Français dropdown-ico

Manuel d’utilisation Onkyo TX-DS494

36 pages 1.94 mb
Télécharger

Aller à la page of 36

Summary
  • Onkyo TX-DS494 - page 1

    Contents Thank you for purchasing the Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. TX-DS494 Appendix T ...

  • Onkyo TX-DS494 - page 2

    2 1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructi ...

  • Onkyo TX-DS494 - page 3

    3 1. Warranty Claim You can find the serial number on the rear panel of this unit. In case of warranty claim, please report this number. 2. Recording Copyright Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder. 3. AC Fuse The fuse is located inside the chassis and is not user-service ...

  • Onkyo TX-DS494 - page 4

    4 Check that the following accessories are supplied with the TX-DS494. AM loop antenna × 1 FM indoor antenna × 1 (Connector will vary depending on model specifications) Remote controller × 1 (RC-443S for models other than North American models, RC-444M for North American models) 75/300 Ω antenna adapter × 1 Declaration of Conformity We, ONKYO ...

  • Onkyo TX-DS494 - page 5

    5 3. After batteries are installed and seated correctly, replace the compartment cover. Notes: • Do not mix new batteries with old batteries or different kinds of batteries. • To avoid corrosion, remove the batteries if the remote controller is not to be used for a long time. • Remove dead batteries immediately to avoid damage from corrosion. ...

  • Onkyo TX-DS494 - page 6

    6 Fr ont panel facilities Here is an explanation of the controls and displays on the front panel of the TX-DS494. SP SEL TUNING PRESET MEMORY SW MODE DIGIT AL INPUT FM MODE CLEAR ~ * !@ # $ % ^ & STANDBY/ON OFF ON POWER PHONES MASTER VOLUME BASS TREBLE AV RECEIVER TX - DS 494 FM AM PHONO C D TAPE VIDEO 1 DVD AB SPEAKERS DIMMER SURROUND DTS / VI ...

  • Onkyo TX-DS494 - page 7

    7 5 DISPLAY button Each time you press the DISPLAY button, the screen changes as follows: When an input source other than FM or AM is selected: Press the DISPLAY button once to initiate the program format display. Pressing the button again switches the display to the other display. * If the input signal does not have a program format, then this wil ...

  • Onkyo TX-DS494 - page 8

    8 Front panel facilities 7 DIMMER button Press to set the brightness of the front display. The brightness changes to normal and dim. • The dimmer control for the front display can also be performed by using the remote controller. 8 MASTER VOLUME dial The MASTER VOLUME dial is used to control the volume level. Turn the dial clockwise to increase t ...

  • Onkyo TX-DS494 - page 9

    9 Remote contr oller R C - 4 4 3 S R E M O T E C O N T R O L L E R INPUT SELECTOR MODE SLEEP DIMMER DISPLAY CD TAPE PHONO TUNER D V D VIDEO 1 VIDEO 2 SUR MODE SW MOD E AUDIO SEL TUNER PRESET STANDBY/ ON STANDBY/ ON DISC MU TING DVD CD TAPE VOLUME TOP MENU MENU CH SEL RETURN SET UP TEST TONE LEVEL ENTER 1 9 0 = ~ - ! 2 4 6 3 5 7 8 For detailed descr ...

  • Onkyo TX-DS494 - page 10

    10 Rear panel facilities • Insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment. • Do not bind audio/video connection cables with power cords and speaker cables. Doing so may adversely effect the picture and sound quality. 1 ANTENNA These terminals are for connecting th ...

  • Onkyo TX-DS494 - page 11

    11 Rear panel facilities p z (REMOTE CONTROL) Connect the Onkyo components that have z connectors such as a CD player, and cassette tape deck using the z cables provided with them. When these components are interconnected, they can be controlled from the remote controller provided with the TX-DS494. After connecting the z connectors, check the oper ...

  • Onkyo TX-DS494 - page 12

    12 Example of ho w to connect y our equipment Here is explanation of how to connect the main components to the TX-DS494 in the standard manner. There are many ways that any one component can be connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be thought of ...

  • Onkyo TX-DS494 - page 13

    13 Example of how to connect your equipment Connecting your audio components Connecting a turntable Using an RCA-type audio connection cable, connect the output terminal on the turntable to the PHONO L/R jacks on the TX-DS494. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack. Note: The TX-DS494 ...

  • Onkyo TX-DS494 - page 14

    14 Connecting a satellite tuner or television Using an RCA-type video connection cable, connect the video output terminal (composite) on the satellite tuner or television to the VIDEO 1 IN VIDEO jacks on the TX-DS494. If there is an S video output terminal on the satellite tuner or television, connect it to the VIDEO 1 IN S VIDEO jack using an S vi ...

  • Onkyo TX-DS494 - page 15

    15 Example of how to connect your equipment VCR (VIDEO 2) TV monitor or Projector (MONITOR OUT) Satellite tuner or TV (VIDEO 1) DVD player or LD player (DVD) Analog signal Signal flow Digital signal S video signal Coaxial plug Video Audio (L) Audio (R) Example of video equipment connections ANTENNA FM 75 AM IN IN IN L L R R FRONT CENTER SURR SUB WO ...

  • Onkyo TX-DS494 - page 16

    16 P ositioning speaker s This unit has two sets of speaker system terminals (for SPEAKERS A and SPEAKERS B). Before connecting the speakers, place them correctly by consulting the instruction manuals that came with them. For surround playback, the configuration and placement of your speakers are very important. Standard speaker system for reproduc ...

  • Onkyo TX-DS494 - page 17

    17 ANTENNA FM 75 AM REMOTE CONTROL CENTER SPEAKER SURROUND SPEAKERS R L IN IN IN L L R R FRONT CENTER SURR SUB WOOFER RL 1 2 COAXIAL OUT IN A B R L FRONT SPEAKERS R L R L VIDEO DIGIT AL INPUT MONITOR OUT S VIDEO DVD VIDEO 1 VIDEO 2 PHONO CD SUB WOOFER PRE OUT TA P E DVD VIDEO 2 VIDEO 1 R L OPTICAL MUL TI CHANNEL INPUT MONI- TOR OUT GND AC OUTLETS A ...

  • Onkyo TX-DS494 - page 18

    18 AM loop antenna Connecting antennas Connecting the AM loop antenna 1. Press down the lever. 2. Insert the end of the cable into the hole. 3. Release the lever. The lever will return to the original position. Either of the split ends of the AM antenna can be connected to either terminal. Unlike speaker cabling, there is no polarity for AM broadca ...

  • Onkyo TX-DS494 - page 19

    19 Connecting antennas To TV (or VCR) If the reception condition cannot be improved by adjusting the provided antenna, install an outdoor antenna and connect it to this unit. Connecting an FM outdoor antenna Please make sure that you follow the considerations: • Keep the antenna away from noise sources (neon signs, busy roads, etc.). • It is da ...

  • Onkyo TX-DS494 - page 20

    20 Connecting the po wer Turning this unit ON from an z -connected component When the DVD player, CD player or MD recorder connected with the TX-DS494 through z cables is turned on, the TX-DS494 automatically turns on and selects the source that was turned on. Turning the TX-DS494 off sets the z -connected DVD player, CD player or MD recorder to st ...

  • Onkyo TX-DS494 - page 21

    21 Speaker Setup You need to set up the speaker configuration for the speaker system connected to the SPEAKERS A terminals (see page 17). Notes: • The speakers cannot be set up for optimum audio reproduction if; – Headphones are connected (see page 8), or – The SPEAKERS B system is On (see page 7). • It is not necessary to set up again once ...

  • Onkyo TX-DS494 - page 22

    22 Selecting a sound sour ce Selecting a sound source 1. Press the desired input selector button. The selected source name appears in the display. If the TAPE button is pressed, either the TAPE or MD input which has been selected beforehand will be displayed. The TAPE and MD sources can be switched alternately by holding the TAPE button for about 2 ...

  • Onkyo TX-DS494 - page 23

    23 Selecting a sound source Setting the input signal format If the input source is DVD, CD, VIDEO 1, VIDEO 2 or TAPE, you can specify the input signal format. With the initial setting, AUTO is assigned to the DVD, CD and VIDEO 1 inputs, and ANALOG is assigned to the TAPE and VIDEO 2 inputs. You can change this according to the signal format of the ...

  • Onkyo TX-DS494 - page 24

    24 Tuning into a radio station 1. Press either the AM or FM input selector button. 2. Using the TUNING a/s buttons on the front panel, tune into the station you desire. When you tune into a radio station, TUNED indicator appears in the display. If you tune into an FM station in stereo, then FM STEREO indicator lights up. • The tuner frequency cha ...

  • Onkyo TX-DS494 - page 25

    25 Selecting a preset radio station 1. Press either the AM or FM input selector button. The display should show the currently selected frequency. If it displays the listening mode, press the DISPLAY button to display the frequency. 2. Using the PRESET ™ / £ buttons, select the number of the desired preset station. When using the remote controlle ...

  • Onkyo TX-DS494 - page 26

    26 T o enjo y Surr ound mode The TX-DS494 ’ s surround sound enables you to enjoy the presence of a movie theater or concert hall in your room. Before using a surround mode, make sure the speaker setup has been set (refer to page 21). The configuration of the speakers are very important for the surround sound. Refer to “ Positioning speakers ? ...

  • Onkyo TX-DS494 - page 27

    27 Input source signal format Analog PCM* 4 Dolby Digital* 5 dts MULTI CH* 6 Source software Tape, Record, CD, Audio DVD, Video DVD, LD, CD, LD, Video DVD Tuner Video DVD Digital satellite Video DVD Listening mode broadcast STEREO* 1 ●●●● PRO LOGIC II* 2 ●●● DOLBY D ● DTS ● ORCHESTRA* 3 ●● UNPLUGGED* 3 ●● ALL CH ST* 3 ●? ...

  • Onkyo TX-DS494 - page 28

    28 To enjoy Surround mode Selecting Onkyo ’ s surround modes 1. Press an input selector button to select the desired sound source. 2. Press the DSP button repeatedly until the desired surround mode name appears. The selected mode appears in the display. Each time you press the button, the surround mode changes as follows: 3. Play the selected sou ...

  • Onkyo TX-DS494 - page 29

    29 To record the input source signal you are currently watching or listening to Recording of video and/or audio signals can be performed on the components connected to the VIDEO 2 OUT and TAPE OUT (audio only) jacks. 1. Press an input selector button to select the input source to record. The input source is now selected and you may watch or listen ...

  • Onkyo TX-DS494 - page 30

    30 Using remote contr oller CD operation buttons TAPE operation buttons R C - 4 4 3 S R E M O T E C O N T R O L L E R INPUT SELECTOR MODE SLEEP DIMMER DISPLAY CD TAPE PHONO TUNER D V D VIDEO 1 VIDEO 2 SUR MODE SW MODE AUDIO SEL TUNER PRESET STANDBY/ ON STANDBY/ ON DISC MUTING DVD CD TAPE VOLUME TOP MENU MENU CH SEL RETURN SET UP TEST TONE LEVEL ENT ...

  • Onkyo TX-DS494 - page 31

    31 Using remote controller Controlling an Onkyo DVD player The z connector of the Onkyo DVD player must be connected to the TX-DS494 (refer to page 11). 1. Press the DVD MODE button. 2. Press the STANDBY/ON button to turn on the Onkyo DVD player. 3. Press the desired operation button. DVD operation buttons s : Starts playback of DVD. e : Stops play ...

  • Onkyo TX-DS494 - page 32

    32 Pre-pr ogramming remote contr oller (Nor th American models onl y) R C - 4 4 4 M R E M O T E C O N T R O L L E R INPUT SELECTOR MODE SLEEP DIMMER DISPLAY CD TAPE PHONO TUNER D V D VIDEO 1 VIDEO 2 SUR MODE SW MODE AUDIO SEL TUNER PRESET T V CABLE SATELLI T E VCR STANDBY/ ON STANDBY/ ON CH DISC MUTING DVD CD TAPE VOLUME TV/VC R TOP MENU MENU CH T ...

  • Onkyo TX-DS494 - page 33

    33 CODE LIST Brand TV VCR CABLE DVD SAT ADMIRAL 01-03 01 ——— AIWA — 02 ——— AOC 04 ———— AUDIO DYNAMIC — 03, 04 ——— BELL & HOWELL 01, 02 05 ——— BROKSONIC 04 06, 07 ——— CANON — 08, 09 ——— CITIZEN — 10 ——— CRAIG 05-08 10 ——— CROSLEX 09 ———— CURTIS MATHIS 04, 08, 10 02, 09, 11 ? ...

  • Onkyo TX-DS494 - page 34

    34 T r oubleshooting guide If a problem occurs while you are using the remote controller, first try to operate the controls on the front panel of the TX-DS494 to make sure that it is not due to a malfunction (or worn out batteries) in the remote controller. POWER No power. • Power cord is disconnected. ➞ Connect power cord (page 20). • There ...

  • Onkyo TX-DS494 - page 35

    35 Troubleshooting guide FM/AM TUNER AM stations cannot be received. • AM loop antenna is not attached. ➞ Connect the included AM loop antenna to the AM antenna terminals (page 18). Buzzing noise on AM (particularly conspicuous at night or with weak stations). • Noise from electrical apparatus such as fluorescent lamp. ➞ Move the AM loop an ...

  • Onkyo TX-DS494 - page 36

    http://www.onky o.co.jp/ HOMEP AGE SN 29343037 W0103-1 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8111 Fax: 072-833-5222 http://www.onkyo-intl.com ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com ONKYO ...

Fabricant Onkyo Catégorie Stereo Receiver

Les documents que nous recevons du fabricant de l'appareilOnkyo TX-DS494 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Onkyo
- manuels d’utilisations TX-DS494
- fiches produit Onkyo
- dépliants
- ou étiquettes-énergie Onkyo TX-DS494
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Onkyo TX-DS494.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Onkyo TX-DS494, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Onkyo TX-DS494. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Onkyo TX-DS494.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Onkyo TX-DS494, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Onkyo TX-DS494 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Onkyo TX-DS494.

Le manuel d’utilisation complet Onkyo, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Onkyo TX-DS494 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Onkyo TX-DS494, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lOnkyo TX-DS494 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Onkyo TX-DS494 - qui devraient nous aider dans les premières étapes lors de l'utilisation Onkyo TX-DS494
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Onkyo TX-DS494
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Onkyo TX-DS494 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Onkyo TX-DS494?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Onkyo TX-DS494, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Onkyo TX-DS494 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (1)

Martin Gómez

He conectado mi equipo onkyo tx da 494 y lo tengo conectado a un disco duro externo y antes m funcionaba bien el sonido ahora lo conecto y las películas en dts m las decteta bien y se oyen en dts pero las dolby digital m las detecta o bien por dolby prologi o bien dolby digital en estéreo por lo cual no se oye bien. Antes las decretaba en dolby digital no sé si esq tengo una mala conexión o q pasa, tengo el disco duro conectado al sonido por cable óptico si pueden ayudarme lo agradecería un saludo,