Français dropdown-ico

Manuel d’utilisation Sony RS-232C

62 pages 1.42 mb
Télécharger

Aller à la page of 62

Summary
  • Sony RS-232C - page 1

    Digital P o wered Mix er SRP-X700P RS-232C Interface Man ual 2nd Edition Issued: Oct. 2003  2003 Sony Corporation ...

  • Sony RS-232C - page 2

    – 2 – T able of Contents Overview ................................................................................................................................... 4 Connecting Computer ............................................................................................................. 4 Communication Format ......................... ...

  • Sony RS-232C - page 3

    – 3 – LINE OUTPUT1,2 PARAMETER REQUEST Command ....................................... 39 LINE OUTPUT3-8 Command ................................................................................... 39 LINE OUTPUT3-8 PARAMETER REQUEST Command ....................................... 41 MIC INPUT Command ............................................ ...

  • Sony RS-232C - page 4

    – 4 – Overview This is the Interface Manual for the Sony SRP-X700P Digital Po wered Mixer . This protocol is designed to control the SRP-X700P D igital Powered Mix er from an externally connected computer . Read this manual together with Operating Instructions. Caution The material contained in this manual consists of information that is the pr ...

  • Sony RS-232C - page 5

    – 5 – Communication Pr otocol The communication protocol is described below . • When the SRP-X700P has recei ved a command from computer successfully , the SRP-X700P returns “ AC K ” (Ackno wledge). When the SRP-X700P fails to process the command due to reception error or others, it returns “ NAK ” (Not Acknowledge). • When a comput ...

  • Sony RS-232C - page 6

    – 6 – Command Refer ence Basic Contr ol Commands The group of the Basic Control Commands contains 12 commands that enable you to perform the basic operations such as changing the sound volume, switching the LINE4 SELECT OR of the SRP-X700P and others. CONTR OL S: 43[H] 52[H] 43[H] 53[H] ( ‘ CRCS ’ ) This command is used to control an extern ...

  • Sony RS-232C - page 7

    – 7 – RE MO TE CO MMAN D St op send ing 30 [H] ( ‘ 0 ’ ) PLA Y 31[H] ( ‘ 1 ’ ) PA US E 32 [H] ( ‘ 2 ’ ) ST OP 33[H] ( ‘ 3 ’ ) F. F. 34 [H ] ( ‘ 4 ’ ) REW. 35[H] ( ‘ 5 ’ ) RE C 36 [H] ( ‘ 6 ’ ) NEXT 3 7 [H] ( ‘ 7 ’ ) PR EV. 38 [H ] ( ‘ 8 ’ ) PO WER ON 39[H] ( ‘ 9 ’ ) PO WER ST AN DBY 3A [H ] ( ‘ : ’ ) ...

  • Sony RS-232C - page 8

    – 8 – • F ader level (2nd byte) Set the fader le vel [dB]. Example: When changing the sound volume of the MASTER A to 0 dB 43[H] 4C[H] 56[H] 4C[H] 40[H] 59[H] 0D[H] ( ‘ C L V L @ Y CR ’ ) LEVEL DO WN: 43[H] 4C[H] 56[H] 2D[H] ( ‘ CLV – ’ ) This command is used to decrease the sound volume of the specif ied channel. When this comma is ...

  • Sony RS-232C - page 9

    – 9 – LEVEL UP: 43[H] 4C[H] 56[H] 2B[H] ( ‘ CL V+ ’ ) This command is used to increase the sound volume of the specif ied channel. When this command is sent, the sound volume k eeps increasing. When the LEVEL UP/DO WN ST OP command that is described later , is sent, the sound volume stops increasing. V ariable range of a sound volume is fro ...

  • Sony RS-232C - page 10

    – 10 – MUTING: 43[H] 4D[H] 55[H] 54[H] ( ‘ CMUT ’ ) This command is used to mute the specified channel or cancel muting of the specif ied channel. • Packet f ormat 43[H] 4D[H] 55[H] 54[H] “ parameter ” 0D[H] • Parameter The parameter consists of the two-byte data in the follo wing order . • Channel Same as that of LEVEL DO WN comm ...

  • Sony RS-232C - page 11

    – 11 – P ARALLEL OUTPUT ON: 43[H] 50[H] 4F[H] 4E[H] ( ‘ CPON ’ ) This command is used to turn on OUTPUT of the REMO TE P ARALLEL terminals separately of the SRP-X700P . • Packet f ormat 43[H] 50[H] 4F[H] 4E[H] “ parameter ” 0D[H] • Parameter Same as that of the P ARALLEL OUT OFF command. Example: When turning on channel 1 43[H] 50[H ...

  • Sony RS-232C - page 12

    – 12 – SCENE RECALL: 43[H] 52[H] 43[H] 4C[H] ( ‘ CRCL ’ ) This command is used to recall the desired scene. • Packet f ormat 43[H] 52[H] 43[H] 4C[H] “ parameter ” 0D[H] • Parameter Specify the scene number that you want to use, as the parameter . • Scene No. Specify the scene number that you want to use. Example: When recalling sc ...

  • Sony RS-232C - page 13

    – 13 – • Parameter The parameters to be returned ha ve the follo wing meaning. by t e Pa ra me te r na me Spec ifi ed Val ue by t e Pa ra me te r na me 1st MIC 1/ W L 1 LEVEL ME TER V ALUE 38t h PA RALLEL IN PUT7- 1 2 2nd MIC 2/ W L 2 LEVEL ME TER V ALUE 39t h PA RALLEL OU TPU T1-6 3rd MIC 3 LE VEL ME TER V ALUE 40t h PA RALLEL OU TPU T7-1 0 ...

  • Sony RS-232C - page 14

    – 14 – Level meter value The lev el meter values [dB] ar e indicated as shown belo w . MIC SWITCH This command is used to display the status of the +48V switches of the MIC1/WL1 to MIC6/LINE2 by the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 01 MIC6/LINE2 MIC5/LINE1 MIC4 MIC3 MIC2/WL2 MIC1/WL1 When the corresponding bit is ‘ 1 ’ , ...

  • Sony RS-232C - page 15

    – 15 – MIC INPUT – ∞ T urning on/of f of the - ∞ indicators of MIC1/WL1 to MIC6/LINE2 is indicated by the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 MIC6/ MIC5/ MIC4 MIC3 MIC2/ MIC1/ LINE2 LINE1 WL2 WL1 When the corresponding bit is ‘ 1 ’ , – ∞ indicator turns on. When the corresponding bit is ‘ 0 ’ , – ∞ indi ...

  • Sony RS-232C - page 16

    – 16 – CLIP/PROTECTION T urning on/of f of the CLIP and PR O TECTION indicators of speaker output is indicated by the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 0 0 0 PR O TECTION CH2 CLIP CH1 CLIP When the corresponding bit is ‘ 1 ’ , the indicator turns on. When the corresponding bit is ‘ 0 ’ , the indicator turns off. Bi ...

  • Sony RS-232C - page 17

    – 17 – PARALLEL OUTPUT7-10 Presence or absence of output signal at the P ARALLEL OUTPUT7 to 10 connectors on the rear panel of the SRP-X700P is indicated b y the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 0 0 OUT10 OUT9 OUT8 OUT7 When the corresponding bit is ‘ 1 ’ , output signal is present. When the corresponding bit is ‘ 0 ...

  • Sony RS-232C - page 18

    – 18 – MIC MUTING Status of muting of MIC1/WL1 to MIC6/LINE2 is indicated by the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 MIC6/ MIC5/ MIC4 MIC3 MIC2/ MIC1/ LINE2 LINE1 WL2 WL1 When the corresponding bit is ‘ 1 ’ , the audio is muted. When the corresponding bit is ‘ 0 ’ , muting is released. Bit-6 and bit-7 are fix ed all ...

  • Sony RS-232C - page 19

    – 19 – GROUP MUTING Status of muting of REMO TE1 to 6 among the GR OUP F ADER is indicated by the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 REMO TE6 REMO TE5 REMO TE4 REMO TE3 REMO TE2 REMO TE1 When the corresponding bit is ‘ 1 ’ , it is is muted. When the corresponding bit is ‘ 0 ’ , muting is released. Bit-6 and bit-7 ar ...

  • Sony RS-232C - page 20

    – 20 – LOCK/FADER Status of the P ANEL LOCK and that of F ADER MODE are indicated by the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 0 0 0 0 P ANEL LOCK F ADER When bit 0 is ‘ 1 ’ , it indicates that the fader is in the A CTIVE mode. When bit 0 is ‘ 0 ’ , it indicates that the f ader is in the IN A CTIVE mode. When bit 1 is ...

  • Sony RS-232C - page 21

    – 21 – byt e ON OFF 1st 3B[ H] ( ‘ ; ’ ) 3B[ H] ( ‘ ; ’ ) 2n d 33 [H] ( ‘ 3 ’ )3 3 [ H ] ( ‘ 3 ’ ) 3r d 31 [H] ( ‘ 1 ’ )3 1 [ H ] ( ‘ 1 ’ ) 4th 43[ H] ( ‘ C ’ )4 0 [ H ] ( ‘ @ ’ ) 5t h 7F [H] ( ‘ DEL ETE ’ )4 0 [ H ] ( ‘ @ ’ ) Parameter Setting Commands The follo wing commands are the group of commands us ...

  • Sony RS-232C - page 22

    – 22 – A UT O MIX EDIT P ARAMETER: 43[H] 41[H] 4D[H] 50[H] ('CAMP') This command is used to set up the parameter of the automatic mixer . Caution This command is supported by the SRP-X700P firmw are versions of 1.20 and higher . • Packet f ormat 43[H] 41[H] 4D[H] 50[H] "parameter (14 b ytes)" 0D[H] • Parameter The parame ...

  • Sony RS-232C - page 23

    – 23 – • INPUT COMPRESSOR THRESHOLD (1st byte) This command is used to set the threshold lev el of the compressor of the input channel. • INPUT COMPRESSOR RA TIO (2nd byte) This command is used to set the ratio of the compressor of the input channel. LEVEL [dB] LEVEL [dB] LEVEL [ dB] -60 20[H] (' ') -33 3B[H] (';') -6 56 ...

  • Sony RS-232C - page 24

    – 24 – Cauti o • INPUT COMPRESSOR A TT A CK TIME (3rd byte) This command is used to set the attack time of the compressor of the input channel. • INPUT COMPRESSOR RELEASE TIME (4th byte) This command is used to set the release time of the compressor of the input channel. • INPUT GA TE THRESHOLD (5th byte) This command is used to set the t ...

  • Sony RS-232C - page 25

    – 25 – • INPUT GA TE HOLD TIME (6th byte) This command is used to set the hold time of the gate of the input channel. The setup procedure is the same as the input compressor release time (the fourth byte). • INPUT GA TE RELEASE TIME (7th byte) This command is used to set the release time of the gate of the input channel. The setup procedure ...

  • Sony RS-232C - page 26

    – 26 – • LINE OUTPUT 1-6 ON/OFF (13th byte) This command is used to turn ON/OFF the automatic mixer according to the output channels. When you want to turn it ON, set the corresponding bit to 1. When you want to turn it OFF , set the corresponding bit to 0. Bit- 6 and bit-7 are fix ed all the time. MSB LSB bit7 bit6 bit5 bit4 bit3 bit2 bit1 b ...

  • Sony RS-232C - page 27

    – 27 – F A CT OR Y PRESET : 43[H] 52[H] 53[H] 54[H] ( ‘ CRST ’ ) This command is used to return the parameters of the SRP-X700P to the default v alues when shipped from the factory . • Packet f ormat 43[H] 52[H] 53[H] 54[H] 0D[H] When communication with the SRP-X700P is established with success, all parameters including scene memories ret ...

  • Sony RS-232C - page 28

    – 28 – by t e Pa ram e te r na m e 1s t-7 t h FIRM W ARE VE RSI ON 8t h 30[ H] ( ‘ 0 ’ ) fixed CH ANN EL MI C1 /W L1 31 [ H] ( ‘ 1 ’ ) MI C2 /W L2 32 [ H] ( ‘ 2 ’ ) MIC3 33[H] ( ‘ 3 ’ ) MIC4 34[H] ( ‘ 4 ’ ) MIC5/LINE1 35[H] ( ‘ 5 ’ ) MIC6/LINE2 36[H] ( ‘ 6 ’ ) CANCE L 37[H] ( ‘ 7 ’ ) FIRMW ARE VERSION REQUEST : 5 ...

  • Sony RS-232C - page 29

    – 29 – GROUP F ADER : 43[H] 47[H] 46[H] 41[H],42[H] ( ‘ CGF A,B ’ ) 43[H] 47[H] 46[H] 31[H]-36[H] ( ‘ CGF1-2 ’ ) This command is used to set any desired single channel of the GR OUP F ADER. V arious setups can be memorized in the scene memories by specifying these scene Nos. The commands that correspond to the respectiv e channels are s ...

  • Sony RS-232C - page 30

    – 30 – • Index (2-9th byte) This command is used to specify index of the input channels with 8 bytes of the ASCII code. Caution If number of index characters does not reach the 8 bytes, be sure to f ill the blanks with the space (20[H]). • MIC INPUT fader (10th byte) This command is used to set the MIC1/WL1 to MIC6/LINE2 channels ’ assign ...

  • Sony RS-232C - page 31

    – 31 – GROUP F ADER P ARAMETER REQUEST: 52[H] 47[H] 46[H] 41[H],42[H] ( ‘ RGF A,B ’ ) 52[H] 47[H] 46[H] 31[H]-36[H] ( ‘ RGF1-2 ’ ) This command is used to read the setup of any desired single channel of the GR OUP F ADER from the SRP-X700P . The commands that correspond to the respectiv e channels are sho wn below . • Packet f ormat 5 ...

  • Sony RS-232C - page 32

    – 32 – • INFORMA TION (2-129th byte) Specify the information of the input channels using the ASCII code. Caution If number of information characters does not reach the 128 bytes, be sure to fill the blanks with the space (20[H]) so that it becomes 128 bytes all the time. INFORMA TION P ARAMETER REQUEST : 52[H] 49[H] 4E[H] 46[H] ( ‘ RINF ’ ...

  • Sony RS-232C - page 33

    – 33 – • TRIM (10th byte) This command is used to set the reference le vel of the input terminal. • Function ON/OFF (11th byte) This command is used to turn ON/OFF the parametric equalizer with the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 01000P E Q 00 When you want to turn ON the function, set bit 2 to 1. When you want to turn O ...

  • Sony RS-232C - page 34

    – 34 – • PEQ Q (13 and 16th byte) This command is used to set the Q value of parametric equalizer . • PEQ gain (14 and 17th byte) This command is used to set the gain [dB] at the center frequenc y of parametric equalizer . • Gain Limit le vel (18th byte) This command is used to set the le vel [dB] at the Gain Limit. QQ QQ 0.1 5 30 [H] ( ? ...

  • Sony RS-232C - page 35

    – 35 – • Fader le vel (19th byte) This command is used to set the fader le vel [dB]. This fader le vels are sho wn as the fader v alues on the INPUT O VER VIEW screen of the supplied software SRP-X700P Manager . Example: When setting the respectiv e parameters as sho wn below . Scene No. : NONE Index : CD TRIM : -10dBu Function OFF : PEQ ON P ...

  • Sony RS-232C - page 36

    – 36 – LINE 4 INPUT : 43[H] 49[H] 4D[H] 34[H] ( ‘ CIL4 ’ ) This command is used to implement setting up the LINE 4 input channel. V arious setups can be memorized in the scene memories by specifying these scene Nos. • Packet f ormat 43[H] 49[H] 4D[H] 34[H] “ parameter ” 0D[H] • Parameter The parameter consists of the 64 bytes all th ...

  • Sony RS-232C - page 37

    – 37 – LINE OUTPUT1,2 : 43[H] 4F[H] 4C[H] 31[H],32[H] ( ‘ COL1,2 ’ ) This command is used to implement setup of any desired single channel of the LINE OUTPUT1 and 2. V arious setups can be memorized in the scene memories by specifying these scene Nos. The commands that correspond to the respectiv e channels are sho wn below . • Packet f o ...

  • Sony RS-232C - page 38

    – 38 – • REF LEVEL (10th byte) This command is used to set the reference output le vel [dBu]. • Function ON/OFF (11th byte) This command is used to turn ON/OFF the delay (DELA Y), parametric equalizer (PEQ) and high-cut filter (HCF) with the 8-bit data . bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 0 0 0 HCF PEQ DELA Y Set the corresponding ...

  • Sony RS-232C - page 39

    – 39 – LINE OUTPUT 1,2 P ARAMETER REQUEST : 52[H] 4F[H] 4D[H] 31[H],32[H] ( ‘ R OL1,2 ’ ) This command is used to read the setup of any desired single channel of the LINE OUTPUT 1 and 2 from the SRP-X700P . The commands that correspond to the respectiv e channels are sho wn below . • Packet f ormat 52[H] 4F[H] 4C[H] 31[H] “ parameter ? ...

  • Sony RS-232C - page 40

    – 40 – • Parameter The parameter consists of the 26 bytes all the time in the order as shown in the ta ble below . When you specify NONE (30[H] ‘ 0 ’ ) as the scene No. in the 1st byte, you can establish the present setup. At the same time, when you specify the scene No.(31[H] ( ‘ 1 ’ ) through 44[H] ( ‘ D ’ )), parameters of the ...

  • Sony RS-232C - page 41

    – 41 – LINE OUTPUT3-8 P ARAMETER REQUEST : 52[H] 4F[H] 4D[H] 33[H]-38[H] ( ‘ R OL3-8 ’ ) This command is used to read the setup of any desired single channel of the LINE OUTPUT 3 to 8 from the SRP-X700P . The commands that correspond to the respectiv e channels are sho wn below . • Packet f ormat 52[H] 4F[H] 4C[H] 33[H] “ parameter ” ...

  • Sony RS-232C - page 42

    – 42 – • Packet f ormat 43[H] 49[H] 4D[H] 31[H] “ parameter ” 0D[H] (In the case of MIC1/WL1 input channels) • Parameter The parameter consists of the 41 bytes all the time in the order as shown in the ta ble below . When you specify NONE (30[H] ‘ 0 ’ ) as the scene No. in the 1st byte, you can establish the present setup. At the sa ...

  • Sony RS-232C - page 43

    – 43 – • TRIM (10th byte) This command is used to set the reference le vel [dBu] of the input terminals. • Function ON/OFF (11th byte) This command is used to turn ON/OFF the parametric equalizer (PEQ), feedback reducer (FR) and lo w-cut filter (LCF) with the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 01000P E Q F R L C F When you ...

  • Sony RS-232C - page 44

    – 44 – MIC INPUT P ARAMETER REQUEST : 52[H] 49[H] 4D[H] 31[H]-36[H] ( ‘ RIM1-6 ’ ) This command is used to read the setup of any desired single channel of the MIC input channels from the SRP-X700P . The commands that correspond to the respecti ve channels are shown belo w . • Packet f ormat 52[H] 49[H] 4D[H] 31[H] “ parameter ” 0D[H] ...

  • Sony RS-232C - page 45

    – 45 – When you specify the scene No.(31[H] ( ‘ 1 ’ ) through 44[H] ( ‘ D ’ )), parameters of the subsequent 2nd through 8th bytes are written in the scene memory . • Scene No. (1st byte) This command is used to specify the scene No. • MIC MUTING (2nd byte) This command is used to specify muting of the MIC input channels with the 8- ...

  • Sony RS-232C - page 46

    – 46 – • MASTER MUTING (6th byte) This command is used to specify muting of the MASTER A and B with the 8-bit data. When you want to set the MUTING status, set the corresponding bit to 1. When you want to cancel MUTING, set the corresponding b it to 0. Bit-2 to bit-7 are fix ed all the time. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 0 0 0 0 ...

  • Sony RS-232C - page 47

    – 47 – P ANEL LOCK : 43[H] 4C[H] 43[H] 4B[H] ( ‘ CLCK ’ ) This command is used to set the P ANEL LOCK. • Packet f ormat 43[H] 4C[H] 43[H] 4B[H] “ parameter ” 0D[H] • Parameter Specify the setup or release of the P ANEL LOCK as the parameter . Example: When specifying release of the P ANEL LOCK. 43[H] 4C[H] 43[H] 4B[H] 4 0 [H] 0D[H] ...

  • Sony RS-232C - page 48

    – 48 – • INPUT Function 1 (1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23rd byte) This command is used to set the P ARALLEL INPUT function 1. • INPUT Function 2 (2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24th byte) This command is used to set the P ARALLEL INPUT function 2. The different functions ar e supported for the respectiv e values de pendi ...

  • Sony RS-232C - page 49

    – 49 – • OUTPUT Function 1 (25, 27, 29, 31, 33, 35, 37, 39, 41, 43rd byte) This command is used to set the P ARALLEL OUTPUT function 1. • OUTPUT Function 2 (26, 28, 30, 32, 34, 36, 38, 40, 42, 44th byte) This command is used to set the P ARALLEL OUTPUT function 2. The dif ferent functions are supported for the respectiv e values depending o ...

  • Sony RS-232C - page 50

    – 50 – P ARALLEL I/O P ARAMETER REQUEST : 52[H] 50[H] 49[H] 4F[H] ('RPIO') This command is used to read setup of the REMO TE P ARALLEL terminal from the SRP-X700P . • Packet f ormat 52[H] 50[H] 49[H] 4F[H] 0D[H] • Return packet f ormat When communication with the SRP-X700P is established with success, the parameter is returned tog ...

  • Sony RS-232C - page 51

    – 51 – REC OUT P ARAMETER REQUEST : 52[H] 4F[H] 4D[H] 33[H],32[H] ( ‘ ROR1,2 ’ ) This command is used to read parameter of the desired single channel of the REC OUT 1 and 2 from the SRP-X700P . The commands that correspond to the respectiv e channels are sho wn below . • Packet f ormat 52[H] 4F[H] 52[H] 31[H] “ parameter ” 0D[H] (In t ...

  • Sony RS-232C - page 52

    – 52 – • LINE3-4F machine type (1, 3, 5, 7, 9, 11 and 13th byte) This command is used to set category of the Control S. • LINE3-4F connection (2, 4, 6, 8, 10, 12 and 14th byte) This command is used to set the output channel of the CONTR OL S signal. • CONTR OL S I/F TYPE (15th byte) This command is used to set the connection type of the c ...

  • Sony RS-232C - page 53

    – 53 – • V ideo signal type (17th thr ough 22nd byte) This command is used to set the type of video signal of the equipment connected to LINE4 A to F . • Projector pr otocol (23rd byte) This command is used to select protocol of the projector to be connected. Bit 0 of the “ PJ CONTR OL ” changes depending on the protocol. Example: When ...

  • Sony RS-232C - page 54

    – 54 – R OUTING : 43[H] 52[H] 4C[H] 31[H]-38[H] ( ‘ CRL1-8 ’ ) 43[H] 52[H] 52[H] 31[H]-32[H] ( ‘ CRR1-2 ’ ) This command is used to set the routing for the OUTPUT channels. V arious setups can be memorized in the scene memories by specifying these scene Nos. The commands that correspond to the respecti ve channels are shown belo w . • ...

  • Sony RS-232C - page 55

    – 55 – • Lev el (2-17th byte) This command is used to set the ASSIGN le v el [dB]. • MIC1/WL1-MIC6/LINE2 ON/OFF (18th byte) This command is used to turn ON/OFF the routing of the MIC1/WL1 to MIC6/LINE2 with the 8-bit data. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 0 1 MIC6/ MIC5/ MIC4 MIC3 MIC2/ MIC1/ LINE2 LINE1 WL2 WL1 When you want to set ...

  • Sony RS-232C - page 56

    – 56 – R OUTING P ARAMETER REQUEST : 52[H] 52[H] 4C[H] 31[H]-38[H] ( ‘ RRL1-8 ’ ) 52[H] 52[H] 52[H] 31[H]-32[H] ( ‘ RRR1-2 ’ ) This command is used to read setup of the routing to the OUTPUT channels with the 8-bit data from the SRP-X700P . The commands that correspond to the respecti ve channels are shown belo w . • Packet f ormat 52 ...

  • Sony RS-232C - page 57

    – 57 – SCENE P ARAMETER REQUEST : 52[H] 53[H] 43[H] 52[H] ( ‘ RSTR ’ ) This command is used to read the setups of the functions of recalling at the e vent of scene recall from the SRP-X700P for all scene memories. • Packet f ormat 52[H] 53[H] 43[H] 52[H] 0D[H] • Return pack et format When communication with the SRP-X700P is established ...

  • Sony RS-232C - page 58

    – 58 – SCENE RECALL BUTT ON : 43[H] 52[H] 53[H] 41[H] ( ‘ CRSA ’ ) This command is used to set the scene No. to be recalled, to the SCENE RECALL A to D buttons on the front of the SRP-X700P . • Packet f ormat 43[H] 52[H] 53[H] 41[H] “ parameter ” 0D[H] • Parameter The parameter consists of the 4 bytes all the time in the order as sh ...

  • Sony RS-232C - page 59

    – 59 – SCENE RECALL BUTT ON P ARAMETER REQUEST : 52[H] 52[H] 53[H] 41[H] ( ‘ RRSA ’ ) This command is used to read the scene Nos. that are set to the SCENE RECALL A to D b uttons on the front of the SRP-X700P . • Packet f ormat 52[H] 52[H] 53[H] 41[H] 0D[H] • Return pack et format When communication with the SRP-X700P is established wit ...

  • Sony RS-232C - page 60

    – 60 – • Scene No. (1st byte) This command is used to specify the scene No. to be stored. • Function 1, 2 (10, 11th byte) This command is used to specify the function to implement recalling at the e vent of scene recall with the two 8-bit data. When you want to recall the scene, set the corresponding bit to 1. When you do not want to recall ...

  • Sony RS-232C - page 61

    – 61 – SPEAKER OUTPUT : 43[H] 4F[H] 53[H] 50[H] ( ‘ COSP ’ ) This command is used to set the SPEAKER OUTPUT . V arious setups can be memorized in the scene memories by specifying these scene Nos. • Packet f ormat 43[H] 4F[H] 4C[H] 33[H] “ parameter ” 0D[H] • Parameter The parameter consists of the 22 bytes all the time in the order ...

  • Sony RS-232C - page 62

    – 62 – A TT LEVEL A TT LEVEL A TT LEVEL 30[H] ( ‘ 0 ‘ )1 8 4 2 [ H ] ( ‘ B ’ )8 4 C [ H ] ( ‘ L ’ ) 30 39[ H] ( ‘ 9 ‘ )1 7 4 3 [ H ] ( ‘ C ’ )7 4 D [ H ] ( ‘ M ’ ) 27 3A [H] ( ‘ : ‘ )1 6 4 4 [ H ] ( ‘ D ’ )6 4 E [ H ] ( ‘ N ’ ) 25 3B [H] ( ‘ ; ‘ )1 5 4 5 [ H ] ( ‘ E ’ ) 5 4 F[H] ( ‘ O ’ ) 24 3C [H ...

Fabricant Sony Catégorie Music Mixer

Les documents que nous recevons du fabricant de l'appareilSony RS-232C peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Sony
- manuels d’utilisations RS-232C
- fiches produit Sony
- dépliants
- ou étiquettes-énergie Sony RS-232C
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Sony RS-232C.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Sony RS-232C, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Sony RS-232C. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Sony RS-232C.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Sony RS-232C, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Sony RS-232C par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Sony RS-232C.

Le manuel d’utilisation complet Sony, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Sony RS-232C - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Sony RS-232C, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lSony RS-232C qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Sony RS-232C - qui devraient nous aider dans les premières étapes lors de l'utilisation Sony RS-232C
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Sony RS-232C
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Sony RS-232C dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Sony RS-232C?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Sony RS-232C, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Sony RS-232C il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)