Français dropdown-ico

Manuel d’utilisation RIDGID R4330

28 pages 1.95 mb
Télécharger

Aller à la page of 28

Summary
  • RIDGID R4330 - page 1

    Y our new planer has been engineered and manufactur ed to our high standards for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-fr ee performance. WARNING: T o reduce the risk of injury , the user must r ead and understand the operator’ s manual before using this pr od ...

  • RIDGID R4330 - page 2

    2  Introduction....................................................................................................................................................................... 2  General Safety Rules ...................................................................................................................................... ...

  • RIDGID R4330 - page 3

    3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failur e to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . READ ALL INSTRUCTIONS  KN OW YO UR PO WE R TOOL . Rea d the oper at or ’ s man ua l carefully . Learn the tool’ s applications and limitations as well as ...

  • RIDGID R4330 - page 4

    4 SPECIFIC SAFETY RULES GENERAL SAFETY RULES  INSPECT TOOL CORDS PERIODICALL Y . I f da m- aged, have repaired by a qualified service technician at an auth ori zed ser vic e facil ity . The condu cto r with insu lat ion having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor . If repair or replac ...

  • RIDGID R4330 - page 5

    5 WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to cause cancer , birth defects or other reproductive harm. Some examples of these chemicals ar e: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • ...

  • RIDGID R4330 - page 6

    6 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer . Read The Operator’ s Manual Safety Alert No Hands Symbol SYMBOL NAME DESIGNA TION/EXPLANA TION V oltage Current Frequency (cycles per second) Po ...

  • RIDGID R4330 - page 7

    7 SYMBOLS SYMBOL SIGNAL MEANING SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts. WARNING: SA VE THESE INSTRUCTIONS CAUTION: ...

  • RIDGID R4330 - page 8

    8 ELECTRICAL EXTENSION CORDS Use only 3-wir e extension cords that have 3-prong gr ound- ing plugs and 3-pole receptacles that accept the tool’ s plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the curr ent that the tool will draw . An undersized extension cord will cause ...

  • RIDGID R4330 - page 9

    9 MOTOR SAFETY PROTECTION This motor should be blown out or vacuumed frequently to prevent sawdust buildup which can interfere with normal motor ventilation.  Connect this tool to a power sour ce with the appr opriate voltage for your model and a 15-amp branch circuit with a 15-amp time delay fuse or circuit breaker . Using the wrong size fuse c ...

  • RIDGID R4330 - page 10

    10 GLOSSAR Y OF TERMS Non-Through Cuts Any cutting operation where the blade does not extend completely through the thickness of the workpiece. Push Blocks (for jointer planers) Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid helps keep the operator's hands well away from the cutterhead. Push ...

  • RIDGID R4330 - page 11

    11 Fig. 3 FEA TURES PRODUCT SPECIFICA TIONS Feed Rate ............................................................... 26 FPM Input .................................. 120 V , 60 Hz, AC Only , 15 Amp No Load Speed ...................................10,000 r/min. (RPM) Max. Planing Height ..................................................... 6 in. Max ...

  • RIDGID R4330 - page 12

    12 FEA TURES KNOW YOUR PLANER See Figure 3. The safe use of this product requires an understanding of the information on the tool and in this operator’ s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. 15 AMP MOTOR The planer has a powe ...

  • RIDGID R4330 - page 13

    13 Fig. 5 LOOSE P ARTS The following items are included with the tool:  Blade / tool storage  Switch key  Hex key (4 mm)  Magnetic blade tool  Hex head screw (2)  Depth adjustment handwheel duSt hood hAndwheel knoB  Dust hood  Dust hood knobs (2)  Handwheel knob  Operator’ s manual hex heAd SCrew SwitCh key hex key m ...

  • RIDGID R4330 - page 14

    14 UNP ACKING This product r equir es assembly . NOTE: Every RIDGID ® Thickness Planer is tested at the factory to insure its performance. Y ou may see small amounts of wood dust and chips on your new planer .  Carefully lift the tool from the carton and place it on a level work surface. NOTE: This tool is heavy . T o avoid back injury , lift w ...

  • RIDGID R4330 - page 15

    15 ASSEMBL Y INST ALLING HANDWHEEL KNOB See Figure 7.  Locate the handwheel knob and scr ew fr om a mong the loose parts. Insert the screw through the hole in the handwheel and tighten screw secur ely .  Using the hex head screw , attach the depth adjustment handwheel securely to the planer . INST ALLING THE DUST HOOD See Figure 8. From the b ...

  • RIDGID R4330 - page 16

    16 ASSEMBL Y LEVELING THE T ABLE EXTENSIONS See Figure 9. The infeed and outfeed table extensions are attached to the planer . Shipped in a folded, upright position, the table extensions must be in the down position befor e planing can begin. For accurate planing, table extensions must be level with the planer table. NOTE: For optimum performance, ...

  • RIDGID R4330 - page 17

    17 OPERA TION WARNING: Do not allow familiarity with tools to make you careless. Remember that a car eless fraction of a second is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes r esulting ...

  • RIDGID R4330 - page 18

    18 OPERA TION on Fig. 10 SwitCh key oFF A VOIDING SNIPE Snipes, or depressions made at either end of a workpiece by cutter blades, can occur when the boar d is not pr operly supported. Although snipe may be barely noticeable, it is important to keep the workpiece parallel and flat with the planer table to minimize snipe. Butting workpieces end- to- ...

  • RIDGID R4330 - page 19

    19 Fig. 12 dePth GAuGe OPERA TION ADJUSTING THE PLANING DEPTH See Figure 11. The depth adjustment handwheel is used to set the amount of wood being removed in a planing pass. Never make a planing cut deeper than 1/8 in. for material up to 6 in. wide or 1/16 in. for material between 6 in. and 13 in. wide. NOTE: Do not continuously use the planer at ...

  • RIDGID R4330 - page 20

    20 OPERA TION  Push slightly on the board and allow the automatic feed to take the board.  Release the board to allow the automatic feed to funct ion properly. Do not push or pull on the workpiece.  Move to one side at the rear of the planer and receive the planed lumber by grasping it in the same manner as it was fed. Do not gras ...

  • RIDGID R4330 - page 21

    21 WARNING: Be for e per for mi ng any adj us tm ent , make sur e the tool is unplugged from the power supply and the switch is in the OFF position. Failure to heed this warning could result in serious personal injury . THICKNESS SCALE ADJUSTMENT See Figure 15. Located on the right fr ont of the planer , the thickness scale shows the depth of the f ...

  • RIDGID R4330 - page 22

    22 ADJUSTMENTS loCk nut StoP SCrew Fig. 17 rePlAne indiCA tor REPEA T -A-CUT ™ See Figure 17. Plane a scrap piece of wood and measure the depth of the finished piece. If an adjustment is needed:  Unplug the planer .  Pull the replane indicator straight out to r emove.  Using the hex key provided, remove the hex head screw from the depth ...

  • RIDGID R4330 - page 23

    23 MAINTENANCE WARNING: When servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty , also wear a dust mask. GENERAL MAINTENANCE Avoid using solv ...

  • RIDGID R4330 - page 24

    24 MAINTENANCE Fig. 19 CORD STORAGE See Figure 19. For convenience, your planer comes equipped with cord storage. When not in use, the power cord should be wrapped around the planer . CAUTION: Check extension cor ds before each use. If dam ag ed, re pl ace imm edi ate ly . Nev er us e to ol with a damaged cord since touching the damaged ar ea could ...

  • RIDGID R4330 - page 25

    25 MAINTENANCE BLADE REPLACEMENT See Figures 21 - 23. The planer is equipped with replaceable/disposable double- edged cutter blades attached to a rotating cutterhead. W orn cutter blades will af fect cutting accuracy and may pr oduce ridges on the workpiece.  Unplug the planer .  Lower the cutterhead assembly .  From the back of the plane ...

  • RIDGID R4330 - page 26

    26 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION S n i p e ( d e p r e s s i o n s a t e n d s o f workpiece) Dull cutter blades Incorrect butted stock Unit not securely mounted Replace or turn cutter blades. Butt pieces end-to-end as they are fed into planer . Tighten lag bolts. T orn grain T oo deep a blade setting W orkpiece being fed against ...

  • RIDGID R4330 - page 27

    27 W ARRANTY Proof of purchase must be pr esented when r equesting warranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID ® , Inc. All warranty communications should be directed to One W orld T echn ...

  • RIDGID R4330 - page 28

    28 OPERA TOR’S MANUAL 13 in. THICKNESS PLANER R4330 R4330 CUSTOMER SERVICE INFORMA TION For parts or service, contact your nearest RIDGID authorized service center . Be sur e to provide all r elevant information when you call or visit. For the location of the authorized service center near est you, please call 1-866-539-1710 or visit us online at ...

Fabricant RIDGID Catégorie Planer

Les documents que nous recevons du fabricant de l'appareilRIDGID R4330 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques RIDGID
- manuels d’utilisations R4330
- fiches produit RIDGID
- dépliants
- ou étiquettes-énergie RIDGID R4330
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation RIDGID R4330.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation RIDGID R4330, manuels d’entretien, brefs manuels ou manuels de l’utilisateur RIDGID R4330. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit RIDGID R4330.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil RIDGID R4330, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser RIDGID R4330 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs RIDGID R4330.

Le manuel d’utilisation complet RIDGID, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel RIDGID R4330 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières RIDGID R4330, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRIDGID R4330 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil RIDGID R4330 - qui devraient nous aider dans les premières étapes lors de l'utilisation RIDGID R4330
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de RIDGID R4330
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service RIDGID R4330 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de RIDGID R4330?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec RIDGID R4330, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec RIDGID R4330 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)