Français dropdown-ico

Manuel d’utilisation Directed Electronics 225A

19 pages 2 mb
Télécharger

Aller à la page of 19

Summary
  • Directed Electronics 225A - page 1

    CONGRA TULA TIONS ENDP ANEL LA Y OUT FEA TURES / SPECIFICA TIONS ENDP ANEL LA Y OUT (cont.) INST ALLA TION TR OUBLESHOO TING WIRING TR OUBLESHOO TING (cont.) PO WER / GROUND TR OUBLESHOO TING (cont.) CONNECTIONS TR OUBLESHOO TING (cont.) CONNECTIONS (cont.) SYSTEM DIA GRAM 1 / 2 INPUTS / CONNECTIONS BLOCK DIA GRAM INPUTS W ARRANTY CONTENTS (clic k ...

  • Directed Electronics 225A - page 2

    The extended use of a high powered audio system may result in hearing loss or damage. While TUBE DRIVER systems are capable of "Concer t Le v el" volumes with incredible accuracy , they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians. Please observe all local sound ordinances. ...

  • Directed Electronics 225A - page 3

    1 Power Bandwidth: 5 Hz -50 KHz T otal Harmonic Distortion: 0.2% or less (A-weighted) Input T opology: Balanced Differential Input Sensitivity: 500mV - 12 volts RMS Input Impedance: 10K Ohms Output Impedance: 2 - 16 Ohms, bridged 4 - 32 Ohms Specifications The TD2200PRO and TD225A amplifiers represent a radical new approach to mobile audio. All vol ...

  • Directed Electronics 225A - page 4

    Fuse Requirements Recommended Fuse Rating f o r TD2200 i s 10 0 Amps Recommended Fuse Rating f o r TD225A is 10 0 Amps Y ou will need to install an in-line fuse or cir cuit breaker in the power wire within 18” of the battery . This fuse or circuit breaker pr otects your vehic le fr om fire in case the power wire shorts to the vehicle bod y . If y ...

  • Directed Electronics 225A - page 5

    Recommended MINIMUM Gauge 3 W arning! Amplifiers Generate Heat! Y ou can mount the TU B E D RIVER in any position, even upside-down. However , you m ust maintain pr oper airflow . Do not install your TU B E D RIVER under carpets or enclose it behind airtight panels. In trunk-mounted applications, be sure to provide venting for air circulation. Let ...

  • Directed Electronics 225A - page 6

    4 W arning! T o prevent a short to ground, disconnect the negative (-) terminal of the system’s battery before you begin. If the power cable shorts to ground, current will continue to flow until the short is opened, the main fuse blows, the battery explodes, or the wire melts. Reconnect the terminal only after y ou make all connections. Grounding ...

  • Directed Electronics 225A - page 7

    5 Follow these simple instructions and ref er to the diagram below to make your speaker connections: • Using at least 16 gauge wire, run wire from the speakers to the amplifier(s) using the same precautions that you followed for running the power , ground, and remote wires • Cut off excess wire • Use wire strippers to strip 1/4 inch of insula ...

  • Directed Electronics 225A - page 8

    6 Mixed Mono Output All multi-channel T UBE D RIVERS are capable of being bridged into a 4- Ohm mono output without switches or bridging modules. Y ou can achieve this mono channel by using the left positive (+) speaker connection and the right negative (-) speaker connection. (Refer to the end panel drawing on the next page.) Note: T otal bridged ...

  • Directed Electronics 225A - page 9

    Input Jacks Y our TUB E D RIVER includes both RCA and Mini-DIN (balanced) inputs. The supplied RCA connections allow you to use TU B E D RIVER with other brands of audio gear . Our Diff erential RCA inputs provide a dr amatic improv ement in noise reduction ov er standard RCA input types . Our fully balanced Mini-DIN connection system f eatures hig ...

  • Directed Electronics 225A - page 10

    8 Input Gain Control There is an Input Gain Control located on the end panel under the RCA input jacks. This is not a v olume control! This control matches the output signal voltage of the source unit to the amplifier inputs. By turning the control clockwise (to the right), the inputs of the amplifier become more sensitive and will allow a weak sig ...

  • Directed Electronics 225A - page 11

    HANDCRAFTED IN THE USA By Precision Power POWER CONNECT POWER W ARM UP 9 P o wer Side 1 3 2 1. PO WER A red light indicates that the amplifiier is turned on (After warm-up sequence). 2. W ARM UP A red light indicated that the tubes are warming up. (Refer to Pg. 4; Remote T urn-on) 3. PO WER / GR OUND After you have securely connected your power and ...

  • Directed Electronics 225A - page 12

    1. SPEAKER OUTPUTS/REMO TE(T urn on) After connecting remote and speaker wires plug in the connector here. 2. GAIN CONTR OL Use this control to match the output level of the head unit to the outputs of the amplifier 3. B ALANCED INPUT Plug in the mini-din output from the LDX-33 crossover , LD-3 line driver, or other balanced source here. 4. -12dB F ...

  • Directed Electronics 225A - page 13

    11 No Sound Amplifier T urning Down at Normal V olume Do you have 12V at the amplifier ’s connections? Is the W ARM UP LED illuminated? YES NO YES The warm up cycle can take up to 40 sec., Is there sound after that? Y ou’re done Is there signal on the RCA ’s? YES NO Does the amp remote (REM) have 12V? Check all connections. Repair as needed Y ...

  • Directed Electronics 225A - page 14

    12 No Sound in One Channel Amplifier T urning D ow n at High V olume YES Reverse the left and right inputs. Check the pre-amp (RCA/Mini-Din) cables for open connections and make corrections. Did you find open connections? NO Y ou’re done SOUND IS NO W IN... Opposite Channel Problem is in the speaker or speaker wire of the silent channel. Check sp ...

  • Directed Electronics 225A - page 15

    13 Noises While the Engine is On Alternator whine: This noise changes in frequency with engine RPM. Check for: . Excessive input le vel . High resistance in cabling or corr oded and/or loose connections . P olarity of the input cab les If the problem persists, check the whines and pops checklist below . Ticks/b uzz: This noise should go faster and ...

  • Directed Electronics 225A - page 16

    14 Noises While the Engine is On or Off System hiss: Distor tion: System hiss is a white noise that occurs even when the engine is off. It is usually due to excessively high gain settings. If the hiss is still audible when you disconnect the input cables from the amplifier , check the input level on the amplifier . If the hiss disappears when you r ...

  • Directed Electronics 225A - page 17

    15 eject VOLUME BASS TREBLE RIGHT LEFT BALANCE TRACK REVERSE FOWARD 1 2 3 4 8 7 6 5 PPI MAR KET ING DPT Trk 1 LD4 Source Unit TD2200 PRO LD3 Studio Driver System 6 Studio Drive r System 6 Subwoofer TD TD TD 2200 2200 FN-6 -2dB 0 dB IN + + + - - -2dB 0 dB - - - - Woofer Midrange Tweeter + FN-6 -2dB 0 dB IN + + + - - -2dB 0 dB - - - - Woofer Midrange ...

  • Directed Electronics 225A - page 18

    16 AMP RCA Right Input DIF. RCA Left Input INPUT ATTENUATION AMP Left Right MINI-DIN Input DIF. GAIN GAIN Left Right BALANCED/RCA Switch BALANCED/RCA Switch B A CK T O CONTENTS ...

  • Directed Electronics 225A - page 19

    Three-Y ear Limited U .S.A. W arranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. TUBE DRIVER warrants its products to be free from defects in materials and workmanship under normal use and service for a period of three (3) years from the date of original purchase when the unit i ...

Fabricant Directed Electronics Catégorie Portable CD Player

Les documents que nous recevons du fabricant de l'appareilDirected Electronics 225A peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Directed Electronics
- manuels d’utilisations 225A
- fiches produit Directed Electronics
- dépliants
- ou étiquettes-énergie Directed Electronics 225A
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Directed Electronics 225A.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Directed Electronics 225A, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Directed Electronics 225A. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Directed Electronics 225A.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Directed Electronics 225A, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Directed Electronics 225A par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Directed Electronics 225A.

Le manuel d’utilisation complet Directed Electronics, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Directed Electronics 225A - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Directed Electronics 225A, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDirected Electronics 225A qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Directed Electronics 225A - qui devraient nous aider dans les premières étapes lors de l'utilisation Directed Electronics 225A
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Directed Electronics 225A
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Directed Electronics 225A dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Directed Electronics 225A?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Directed Electronics 225A, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Directed Electronics 225A il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)