Français dropdown-ico

Manuel d’utilisation Kenwood DX-7

28 pages 0.77 mb
Télécharger

Aller à la page of 28

Summary
  • Kenwood DX-7 - page 1

    m DIGITAL AUDIO TAPE RECORDER DX-7 INSTRUCTION MANUAL KENWOOD CORPORATION For your records Record the serial number, found bottom of the unit in the spaces desig- nated on the warranty card, and in the space provided below. Refer to the model and serial ~umbers whenever you call your dealer for infor- mation or service on this product. Model DX-7 S ...

  • Kenwood DX-7 - page 2

    Unpacking Unpack the unit carefully and make sure that all accessories and cables are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping compa- ny without delay. Only th ...

  • Kenwood DX-7 - page 3

    Precautions for use To maintain the high performance and reliability of this unit, avoid using or storing it in the following conditions. • Dusty places. • Near heat sources such as stoves, etc. • Condensation (dew) • Places exposed to direct sun- light, especially in a closed car . • Extremely cold places. • In moist, humid locations o ...

  • Kenwood DX-7 - page 4

    Use of OAT cassette tapes • Tapes cannot be turned over and played on the other side. • Tapes are manufactured with a sealed construction. Do not try to forcefully open the tape cover or pull the tape from the case, and never attempt to disassemble the tape case. • Do not repeatedly insert and remove a tape without playing or recording the ta ...

  • Kenwood DX-7 - page 5

    • OAT tape recording system Tape running direction PCM audio signals Subcode area DX-7 5 ...

  • Kenwood DX-7 - page 6

    Controls, connectors and indicators ® ® ®@® @® @ @ @ , - f- PLAY/RE EAT ST lEJECT 'VEl"S -10 Rm I (r>/<+ Im~) - -, , , 0' , L , I' :tR, 'I ,-,.,-, ,-:1!- R Ilifm Ide] -50-24 -12 3 OVER REW FF Uo,~jLJ Ilm:J PAUSE UoAE lEW II- UE ) @@ ®@ @@ 6 DX-7 ...

  • Kenwood DX-7 - page 7

    CD Cassette holder @ [ II ] Pause indicator @ POWER switch @ [REC] Recording indicator ® KEY HOLD/TIMER switch @ [ST -10] indicator *0 VOLUME control knob @ Tune number display ® DC IN jack @ PHONES/REMOTE jack ® Threaded hole for accessory @ DIGITAL I/O jack attachment *@ REC (Record) button (j) System connection jack *@ PAUSE button ® Accesso ...

  • Kenwood DX-7 - page 8

    Power source • How to use the unit with the supplied AC adaptor • Insert the plug of the AC adaptor into the [DC IN] jack on the main unit's rear panel, then con- nect the power plug to a household AC power outlet. • Always set the [POWER] switch to OFF before connecting the AC adaptor. When disconnecting the AC adaptor as well, be sure ...

  • Kenwood DX-7 - page 9

    • Using rechargeable batteries Use the separately sold AID converter (BP-A7). • Align the AID converter with the main unit's accessory attachment guide hole and attach. Secure the AID converter in place using the accessory attachment screw. • Always turn the [POWER] switch OFF before inserting/removing batteries or making connections. ? ...

  • Kenwood DX-7 - page 10

    Connections • Headphone connection • Connect separately sold headphones (use headphones equipped with a 3.5 mm diameter stereo miniplug) to the main unit's [ n IREMOTE] jack or the remote controller's [PHONES] jack. • Always turn the volume down before plugging or unplugging the headphones. • Sound volume adjustment Adjustment usi ...

  • Kenwood DX-7 - page 11

    • Connection to a component equipped with digital 1/0 jacks (coaxial) • Turn off the power to both the amplifier and this unit before making connections. • Using the supplied digital connection cord, connect the 4-pin miniplug to this unit's [DIGITAL 1/0] terminal. Connect the red plug to the component's (amplifier, etc.) coaxial in ...

  • Kenwood DX-7 - page 12

    • Connection to an amplifier's analog input jacks • Turn off the power to both the amplifier and this unit before making connections. • Using the supplied analog connection cord, connect the 3-pin miniplug to this unit's [ n I REMOTE] terminal. Connect the other end of the cord to the amplifier's external input jacks (AUX jacks ...

  • Kenwood DX-7 - page 13

    • Connection for analog recording Use the separately sold AID converter (BP-A7). • Turn off the power to both the amplifier and this unit before making connections. • Connect the AID converter unit (supplied in the BP-A71 to this unit. • Connect the AID converter unit's [MIC/LINE IN] jack to an amplifier's [TAPE REC] jacks or a st ...

  • Kenwood DX-7 - page 14

    Key Hold function 14 DX-7 Setting this function prevents incorrect oper- ation of the unit even if an operation button is accidentally pressed. • When you set the main unit's [KEY HOLD/TIMER] switch to "HOLD", the unit ignores any button operation. • When you set the remote controller's [HOLD] switch to the "." pos ...

  • Kenwood DX-7 - page 15

    To playback a OAT cassette (Basic operation) First load a tape into the unit (see page 141. Operation is possible with ei!her the main unit or the remote controller. ~ 11.-' r u-CoJ Tune number Totaf elapsed display time display n, U~, • To playa tape • Press the [PLAY/REPEAT] button. • Tapes recorded in extended play mode cannot be play ...

  • Kenwood DX-7 - page 16

    " -, u~, I Display example When the tape is stopped at the beginning When the tape is stopped at the end r end • When the beginning of the displayed tune is reached, " ~ " appears on the display and playback begins. • If the [PAUSE] button is pressed during the skip operation, the unit enters pause mode at the beginning of the de ...

  • Kenwood DX-7 - page 17

    " -, u.:J • Cue/Review function This function allows you to fast-forward (cue) or rewind (review) while listening to the tape sound. • To cue, press the [PAUSE] button and then press the [FF/CUE] button. • To review, press the [PAUSE] button and then press the [REW/REVIEW] button. • When you reach the location you want to listen to, pr ...

  • Kenwood DX-7 - page 18

    Digital recording First load a tape into the unit (see page 14). Operation is possible with either the main unit or the remote controller. "" LILI ~II .- 11.1111 U'LILI rl I ST·ID mill • LI I 11.11 -, ULI :J 18 DX-7 Connect the unit (See page 11.) • Press the [REC] button. When starting recording from the begin- ning of the tape ...

  • Kenwood DX-7 - page 19

    Analog recording Use the separately sold AID converter (BP-A7), First load a tape into the unit (see page 14), Operation is possible with either the main unit or the remote controller, 1[1[/:: ~II I~ ~~I~dB~I~-~5~O~24~'~2~3~O"'V"'ER~ MIC (ATT] OdB 20dB LINE l'fino) +-+ " 'ST.ID [jjg] .. '_" nn =, U& ...

  • Kenwood DX-7 - page 20

    Stopping/pausing recording • Operation is possible with either the main unit or the remote controller. • Erasing a recording • To pause recording • Press the [PAUSE] button. If five minutes elapse in pause mode, the rotating head moves away from the tape to protect the tape. (The REC indicator blinks.1 • To stop without recording an END-I ...

  • Kenwood DX-7 - page 21

    Timer recording/Timer playback • Before connecting the timer, insert a tape into the unit. • When carrying out timer recording, make sure the accidental erasure protection "slide door" of cassette tape (page 41 is closed to the right side . • Timer recording o Set the [KEY HOLDITIMER] switch to "REC", then fJ set the [POWE ...

  • Kenwood DX-7 - page 22

    seMS SCMS (Serial Copy Management System) SCMS is a new standard which allows you to make only first generation copies of digital sources (CD, etc.) which contain a copy prohibition code. Copy prohibition code Sources which contain a copy prohibition code include the following: COs and some commercially available OAT music tapes. When carrying out ...

  • Kenwood DX-7 - page 23

    Subcodes With OAT tapes. in addition to the recorded music signal. various subcodes are recorded on the tape to aid in music selection and editing. With commercially available OAT music tapes. subcodes are prerecorded on the tapes. With blank tapes that you record yourself. subcodes are automatically recorded during recording and can also be record ...

  • Kenwood DX-7 - page 24

    Subcode editing • To manually write a ST-ID during recording • In situations such as when recording an audio source that has no space between tunes, you can manually write ST -IDs in the appropriate locations while recording is being carried out. • After writing a ST-ID, you must wait at least 9 seconds before writing the next ST-ID. • You ...

  • Kenwood DX-7 - page 25

    • To erase an unnecessary ST-ID from a recorded tape • If the tune number changes at a place other than between two tunes. an unnecessary ST -10 is written on the tape. Erase the ST-ID using the following procedure. Display example • The unit enters pause mode after the unneces- • The tape automatically rewinds to the begin- ning of the unn ...

  • Kenwood DX-7 - page 26

    • To write an END-ID on a recorded tape • If a tape was stopped at the end of a recording without writing an END-ID, you can use the following procedure to write the necessary END-ID. Play the tape and press the ISTOPI button at the end of the recording. Verify that the'total elapsed time is still shown on the display. I Display example &q ...

  • Kenwood DX-7 - page 27

    Cleaning • Cleaning the cabinet Clean the cabinet by wiping with a dry cloth. If an area is particularly dirty and cannot be cleaned well with a dry cloth, wipe the area with a cloth dampened with water, then wipe dry with a dry cloth. (Do not use benzene, thinner, or other chemicals.1 Always keep terminals and plugs clean. • Cleaning the head ...

  • Kenwood DX-7 - page 28

    Specifications Tape recording system .................. DAT rotating head system Tape speed.......... .. ................. 8.15 mm/sec Sampling frequency ...................... 48 kHz/44.1 kHz/32 kHz No. of quantization bits ...... .......... 16 bits, linear Frequency response ........ ............. 5-22,000 Hz (EIAJI (for digital recording I Signa ...

Fabricant Kenwood Catégorie Microcassette Recorder

Les documents que nous recevons du fabricant de l'appareilKenwood DX-7 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Kenwood
- manuels d’utilisations DX-7
- fiches produit Kenwood
- dépliants
- ou étiquettes-énergie Kenwood DX-7
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Kenwood DX-7.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Kenwood DX-7, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Kenwood DX-7. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Kenwood DX-7.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Kenwood DX-7, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Kenwood DX-7 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Kenwood DX-7.

Le manuel d’utilisation complet Kenwood, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Kenwood DX-7 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Kenwood DX-7, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKenwood DX-7 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Kenwood DX-7 - qui devraient nous aider dans les premières étapes lors de l'utilisation Kenwood DX-7
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Kenwood DX-7
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Kenwood DX-7 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Kenwood DX-7?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Kenwood DX-7, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Kenwood DX-7 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)