Français dropdown-ico

Manuel d’utilisation Weider WESY26331

32 pages 1.41 mb
Télécharger

Aller à la page of 32

Summary
  • Weider WESY26331 - page 1

    USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfac- tion through direct assistance from our factory . T O A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOMER HOT LIN ...

  • Weider WESY26331 - page 2

    2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBL Y . . . . . ...

  • Weider WESY26331 - page 3

    IMPORT ANT PRECAUTIONS 3 W ARNING : T o reduce the risk of serious injury , read the following important precautions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade ...

  • Weider WESY26331 - page 4

    4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. W idth: 64 in. Length: 70 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Weight Stacks Backrests Leg Press Plate Ab Pulley Station Thank you for selecting the versatile WEIDER ® PRO 3750 weight system. The weight system of fers a selec- tion o ...

  • Weider WESY26331 - page 5

    5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape. Note: Assembly will be more convenient if you have a sock ...

  • Weider WESY26331 - page 6

    1. Locate and open the parts bags labeled “FRAME ASSEMBL Y .” Insert six M8 x 63mm Carriage Bolts (49) up through the Press Base (13) and the Weight Base (14). Attach the Press Base (13) to the Weight Base (14) with two M8 x 67mm Bolts (55), two M8 W ashers (20), and two M8 Nylon Locknuts (40). Do not tighten the Locknuts yet. 2. Slide the Ab U ...

  • Weider WESY26331 - page 7

    4. Slide the Front Seat Frame (8) onto the indicated M8 x 63mm Carriage Bolts (49) in the Press Base (13). Hand tighten two M8 Nylon Locknuts (40) onto the Carriage Bolts. Do not tighten the Locknuts yet. Attach the other end of the Front Seat Frame (8) to the Leg Press Upright (4) with two M8 x 67mm Bolts (55), two M8 W ashers (20), and two M8 Nyl ...

  • Weider WESY26331 - page 8

    8. Lubricate the insides of the indicated holes in the T op Weights (24) with the included grease. Slide a T op Weight onto each set of W eight Guides (23). 9. Attach the T op Frame (2) to the Ab Upright (1) with two M8 x 67mm Bolts (55), two M8 W ashers (20), and two M8 Nylon Locknuts (40). Do not tighten the Locknuts yet. Attach the Butterfly Fra ...

  • Weider WESY26331 - page 9

    11 . Locate and open the parts bag labeled “ARM ASSEMBL Y .” Attach the Leg Press Plate (1 1) to the Adjustment T ube (10) with an M8 x 60mm Bolt (62), two M8 W ashers (20), and an M8 Nylon Locknut (40). Make sure that the Leg Press Plate and Adjustment T ube are oriented as shown. 12. Attach the Adjustment T ube (10) to the Leg Press Arm (9) w ...

  • Weider WESY26331 - page 10

    10 15. Attach a Press Arm (7) to one side of the Press Frame (12) with two M8 x 63mm Bolts (39) and two M8 Nylon Locknuts (40). Attach the other Press Arm (7) to the Press Frame (12) in the same manner . 16. Lubricate both axles on the Butterfly Frame (3). Identify the Right Fly Arm (5) and the Left Fly Arm (6). Slide the Left Fly Arm (6) onto the ...

  • Weider WESY26331 - page 11

    1 1 17. Wet the lower end of the Left Fly Arm (6) with soapy water . Slide a Large Pad (22) onto the Left Fly Arm. Repeat this step with the Right Fly Arm (5). 18. Locate and open the parts bags labeled “CABLE ASSEMBL Y”, “CABLES”, and “PULLEYS.” During steps 19 through 49, refer to the CABLE DIAGRAMS on pages 26 and 27 of this manual t ...

  • Weider WESY26331 - page 12

    12 20. Wrap the Butterfly Cable (89) around a 90mm Pulley (82) as shown. Attach the Pulley and a Cable T rap (80) to the bracket on the Leg Press Upright (4) with an M10 x 48mm Bolt (50) and an M10 Nylon Locknut (42). The Cable T rap must be oriented to hold the Cable in the groove of the Pulley . 21. Wrap the Butterfly Cable (89) under a 90mm Pull ...

  • Weider WESY26331 - page 13

    13 24. Identify the Rear Cable (87)—this is the short- est Cable. Remove the M8 x 69mm Shoulder Bolt (43) from the T op Frame (2). Loosen the indi- cated M8 Nylon Locknut (40). Attach the Rear Cable to the T op Frame with the M8 x 69mm Shoulder Bolt (43) and an M8 Nylon Locknut (40). Make sure the flat edge of the Cable is against the T op Frame. ...

  • Weider WESY26331 - page 14

    14 28. Identify the Press Cable (88)—this is the longest Cable. Attach the end of the Press Cable to the Large “U”-bracket (84) with an M8 Nylon Locknut (40) and an M8 W asher (20). Do not completely tighten the Locknut. It should be threaded onto the end of the Cable so that two threads are showing above the Locknut, as shown in the inset dr ...

  • Weider WESY26331 - page 15

    15 31. Route the Press Cable (88) over a 90mm Pulley (82). Attach the Pulley and a Cable T rap (80) to the lower hole in the Pulley Plates (31) with an M10 x 48mm Bolt (50) and the M10 Nylon Locknut (42). The Cable must be routed from the direction shown. Make sure that the Cable T rap is positioned to hold the Cable in place. 32. Route the Press C ...

  • Weider WESY26331 - page 16

    16 35. Route the Press Cable (88) over a 90mm Pulley (82). Attach the Pulley and a Cable T rap (80) to the indicated hole in the Press Frame (12) with an M10 x 82mm Bolt (66), an M10 W asher (38), and an M10 Nylon Locknut (42). 36. Wrap the Press Cable (88) around a “V”-pulley (81). Attach the “V”-pulley to the lower bracket on the Leg Pres ...

  • Weider WESY26331 - page 17

    17 39. Note: The 90mm Pulley (82) used in this step was attached in step 38. It is shown removed for easier part identification. Route the Press Cable (88) around the 90mm Pulley (82). Make sure that the Cable T rap (80) is turned to hold the Cable in place and that the Cable is routed as shown. T ighten the M10 x 120mm Bolt (74) and the M10 Nylon ...

  • Weider WESY26331 - page 18

    18 43. Route the High Cable (85) under a 90mm Pulley (82). Attach the Pulley and a Cable T rap (80) to the single hole end of the Pulley Plates (31) with an M10 x 48mm Bolt (50) and the M10 Nylon Locknut (42). Make sure that the Cable T rap is positioned to hold the Cable in place. 44. Wrap the High Cable (85) around a 90mm Pulley (82). Attach the ...

  • Weider WESY26331 - page 19

    19 47. Wrap the Low Cable (86) around a 90mm Pulley (82). Attach the Pulley and a Cable T rap (80) to the Ab Upright (1) with the M10 x 92mm Bolt (76) and an M10 Nylon Locknut (42). Make sure that the Cable T rap is in the indicated position. 48. Wrap the Low Cable (86) over a 90mm Pulley (82). Attach the Pulley and a Cable T rap (80) to the lowest ...

  • Weider WESY26331 - page 20

    50. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Small Backrest (18) to the Ab Upright (1) with two M6 x 63mm Machine Screws (64) and two M6 W ashers (37). 51. Insert an M6 x 52mm Carriage Bolt (61) through the center hole in a Seat Plate (41). Attach the Seat Plate to a Seat (17) with two M6 x 16mm Screws (59). Insert t ...

  • Weider WESY26331 - page 21

    54 55 56 21 57. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly , find and correct ...

  • Weider WESY26331 - page 22

    22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR- T ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the correct start- ing position for t ...

  • Weider WESY26331 - page 23

    23 A TT ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (35) to the Low Cable (86) at the ab pulley station with a Cable Clip (33). A TT ACHING AND REMOVING THE SEA T T o attach the Seat (17), set the bracket on the Rear Seat Frame (16) onto the pins on the Ab Upright (1). Attach the Rear Seat Frame to the Ab Upright with the M8 ...

  • Weider WESY26331 - page 24

    24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. The actual resistance at each weight station may vary due to differen ...

  • Weider WESY26331 - page 25

    T o tighten the cables, first insert the weight pin into the mid- dle of the weight stack. Slack can be removed from these cables several ways: • See drawing 1. T ighten the M8 Nylon Locknut (40) that connects the end of the Press Cable (88) to the Large “U”-bracket (84). • See drawing 1. Remove the M10 Nylon Locknut (42) and the M10 x 48mm ...

  • Weider WESY26331 - page 26

    26 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the High Cable (85), the Low Cable (86), the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89). Use the diagrams to be sure that the cables have been assembled correctly . The starting and ending points of each cable have been labeled. T ...

  • Weider WESY26331 - page 27

    27 High Cable (85) Rear Cable (87) Weight Stack— 5 High Pulley— 1 2 2 3 3 1 —T op Frame 4 —Weight Stack 4 ...

  • Weider WESY26331 - page 28

    M6 W asher (37) M10 Nylon Locknut (42) M8 Nylon Locknut (40) M6 Nylon Locknut (44) M8 W asher (20) M10 x 48mm Bolt (50) M10 x 60mm Bolt (65) M10 x 57mm Bolt (91) M8 x 63mm Bolt (39) M8 x 60mm Bolt (62) M8 x 45mm Bolt (68) M8 x 22mm Shoulder Bolt (51) M6 x 16mm Screw (59) M6 x 63mm Carriage Bolt (60) M6 x 52mm Carriage Bolt (61) M6 x 63mm Machine Sc ...

  • Weider WESY26331 - page 29

    M10 x 195mm Bolt (52) M10 x 82mm Bolt (66) M10 x 80mm Bolt (71) M10 x 120mm Bolt (74) M10 x 97mm Bolt (95) M10 x 92mm Bolt (76) M8 x 67mm Bolt (55) M8 x 152mm Bolt (67) M8 x 69mm Shoulder Bolt (43) M8 x 63mm Carriage Bolt (49) M8 x 70mm Carriage Bolt (77) ...

  • Weider WESY26331 - page 30

    P ART LIST—Model No. WESY26331 R0904A Key No. Qty . Description 1 1 Ab Upright 2 1 T op Frame 3 1 Butterfly Frame 4 1 Leg Press Upright 5 1 Right Fly Arm 6 1 Left Fly Arm 7 2 Press Arm 8 1 Front Seat Frame 9 1 Leg Press Arm 10 1 Adjustment Tube 1 1 1 Leg Press Plate 12 1 Press Frame 13 1 Press Base 14 1 Weight Base 15 1 Leg Lever 16 1 Rear Seat F ...

  • Weider WESY26331 - page 31

    1 2 3 4 5 6 7 7 8 9 10 1 1 12 13 14 15 16 17 18 19 17 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 29 29 30 31 32 32 33 34 35 36 21 21 85 85 87 86 31 41 41 86 87 88 88 89 89 56 76 82 38 42 20 55 55 76 50 38 55 20 56 42 82 80 42 42 50 40 69 40 69 67 67 40 68 20 40 40 20 68 40 67 40 40 67 42 50 82 58 55 20 55 20 49 56 58 91 42 40 20 55 20 76 ...

  • Weider WESY26331 - page 32

    ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-877-992-5999, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY26331) 2. The NAME ...

Fabricant Weider Catégorie Home Gym

Les documents que nous recevons du fabricant de l'appareilWeider WESY26331 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Weider
- manuels d’utilisations WESY26331
- fiches produit Weider
- dépliants
- ou étiquettes-énergie Weider WESY26331
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Weider WESY26331.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Weider WESY26331, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Weider WESY26331. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Weider WESY26331.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Weider WESY26331, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Weider WESY26331 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Weider WESY26331.

Le manuel d’utilisation complet Weider, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Weider WESY26331 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Weider WESY26331, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lWeider WESY26331 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Weider WESY26331 - qui devraient nous aider dans les premières étapes lors de l'utilisation Weider WESY26331
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Weider WESY26331
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Weider WESY26331 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Weider WESY26331?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Weider WESY26331, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Weider WESY26331 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)