Français dropdown-ico

Manuel d’utilisation Oricom Secure 500

28 pages 0.53 mb
Télécharger

Aller à la page of 28

Summary
  • Oricom Secure 500 - page 1

    Baby Monitor Secure 500 User Guide ...

  • Oricom Secure 500 - page 2

    T ABLE OF CONTENTS W ARNINGS AND SAFETY INFORMA TION 1 GETTING ST ARTED 3 YOUR BABY MONITOR 6 LCD DISPLA Y OF BABY MONITOR 10 BASIC OPERA TION 11 MENU SETTINGS 18 TROUBLESHOOTING 23 PRODUCT SPECIFICA TIONS 24 GUARANTEE 25 ...

  • Oricom Secure 500 - page 3

    1 Do not place the cord in a high "wear and tear" location. Never use a frayed or compromised cord. Never use or place your Parent or Baby units in or near moisture or water (e.g. near bath or pool). Immersing in water can cause electric shock and even death. Power requirements This product requires an electrical supply of 220-240 volts, ...

  • Oricom Secure 500 - page 4

    2 W ARNINGS AND SAFETY INFORMA TION Battery requirements Each parent unit requires two rechargeable Ni-MH batteries, size AA 1.2V 1300mAh. • Do not dispose of the batteries in a fi re, as they can explode. • Do not open, unscrew or temper with any of your baby monitor units or battery. Always carry out repairs through your authorised ORICOM re ...

  • Oricom Secure 500 - page 5

    3 GETTING ST AR TED Installation and Charger For the Parent Unit 1. Remove the battery cover on the back of the Parent Unit by pressing and sliding it down. Insert the rechargeable batteries as marked on the unit and close the cover again. 2. Place the Parent Unit into the Charger Pod. 3. Plug the mains adaptor into a mains power socket. The red ch ...

  • Oricom Secure 500 - page 6

    4 4. Press [ ] to turn the Parent Unit on. • Before fi rst use, or if it has been out of use for a long time, the Parent Unit will need to be charged for 14 hours. During this time, the Parent Unit will operate from the Charger pod when switched on. Note that the Parent Unit cannot be used without batteries, even if it is placed in the charger p ...

  • Oricom Secure 500 - page 7

    5 GETTING ST AR TED Wall mounting the Baby Unit Use the following wall mount diagram to locate and install the mounting pins/screws if you prefer to wall mount your base unit. The dimensions are shown in millimeters (mm). Ø 4.00 Ø 7.55 58.00 1. Insert screws into the wall through the wall mount. The recommended mounting screw size is diameter 3mm ...

  • Oricom Secure 500 - page 8

    6 YOUR BABY MONITOR Baby unit (Sender) Page Press to page the Parent unit – useful for fi nding when it is misplaced. Record Used to record your voice to comfort your baby and to delete the recorded message. Power on/off Press to switch on or off. Link light Green when linked to Parent unit. Flashes if not linked - fi rst 30 seconds. Flashes wh ...

  • Oricom Secure 500 - page 9

    7 YOUR BABY MONITOR Back of Baby unit Underside Power socket For connection to mains power. Auxiliary input socket Use to plug in an external audio source, e.g. MP3 player so you can play your own choice of music to baby. Temperature sensor Battery lock Child tamper proof lock for the battery compartment. ...

  • Oricom Secure 500 - page 10

    8 Parent unit From the Parent unit you can listen to your baby and operate the Baby unit by remote control. Talk (on side of unit) Press to talk to your baby. LED Link indicator Green On – Linked to Baby unit Green fl ashing – Not linked to Baby unit – fi rst 30 seconds Red Flashing – Not linked to Baby unit – for longer than 30 seconds ...

  • Oricom Secure 500 - page 11

    9 Back of Parent unit Charging light Indicates parent unit is charging. Power socket For connection to mains power. YOUR BABY MONITOR ...

  • Oricom Secure 500 - page 12

    10 Speaker is switched off. Sound alert is on. Full battery Mid charge Low charge Empty Scrolling bars when charging. Night Light is on. Lullaby is playing. Temperature is within normal levels. Timer is on. Vibrate alert is on. Battery full (icon not displayed when using mains power). Battery half full. Battery low. Displayed when the Night Light i ...

  • Oricom Secure 500 - page 13

    11 BASIC OPERA TION Once you have set up your Baby Monitor, you will be able to hear the sounds in your baby's room through the Parent Unit. And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels. • If the connection between the Parent and Baby Units is broken at any time the green ...

  • Oricom Secure 500 - page 14

    12 BASIC OPERA TION • Audio picked up by the baby unit microphone is depicted on the 7 Lights on the parent unit (4 green and 3 red). The more audio is picked up, the more Lights will be lit. When no audio is picked up, all 7 Lights will be off. • If the volume of the Parent Unit is turned off, an alert will sound and the unit will vibrate if t ...

  • Oricom Secure 500 - page 15

    13 BASIC OPERA TION Talk Back You can use the talk back feature to talk to your baby. Whilst using Talk Back you will not be able to hear your baby until you release the [Talk] key. • Press and hold [TALK] key on the Parent unit to speak to baby. • "Talk" is shown on the display and the green link lights on both Units fl ash. • Tal ...

  • Oricom Secure 500 - page 16

    14 BASIC OPERA TION Follow the "Temperature setting" on the Menu Setting section to set the temperature range and temperature alert. Lullaby Your baby can be soothed to sleep by a gentle lullaby from the Baby Unit. Each lullaby is played repeatedly for 15 minutes. Select one of the fi ve melodies or select Play All for a medley of all 5 ...

  • Oricom Secure 500 - page 17

    15 BASIC OPERA TION • Press [ ] key repeatedly to select different lullabies. • Press [ ] key to play. Parent Unit • Press [Menu] key and use [ ] key to scroll to "Lullaby". • Press [ ] key to con fi rm. "Play?" is shown on the display. • Press [ ] key to play the Lullaby. • Or press [ ] key to select "Select N ...

  • Oricom Secure 500 - page 18

    16 BASIC OPERA TION Delete a recorded lullaby 1 . Press and hold [Rec]. After 2 seconds the display shows "Deleted". 2. Release [Rec]. • To avoid deleting a recorded message, press [ ] on the Baby unit to check whether the Own prompt is displayed. If Own is displayed in the lullaby list, there is a recorded message. Connect to an auxili ...

  • Oricom Secure 500 - page 19

    17 Parent Unit When the batteries on the Parent Unit reach a low level, the display will show Low Battery. The low battery alert tone will be emitted from the speaker every 60 seconds. Once the low battery level is reached, the parent unit should still be able to operate for approximately 1 hour and 30 minutes. The low battery alert message and ale ...

  • Oricom Secure 500 - page 20

    18 MENU SETTINGS Note: All Menu setting operations are only available on the Parent unit. During setting, press [Menu] key to exit. Night Light Setting You can turn on or off the Night Light on the baby unit via the parent unit. 1 . Press [Menu] key on the parent unit. The display is shown below: Light On? 2. Press [ ] key to select Night light on ...

  • Oricom Secure 500 - page 21

    19 MENU SETTINGS Sensitivity Setting You can adjust the sensitivity on Parent Unit to monitor the sound from the Baby Unit. For example, if your baby is a particularly quiet sleeper, you can increase the sensitivity levels so that you are sure to hear if baby disturbs or becomes uncomfortable. 1. Press [Menu] key on the parent unit and use [ ] or [ ...

  • Oricom Secure 500 - page 22

    20 MENU SETTINGS Setting Temperature Range You can select your own minimum and maximum room temperatures. The minimum temperature can be anywhere between 10 ˚ C and 19 ˚ C and the maximum temperature anywhere between 22 ˚ C and 30 ˚ C. Note the default setting is 14 ˚ C min. and 23 ˚ C max. 1. Press [MENU] key to scroll to "Temperature&q ...

  • Oricom Secure 500 - page 23

    21 MENU SETTINGS Activate count up timer The timer can count up from 1 second to 99 hours 59 minutes. The TIMER icon [ ] is displayed along with the countup time. 1. In the Timer setting menu, Press [ ]. 2. Use [ ] or [ ] key to select "Count up". Press [ ]. 3 . "Timer On?" is shown on the display, Press [ ] to con fi rm. Start ...

  • Oricom Secure 500 - page 24

    22 MENU SETTINGS Vibrate Alert Setting Vibrate alert is only available on the Parent Unit. You can turn on/off the vibrate alert through the menu. 1. Press [Menu], and use[ ] or [ ] key to select "Vibrate". The display is shown below: Vibrate 2. Press [ ], "Vibrate On?" or "Vibrate Off?" is shown on the display. 3. Pre ...

  • Oricom Secure 500 - page 25

    23 TROUBLESHOOTING Problem Possible cause(s) The red Power lights do not light on when you plug in. 1. Check if the units are properly connected to the power supply. 2. Check if the power is turned on. If not, Press [ ] to turn on the power. The green Link light on the Parent Unit is fl ashing and cannot hear the sounds from your baby's room. ...

  • Oricom Secure 500 - page 26

    24 PRODUCT SPECIFICA TIONS Feature Speci fi cations Operating Frequency 1.8 GHz Range Up to 300 m under optimum conditions. The range is reduced in buildings (up to 50 m) as a result of walls, doors etc. Power supply (Baby Unit/Parent Unit) Input: 100-240 V AC 50-60 Hz Output: 7.5 V DC , 500 mA, Non rechargeable batteries, baby unit (not included ...

  • Oricom Secure 500 - page 27

    25 GUARANTEE Warranty (Australia) (a) Warranty Oricom International Pty Ltd (Oricom) warrants that the product is free from defects in materials and workmanship for a period of 12 months effective from the date of purchase. This warranty in no way affects your statutory warranty under the Trade Practices Act 1974 or any other similar legislation. I ...

  • Oricom Secure 500 - page 28

    Australia Oricom International Pty Ltd Locked Bag 658 South Windsor, NSW 2756 Customer Support Email: support@oricom.com.au Web: www.oricom.com.au Phone: 1300 889 785 Fax: (02) 4574 8898 ...

Fabricant Oricom Catégorie Baby Monitor

Les documents que nous recevons du fabricant de l'appareilOricom Secure 500 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Oricom
- manuels d’utilisations Secure 500
- fiches produit Oricom
- dépliants
- ou étiquettes-énergie Oricom Secure 500
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Oricom Secure 500.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Oricom Secure 500, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Oricom Secure 500. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Oricom Secure 500.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Oricom Secure 500, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Oricom Secure 500 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Oricom Secure 500.

Le manuel d’utilisation complet Oricom, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Oricom Secure 500 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Oricom Secure 500, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lOricom Secure 500 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Oricom Secure 500 - qui devraient nous aider dans les premières étapes lors de l'utilisation Oricom Secure 500
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Oricom Secure 500
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Oricom Secure 500 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Oricom Secure 500?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Oricom Secure 500, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Oricom Secure 500 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)