Français dropdown-ico

Manuel d’utilisation Husqvarna K650

24 pages 2.55 mb
Télécharger

Aller à la page of 24

Summary
  • Husqvarna K650 - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h K650 Cut-n-Br eak Oper ator’ s manual (EP A) Please read the operator’ s manual carefully and mak e sure you understand the instructions before using the machine. ...

  • Husqvarna K650 - page 2

    2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Prote ...

  • Husqvarna K650 - page 3

    English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the power cutter? .................. ...

  • Husqvarna K650 - page 4

    4 – English WHA T IS WHA T? What is what on the power cutter? HUSQVARNA CONSTRUCTION PRODUCTS 1 Operator’ s manual (EP A) 2 Combination spanner 3 Air filter cov er 4 F ront handle and water tap 5 W ar ning decal 6 Choke 7 Stop s witch 8 Star t throttle lock 9 Throttle lock out 10 T ype plate 11 Cylinder cov er 12 Star ter handle 13 Star ter 14 ...

  • Husqvarna K650 - page 5

    English – 5 SAFETY INSTR UCTIONS Steps before using a ne w power cutter • Please read the operator’ s manual carefully and make sure you understand the instructions bef ore using the machine. • The machine is only designed f or cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes. • Check the asse ...

  • Husqvarna K650 - page 6

    6 – English SAFETY INSTR UCTIONS General safety precautions W ork area safety • K eep wor k area clean and well lit. Cluttered or dark areas invite accidents . • Ne ver use the machine indoors . Be aw are of the dangers of inhaling the engine’ s exhaust fumes. • Do not use the machine in bad weather , such as dense f og, rain, strong wind ...

  • Husqvarna K650 - page 7

    English – 7 SAFETY INSTR UCTIONS Fuel safety (Refuelling/Fuel mixture/Stora ge.) • Ne ver refuel the machine while the engine is running. • Make sure there is plenty of v entilation when refuelling or mixing fuel (gasoline and 2-stroke oil). • Mov e the machine at least 10 ft (3 m) from the refuelling point bef ore star ting it. • Ne ver ...

  • Husqvarna K650 - page 8

    8 – English SAFETY INSTR UCTIONS CA UTION! Nev er use a machine that has a f aulty muffler . Throttle loc kout The throttle trigger lock is designed to pre v ent accidental operation of the throttle. When the loc k (A) is pressed in this releases the throttle (B). The trigger lock remains pressed in as long as the throttle is pressed. When the g ...

  • Husqvarna K650 - page 9

    English – 9 SAFETY INSTR UCTIONS Throttle loc kout • Make sure the throttle control is loc ked at the idle setting when the throttle lock out is released. • Press the throttle lock out and make sure it retur ns to its original position when you release it. • Check that the throttle control and throttle loc kout mov e freely and that the ret ...

  • Husqvarna K650 - page 10

    10 – English SAFETY INSTR UCTIONS Blade vibrations The blades can become out of true and vibrate if a too high f eed pressure is used. A lower f eed pressure can stop the vibration. Otherwise replace the blades . See the instructions under the heading Assembling the b lades. The blades shall be intended f or the mater ial to be cut. Material Diam ...

  • Husqvarna K650 - page 11

    English – 11 SAFETY INSTR UCTIONS • Cut in the same direction when cutting into an e xisting cut. A void cutting at an angle to the previous cut otherwise there is a risk of the blade jamming or that the machine can ”climb in the cut”. • Alwa ys cut from top to bottom (A). Remov e the cutter and use a crowbar to remo ve the material that ...

  • Husqvarna K650 - page 12

    12 – English SAFETY INSTR UCTIONS General rules • Ne ver cut upw ards or tow ards you so that the kic kback zone becomes activ ely cutting. • Alwa ys hold the machine in a fir m grip with both hands. Hold it so that the thumbs and fingers grip round the handles. • K eep a good balance and a fir m foothold. • When cutting vertically , a ...

  • Husqvarna K650 - page 13

    English – 13 ASSEMBL Y Assembling the blades Husqv arna blades are especially man ufactured and appro ved f or freehand cutting with the K650 Cut-n-Break. The blades hav e integrated belt pulley halv es and are to be changed in pairs. • Loosen the bar nuts, unscre w the clamping screw anticlockwise a f ew turns and then refit the bar as far as ...

  • Husqvarna K650 - page 14

    14 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-strok e engine and must alwa ys been run using a mixture of gasoline and two-strok e engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, e ven small inaccurac ...

  • Husqvarna K650 - page 15

    English – 15 ST ARTING AND ST OPPING Bef ore star ting W ater connector Connect the water hose to the w ater supply . The water flo w is regulated using the water tap . Starting a cold engine Decompression v alve: Press in the v alve to reduce the pressure in the cylinder , this is to assist star ting the power cutter . The decompression v alve ...

  • Husqvarna K650 - page 16

    16 – English MAINTENANCE Inspecting and adjusting the drive belt • The drive belt is fully enclosed and well-protected from dust, dir t and mechanical damage when cutting. • Check the driv e belt adjustment by f eeling with your fingers as illustrated. A correctly adjusted drive belt should hav e about 5 mm of movement. • T o adjust the dr ...

  • Husqvarna K650 - page 17

    English – 17 MAINTENANCE • Pull off the cutting arm by pulling it straight f orwards , as illustrated. • Remov e the complete dr ive belt (D). • Loosen the six screws (F) holding the guards on the cutting arm. • Fit the new driv e belt (K). • Refit the guards and belt cov er. • The bar (M) must be positioned on plate (L) so that the ...

  • Husqvarna K650 - page 18

    18 – English MAINTENANCE Air filter Air filters must be regularly cleaned to remov e dust and dir t in order to av oid: • Carburettor malfunctions • Star ting problems • Less power • Unnecessar y wear to engine parts • Excessive fuel consumption. The air filter system consists of an oiled f oam plastic filter (1) and a paper filter ...

  • Husqvarna K650 - page 19

    English – 19 MAINTENANCE Star ter Changing a br oken or worn starter cord • Loosen the filter and cylinder cov er. • Loosen the screws that hold the starter against the crankcase and remov e the star ter. • Pull out the cord appro x. 30 cm (12 inches) and hook it into the notch in the rim of the pulley . Release the recoil spring by lettin ...

  • Husqvarna K650 - page 20

    20 – English MAINTENANCE Changing a br oken recoil spring • Undo the bolt in the centre of the pulley and remo ve the pulley . • Bear in mind that the return spr ing lies tensioned in the star ter housing. • Loosen the bolts holding the spring cassette. • Remov e the recoil spr ing by turning the star ter over and loosen the hooks, with t ...

  • Husqvarna K650 - page 21

    English – 21 MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder . 5 Cylinder cov er (directs cold air over the cylinder). Clean the co ...

  • Husqvarna K650 - page 22

    22 – English TECHNICAL D A T A ´®z+SNQ¶5[¨ ´®z+SNQ¶5[¨ T echnical data Cutting equipment Max. blade speed, rpm 6200 K650 Cut-n-break Engine Cylinder displacement, cu.in/cm 3 71 Cylinder bore, inch/mm 1,97/50 Stroke , inch/mm 1,42/36 Idle speed, r pm 2500 Recommended max. speed, r pm 9750 (+/- 250) Po w e r, k W 3,5 Ignition system Manuf a ...

  • Husqvarna K650 - page 23

    English – 23 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Constr uction Products are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine . In U .S. and Canada, new small ...

  • Husqvarna K650 - page 24

    ´®z+SNQ¶5[¨ 2009-01-10 ´®z+SNQ¶5[¨ 1151464-95 ! W ARNING! Cutting, especially when DR Y cutting, generates dust that comes from the material being cut, which frequentl y contains silica. Silica is a basic component of sand, quar tz, brick cla y , granite and numer ous other minerals and r ocks. Exposure to e xcessive amount of suc h dust ca ...

Fabricant Husqvarna Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilHusqvarna K650 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Husqvarna
- manuels d’utilisations K650
- fiches produit Husqvarna
- dépliants
- ou étiquettes-énergie Husqvarna K650
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Husqvarna K650.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Husqvarna K650, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Husqvarna K650. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Husqvarna K650.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Husqvarna K650, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Husqvarna K650 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Husqvarna K650.

Le manuel d’utilisation complet Husqvarna, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Husqvarna K650 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Husqvarna K650, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHusqvarna K650 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Husqvarna K650 - qui devraient nous aider dans les premières étapes lors de l'utilisation Husqvarna K650
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Husqvarna K650
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Husqvarna K650 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Husqvarna K650?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Husqvarna K650, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Husqvarna K650 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)