Français dropdown-ico

Manuel d’utilisation Desa FSBVBPC

32 pages 1.16 mb
Télécharger

Aller à la page of 32

Summary
  • Desa FSBVBPC - page 1

    CAST IRON STOVE AND B-VENT (FREEST ANDING FIREPLACE HEA TER) BURNER SYSTEM OWNER’S OPERA TION AND INST ALLA TION MANUAL NA TURAL GAS BURNER SYSTEM MODEL FSBVBNC PROP ANE/LP GAS BURNER SYSTEM MODEL FSBVBPC REMOTE READY Save this manual for future reference. IMPORTANT: This b-vent burner system must be installed into approved FM I cast iron stove b ...

  • Desa FSBVBPC - page 2

    2 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com SAFETY INFORMA TION 1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases unless a certified kit is used. 2. For propane/LP burner system, do not place propane/LP supply t ...

  • Desa FSBVBPC - page 3

    3 107600 OWNER’S MANUAL For more information, visit www.desatech.com PRODUCT IDENTIFICA TION Install and use stove and burner system with care. Follow all local codes. In the absence to local codes, use the current National Fuel Gas Code ANS Z223.1 , also known as NFPA 54* (USA) or the current CAN/CGA- B149[.1 or .2] Installation Codes (Canada) . ...

  • Desa FSBVBPC - page 4

    4 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com LOCATION AND SPACE REQUIREMENTS Determine the safest and most efficient loca- tion for your FMI B-vent freestanding stove. Make sure that rafters and wall studs are not in the way of the venting system. Choose a location where the heat output is not affected by ...

  • Desa FSBVBPC - page 5

    5 107600 OWNER’S MANUAL For more information, visit www.desatech.com STOVE BODY ASSEMBLY 1. Lift off corrugated box enclosing stove body crating. 2. Remove all screws fastening the wood frame enclosure. Spread wood frame open and lift away from plastic-bagged stove body . The bottom pieces of pallet wood will remain bolted to the stove body . 3. ...

  • Desa FSBVBPC - page 6

    6 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBL Y Continued 9. Attach stove door by inserting step bolt through door hinge pivot hole and into threaded hole in stove body (see Fig- ure 9, page 5 and Figure 1 1). Use an adjustable wrench or a 12mm socket to fast ...

  • Desa FSBVBPC - page 7

    7 107600 OWNER’S MANUAL For more information, visit www.desatech.com CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBL Y Continued Continued INSTALLING B-VENT BURNER SYSTEM INTO STOVE BODY 1. Carefully lift burner system and place into stove body from the rear of stove (see Figure 16). 2. Place gasket on top of burner system and align over venting ...

  • Desa FSBVBPC - page 8

    8 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBL Y Continued WARNING: Never touch the blower wheel while in operation. NOTICE: If installing blower in an existing stove burner system with gas connections, shut off gas sup- ply and disconnect burner sys- tem from ...

  • Desa FSBVBPC - page 9

    9 107600 OWNER’S MANUAL For more information, visit www.desatech.com INSTALLING REAR COVER 1 . Place rear cover behind stove body . Rear cover will rest on the bottom ledge of the stove body . 2 . Place wire harness from ON/OFF switch under the cast of stove body . 3. Using bolts provided, attach rear cover to back of stove body . See Figure 21. ...

  • Desa FSBVBPC - page 10

    10 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com Figure 23 - Typical B-Vent Installation WARNING: Installation should only be made by qualified per- sons who are familiar with the safety procedures required for the installation of the product, who are equipped with the proper tools and testing instruments, an ...

  • Desa FSBVBPC - page 11

    11 107600 OWNER’S MANUAL For more information, visit www.desatech.com VENTING INST ALLA TION Continued Figure 25 - Vertical Venting Configuration Through Chimney Figure 26 - Venting Through a Side Wall Continued CHECKING VENT CAPACITY Complete all gas piping, electrical, and vent connections. After adjusting the fireplace and lighting the main bu ...

  • Desa FSBVBPC - page 12

    12 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com HIGH ALTITUDE INSTALLATION Your FM I B-vent freestanding stove and burner system has been AGA tested and approved for elevations from 0-2000 feet and CGA certified for elevations from 0-4500 feet. When installing this stove and burner sys- tem at an elevation a ...

  • Desa FSBVBPC - page 13

    13 107600 OWNER’S MANUAL For more information, visit www.desatech.com STOVE AND B-VENT BURNER SYSTEM INST ALLA TION INSTALLING GAS PIPING TO FIREPLACE LOCATION WARNING: A qualified in- staller or service person must connect burner system to gas supply. Follow all local codes. CAUTION: For propane/LP units, never connect heater di- rectly to the p ...

  • Desa FSBVBPC - page 14

    14 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com Cap Pipe Nipple Tee Joint Pressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 PSIG (3.5 kPa) 1. Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping systems. Pressures in ...

  • Desa FSBVBPC - page 15

    15 107600 OWNER’S MANUAL For more information, visit www.desatech.com STOVE AND B-VENT BURNER SYSTEM INST ALLA TION Continued Continued 4. Check all joints of gas supply piping system. Apply commercial leak test so- lution to all gas joints. Bubbles forming show a leak. Correct all leaks at once. 5. Reconnect burner system and equip- ment shutoff ...

  • Desa FSBVBPC - page 16

    16 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1, GWMS2 WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures. WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire ha ...

  • Desa FSBVBPC - page 17

    17 107600 OWNER’S MANUAL For more information, visit www.desatech.com REMOVING/REPLACING GLASS DOOR CAUTION: Do not operate this burner system with a broken glass door panel or without the glass door panel securely in place. For replacement part in- formation see Replacement Parts , page 26. 1. Remove 2 bolts from bottom of stove (if still in pla ...

  • Desa FSBVBPC - page 18

    18 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with freestanding stove with burner system. 1. Remove glass door . See Removing/Re- placing Glass Door , page 17. 2. Place log #1 (back log) on top of g ...

  • Desa FSBVBPC - page 19

    19 107600 OWNER’S MANUAL For more information, visit www.desatech.com TO TURN OFF GAS TO APPLIANCE 1. Set selector switch, located on side of rear co ver , i n the “OFF” position. 2a. Open lower door panel. 2b . If Using Optional Hand-Held Remote: Set selector switch in the OFF posi- tion to pre vent draining battery . 3. T urn off all electr ...

  • Desa FSBVBPC - page 20

    20 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com 1. After lighting, let pilot flame bur n f or about one minute. T urn control knob on the control valv e to ON position. T urn flame adjustment knob any- where between HI and LO. Slide the selector switch to the REMO TE posi- tion. Note: The bur ners may light ...

  • Desa FSBVBPC - page 21

    21 107600 OWNER’S MANUAL For more information, visit www.desatech.com INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT ASSEMBLY The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if ne ...

  • Desa FSBVBPC - page 22

    22 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com CLEANING AND MAINTENANCE WARNING: Turn off burner sys- tem and let cool before cleaning. CAUTION: You must keep con- trol areas, burners, and circulat- ing air passageways of stove and burner system clean. Inspect these areas before each use. Have burner system ...

  • Desa FSBVBPC - page 23

    23 107600 OWNER’S MANUAL For more information, visit www.desatech.com TROUBLESHOOTING Note: All troubleshooting items are listed in order of operation. WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater. CAUTION: Never use a wire, needle, or similar object to clean pilot. This ...

  • Desa FSBVBPC - page 24

    24 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com OBSERVED PROBLEM Burner does not light after pilot is lit Delayed ignition burner Burner backfiring during combustion Slight smoke or odor during initial operation Heater produces a whistling noise when burner is lit Glass soots Burner system produces a clickin ...

  • Desa FSBVBPC - page 25

    25 107600 OWNER’S MANUAL For more information, visit www.desatech.com TROUBLESHOOTING Continued WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas su ...

  • Desa FSBVBPC - page 26

    26 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com SER VICE HINTS When Gas Pressure is Too Low • pilot will not stay lit • burners will have delayed ignition • burner system will not produce specified heat • propane/LP gas supply might be low (propane/LP units only) When Gas Quality is Bad • pilot wil ...

  • Desa FSBVBPC - page 27

    27 107600 OWNER’S MANUAL For more information, visit www.desatech.com SPECIFICA TIONS FSBVBNC FSBVBPC 21,000-30,000 Btu/h 20,000-28,000 Btu/h Gas Type Natural Propane/LP Ignition Piezo Piezo Manifold Pressure 3.5" w.c. 10.0" w.c. Minimum Inlet Supply Pressure 4.5" w.c. 11.0" w.c. Thermal Efficiency 70% 70% Dimension, Inches/mm ...

  • Desa FSBVBPC - page 28

    28 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com ILLUSTRA TED PA R T S BREAKDOWN FSBVBNC FSBVBPC L O H I P I L O T OFF ON 4 4 17 18 19 21 23 -1 23-4 23-2 23-3 27 4 22 10 5 11 8 1 9 25 4 13 14 15 20 20 21 4 16 29 28 4 3 6 26 2 24 7 12 ...

  • Desa FSBVBPC - page 29

    29 107600 OWNER’S MANUAL For more information, visit www.desatech.com P ARTS LIST FSBVBNC FSBVBPC This list contains replaceable parts used in your burner system. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY NO. PART NUMBER DESCRIPTION QTY. 1 106839-01 Firebox Assembly 1 2 106854-01 Gl ...

  • Desa FSBVBPC - page 30

    30 CAST IRON STOVE AND BURNER SYSTEM 107600 For more information, visit www.desatech.com ILLUSTRA TED PA R T S BREAKDOWN FMI STOVE (P)FC SERIES 1R 1C 1L 5 8 8 7-4 6 5 5 7-1 7-2 5 4 7-3 2 3 (Discarded During Assembly) ...

  • Desa FSBVBPC - page 31

    31 107600 OWNER’S MANUAL For more information, visit www.desatech.com P ARTS LIST FMI STOVE (P)FC SERIES This list contains replaceable parts used in your stove. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. * Included In Hardware Kit KEY PART NO. NO. DESCRIPTION QTY. 1C 104171-02 Top Grate ...

  • Desa FSBVBPC - page 32

    LIMITED WARRANTY B-VENT BURNER SYSTEM AND FMI STOVE CHASSIS DESA International warrants this product to be free from defects in materials and components for four (4) years from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim un ...

Fabricant Desa Catégorie Electric Heater

Les documents que nous recevons du fabricant de l'appareilDesa FSBVBPC peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Desa
- manuels d’utilisations FSBVBPC
- fiches produit Desa
- dépliants
- ou étiquettes-énergie Desa FSBVBPC
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Desa FSBVBPC.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Desa FSBVBPC, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Desa FSBVBPC. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Desa FSBVBPC.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Desa FSBVBPC, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Desa FSBVBPC par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Desa FSBVBPC.

Le manuel d’utilisation complet Desa, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Desa FSBVBPC - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Desa FSBVBPC, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDesa FSBVBPC qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Desa FSBVBPC - qui devraient nous aider dans les premières étapes lors de l'utilisation Desa FSBVBPC
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Desa FSBVBPC
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Desa FSBVBPC dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Desa FSBVBPC?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Desa FSBVBPC, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Desa FSBVBPC il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)