Français dropdown-ico

Manuel d’utilisation Fisher & Paykel DS602I

20 pages 1.26 mb
Télécharger

Aller à la page of 20

Summary
  • Fisher & Paykel DS602I - page 1

    DS602 I (Integrated) Models DS602 DS602 I DS602 (Prefinished) Part No. 599066/D USA ...

  • Fisher & Paykel DS602I - page 2

    Single DishDrawer Table of Contents Section 1 General Information 1.1 Preparation 1.2 Product Specifications & Cavity Dimensions 1.3 Options for Installing Multiple Products 1.4 Electrical, Plumbing & Drainage Information 1.5 Product Parts 1.6 Additional Product Parts for Integrated DishDrawer Section 2 Fitting the DishDrawer 2.1 DishDrawer ...

  • Fisher & Paykel DS602I - page 3

    Weight - Full 93lb (42kg) Prefinished - Empty 62lb (28kg) Prefinished Electrical 110-120VAC 3 pin socket outlet Drying Residual Heat & Fan Assisted Water Connection Recommended Hot 140 ° F (60 ° C) Max. Water Pressure Maximum 139 p.s.i. (960 kpa) Minimum 4.3 p.s.i. (30 kpa) GENERAL INFORMATION SECTION 1 The DishDrawer MUST be installed to all ...

  • Fisher & Paykel DS602I - page 4

    Page DS_03 Where the DishDrawer is in an under counter situation, i.e. built into a kitchen unit, it is recommended that bare wood surrounding the DishDrawer is sealed with an oil based paint or polyurethane to prevent possible steam damage. IMPORTANT IMPORTANT STEP 1.3 OPTIONS FOR INSTALLING MULTIPLE PRODUCTS IMPORTANT IMPORTANT IMPORTANT If mount ...

  • Fisher & Paykel DS602I - page 5

    Note: DS602 Prefinished Model is shown. There is no variation in plumbing between DS602 Prefinished Model and DS602I Integrated Model. Options 1 and 2 are the preferred options. PLUMBING - DRAINAGE OPTIONS Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service r ...

  • Fisher & Paykel DS602I - page 6

    Page DS_05 STEP 1.5 PRODUCT PARTS Tools Needed To Install DishDrawer  Wooden Chopping Board  Level  Safety Glasses  Utility Knife  Pencil  Drill & Drill Bits ( 3 / 32 ", 9 / 16 " & 11 / 32 ") (2.5mm, 12mm, 14mm)  Sandpaper  Tape Measure  Square  Ruler  Phillips Screwdriver  Pliers  Adjus ...

  • Fisher & Paykel DS602I - page 7

    SECTION 2 FITTING THE DISHDRAWER Ensure the cavity is at least 22 7 / 8 " (580mm) deep. TIP STEP 2.1 DISHDRAWER MOUNTING HOLE LOCATIONS 2.1.1 Draw the cavity center line on the supporting cabinetry. 2.1.2 Center Template in cavity using V-notch on the front of the Template. 2.1.4 Mark and drill four 15 / 32 " - 9 / 16 " (12mm-14mm) d ...

  • Fisher & Paykel DS602I - page 8

    STEP 2.2 CONNECTING THE SERVICES Ensure the edges of the Service Hole are smooth or covered. (See Step 1.2 - Product Specifications & Cavity Dimensions.) If the Services Hole is through a metal partition, the hole must be protected with the Edge Protector provided. DO NOT adjust the length of the Inlet Hose. Turn the water valve ON to check for ...

  • Fisher & Paykel DS602I - page 9

    The Product MUST NOT be plugged in at this stage. WARNING 2.2.6 If required, trim the Single Connector to the size which matches the waste tee or air break to be used. There are ribs provided to guide cutting. When using the Single Connector, the hose should be pushed in firmly, 5 clicks. Remember to slip the Wire Clip over the Drain Hose before co ...

  • Fisher & Paykel DS602I - page 10

    STEP 2.3 FLEXIBLE EXTRUSION ATTACHMENT FOR 24 (610mm) CAVITY Wiring, Plumbing and Services should be completed before attaching the flexible extrusion. TIP 2.3.1 Flexible Extrusions are supplied to enable the installer to help fill any excess space between the sides of the DishDrawer and the cavity. The two lengths of Flexible Extrusion (supplie ...

  • Fisher & Paykel DS602I - page 11

    SECTION 3 DO NOT push against the middle of the drawer. The DishDrawer should not support any part of the kitchen cabinetry. WARNING Make sure the inlet and drain hose and main flex are not restricted or damaged by carefully pulling them through the Services Hole as the DishDrawer is being pushed back into the cavity. IMPORTANT WARNING INSERTING DI ...

  • Fisher & Paykel DS602I - page 12

    Recommended Drawer Front thickness for Integrated product is 5 / 8 " to 3 / 4 " (16mm - 18mm). IMPORTANT SECTION 4 INFORMATION FOR CABINET MAKER FOR INTEGRATED DISHDRAWER STEP 4.1 INTEGRATED DRAWER FRONT DIMENSIONS Drawer Front material must be suitable for damp conditions or adequately sealed to withstand moisture. Additional protection ...

  • Fisher & Paykel DS602I - page 13

    A minimum clearance of 3 / 32  (2.5mm) must be maintained between the Drawer Front and existing cabinetry, except between the underside of the Drawer Front and the shelf, where a 1 / 4  (6mm) clearance is needed for product venting. IMPORTANT I N T E G R A T E D P R O D U C T O N L Y Page DS_12 Drawer Front Air Flow Chamfer Chamfer the back o ...

  • Fisher & Paykel DS602I - page 14

    Accuracy is essential when cutting the Badge Mounting Hole to ensure a neat fit to hold the badge. IMPORTANT IMPORTANT All marking out to be done on the back surface of the Drawer Front. When mounting the handle, ensure fastenings do not protrude beyond the back surface of the Drawer Front. I N T E G R A T E D P R O D U C T O N L Y Page DS_13 IMPOR ...

  • Fisher & Paykel DS602I - page 15

    I N T E G R A T E D P R O D U C T O N L Y Use of a depth gauge is recommended when drilling out holes for Drawer Front Mounting Panel. WARNING Page DS_14 4.1.5 Drawer Front Mounting Bracket Nut Holes Using a 11 / 32  (8.5mm) diameter drill bit, drill out the four screw holes in each door panel to a depth of 9 / 16  (14mm). Remove burrs. * The ...

  • Fisher & Paykel DS602I - page 16

    SECTION 5 STEP 5.1 CHANGING THE INTEGRATED BADGE ENCLOSURE INTEGRATED DRAWER FRONT INSTALLATION STEP 5.2 DISASSEMBLING THE INTEGRATED BADGE ASSEMBLY There are several different colored Integrated badges to choose from. They include black, chrome, satin & brass. Two color options are provided with your machine, other options are available from y ...

  • Fisher & Paykel DS602I - page 17

    WARNING CAUTION Take care not to damage front surface of panel. Ensure all cuts are straight and care is taken to avoid damage to the Drawer Front. Care should be taken in the following steps. Overtightening will damage the Drawer Front. CAUTION I N T E G R A T E D P R O D U C T O N L Y STEP 5.4 FITTING THE BADGE, HANDLE & MOUNTING PANEL TO THE ...

  • Fisher & Paykel DS602I - page 18

    STEP 5.5 FITTING THE DRAWER FRONT TO THE DISHDRAWER Use a small amount of liquid soap along the lip of the seal to aid the Drawer Front to slide on easily against the seal. The Electronics Board is an electrostatic sensitive device. Ensure you are adequately grounded when connecting or disconnecting the badge by wearing a grounding strap or by grou ...

  • Fisher & Paykel DS602I - page 19

    SECTION 6 FINAL FITTING FOR SINGLE DISHDRAWER 6.1.1 Check final fit of DishDrawer in cavity. 6.1.2 Tighten M8 bolts. Page DS_18 ...

  • Fisher & Paykel DS602I - page 20

    SECTION 12 FINAL CHECKS STEP 7.1 INSTALLATION WET TEST SECTION 7 STEP 7.2 TROUBLESHOOTING Water underneath DishDrawer, check the hose connections and hose for leaks. Water around water supply and drainage connections - check connections, existing plumbing and hoses for leaks. Excessive water remaining above the filter plate, after the rinse cycle, ...

Fabricant Fisher & Paykel Catégorie Dishwasher

Les documents que nous recevons du fabricant de l'appareilFisher & Paykel DS602I peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Fisher & Paykel
- manuels d’utilisations DS602I
- fiches produit Fisher & Paykel
- dépliants
- ou étiquettes-énergie Fisher & Paykel DS602I
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Fisher & Paykel DS602I.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Fisher & Paykel DS602I, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Fisher & Paykel DS602I. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Fisher & Paykel DS602I.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Fisher & Paykel DS602I, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Fisher & Paykel DS602I par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Fisher & Paykel DS602I.

Le manuel d’utilisation complet Fisher & Paykel, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Fisher & Paykel DS602I - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Fisher & Paykel DS602I, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lFisher & Paykel DS602I qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Fisher & Paykel DS602I - qui devraient nous aider dans les premières étapes lors de l'utilisation Fisher & Paykel DS602I
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Fisher & Paykel DS602I
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Fisher & Paykel DS602I dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Fisher & Paykel DS602I?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Fisher & Paykel DS602I, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Fisher & Paykel DS602I il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)