U-NOy
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Teledyne T200U-NOy dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Teledyne T200U-NOy?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Teledyne T200U-NOy, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Teledyne T200U-NOy il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)