Manuel d’utilisation Vector VEC093

12 pages 0.23 mb
Télécharger

Aller à la page of 12

Summary
  • Vector VEC093 - page 1

    1 AUTOMA TIC BA TTER Y CHARGER OWNER’S MANUAL & W ARRANTY INFORMA TION 12 VOL T 2/1 0/20/40 AMPERE CHARGE RA TES WITH 1 00 AMP ENGINE ST AR T , AL TERNA TOR VOL T AGE CHECK AND BA TTERY RECONDITON FUNCTIONS • IMPORT ANT SAFETY INSTRUCTIONS • W ARNING – RISK OF EXPLOSIVE GASES 1. WORKING IN VICINITY OF A LEAD-ACID BA TTER Y IS DANGEROUS. ...

  • Vector VEC093 - page 2

    2 PERSONAL PRECAUTIONS AND SAFETY 1. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid batter y . 2. Have plenty of fresh water and soap nearby in case batter y acid contacts skin, clothing, or eyes. 3. W ear complete eye protection and clothing protection. Avoid touching eyes while work ...

  • Vector VEC093 - page 3

    3 PREP ARING TO CHARGE 1. Determine voltage of batter y by referring to car owner's manual. 2. If it is necessar y to remove batter y from vehicle to charge, or to clean terminals, always remove grounded terminal from batter y first. Make sure all accessories in the vehicle are off, so as not to cause an arc. 3. Clean batter y ter minals. Be c ...

  • Vector VEC093 - page 4

    4 INTRODUCTION AND FEA TURES Thank you for selecting the V ector(r) Model VEC093 2/1 0/20/40 Amp 12 volt Smart Batter y Charger with Engine Start, Alter nator V oltge Check and Batter y Restore modes. With proper care and use, it will give you years of depend- able ser vice. This model batter y charger has a high charge rate of up to 40 amps, and l ...

  • Vector VEC093 - page 5

    5 FIGURE 3A (FRONT VIEW) FIGURE 3B (REAR VIEW) W ARNINGS: • THERE ARE NO USER-SERVICEABLE P AR TS IN THIS UNIT . IN THE EVENT OF ANY OPERA TING PROBLEM THA T THE UNIT'S BUIL T -IN CIRCUIT PROTECTION CAN NOT HANDLE. • DO NOT OPEN THE UNIT . IT MUST BE RETURNED TO VECTOR FOR PROFESSIONAL TESTING AND REP AIR. OPENING THE UNIT WILL VOID THE MA ...

  • Vector VEC093 - page 6

    6 INDICA TORS THE LARGE 3-CHARACTER DIGIT AL DISPLA Y in the upper left hand corner of the panel indicates many conditions. It indicates when AC power is applied to the charger , actual charge rate in amperes, when the batter y is fully charged, detected faults, operating modes and when the charger is ready for the next mode selection. What is disp ...

  • Vector VEC093 - page 7

    7 CHARGE RA TE SELECTION VEC093 After the clamps are connected, plug in the charger to an AC outlet and the charger will show a circulating pattern on the Digital Display . This pattern indicates power is applied. Press the ON/OFF button to prepare the charger to change to an operating mode. Press the 2/1 0/20/40 A button and the charger will begin ...

  • Vector VEC093 - page 8

    8 CONNECTING IF BA TTER Y IS OUTSIDE OF VEHICLE a) Check polarity of batter y posts- For top-mounted batter y connectors, the positive post (marked POS, P , +) usually has a larger diameter than the Negative batter y post (marked NEG, N, –). For side-mounted batter y connections the Positive terminal is red, the Negative terminal is black. b) Att ...

  • Vector VEC093 - page 9

    9 This slowly (over 24 hours) removes the insulating buildup from the plates so the batter y can hold a full charge. Most automotive batteries (50 to 70AH) can be treated once to reduce the lead sulfate buildup. Smaller 12 volt batteries, such as found in jump starters can be treated for 12 hours. However , depending on the severity of lead sulfate ...

  • Vector VEC093 - page 10

    10 TROUBLESHOOTING - F AUL T LED LIT NOTE: Batteries below 4.0 V olts will not allow the charger to operate. Make sure the batter y has at least 4 V olts if charger will not charge. The following conditions may light the F AULT LED: • Poor connection to the batter y (or frame). • Charging too fast - Decrease Charge Rate - Press 2/1 0/20/40A Pus ...

  • Vector VEC093 - page 11

    11 APPENDIX A — CHARGING TIMES To calculate the approximate charging time required to fully charge a batter y , it is necessar y to determine the specific gravity (or , percent of batter y charge) using a hydrometer . Use this technique if batter y vent caps can be removed. Check each cell. If there is one cell with a ver y low specific gravity c ...

  • Vector VEC093 - page 12

    12 VECTOR 5 YEAR LIMITED W ARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of V ector Manufacturing, Ltd., regarding this product. There is no other warranty , other than described herein. This V ector Manufacturing, Ltd. product is warranted, to the original pur ...

Fabricant Vector Catégorie Automobile Battery Charger

Les documents que nous recevons du fabricant de l'appareilVector VEC093 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Vector
- manuels d’utilisations VEC093
- fiches produit Vector
- dépliants
- ou étiquettes-énergie Vector VEC093
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Vector VEC093.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Vector VEC093, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Vector VEC093. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Vector VEC093.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Vector VEC093, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Vector VEC093 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Vector VEC093.

Le manuel d’utilisation complet Vector, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Vector VEC093 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Vector VEC093, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lVector VEC093 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Vector VEC093 - qui devraient nous aider dans les premières étapes lors de l'utilisation Vector VEC093
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Vector VEC093
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Vector VEC093 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Vector VEC093?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Vector VEC093, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Vector VEC093 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (1)

Jose Antonio

Al intentar scanear me dice que conecte el scaner. Una y otra vez.