Manuel d’utilisation Omnimount Lift 42

20 pages 2.55 mb
Télécharger

Aller à la page of 20

Summary
  • Omnimount Lift 42 - page 1

    Lift 42 Motorized Flat Pane l Lift System with Universal Adapter. IMAGES MAY DIFFER FROM ACTUAL PRODUCT. INSTRUCTION MANUAL Lift 42 = L1-10235-PRO -101008vE PN # 10235 ULN # ...

  • Omnimount Lift 42 - page 2

    2 W ARNING – ENGLISH  WARNING! SEVE RE PE RS ONAL INJ URY AND PROPERT Y DAMAG E CAN RESULT FROM IMPROPER INSTALLA TION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.  If you do not understand the in structions o r have any concerns or ques tions, please contact a qualified instal ler. North Am e rica residents can contact OmniMo ...

  • Omnimount Lift 42 - page 3

    3 Contents Power cable 1 14 Motor cable 1 13 Screen Adapter 1 12 Vertical Exten sion Rails an d covers 2 11 Universal Adapter 1 10 Corner brackets 2 9 IR Receiver/Control switch 1 8 Remote Contr ol 1 7 Control Box 1 6 Top Plate 1 5 Screen Support 1 4 Bayonet Bracket 1 3 Lift Column 1 2 Base Mount 1 1 Contents 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ...

  • Omnimount Lift 42 - page 4

    4 Contents Monitor Kit: Parts M-A through M- N are used to connect the TV to the universa l adapter. Spacers ma y be necessary for a p roper fit with recessed m ounting holes or to allow access to TV inputs. Hex screws 1/4-20 x 1/2" 4 W Allen wrench 7/32” 1 X Allen wrench 5/32” 1 Y Felt corner cushions 4 V Square washers 4 U 2" x 1/4& ...

  • Omnimount Lift 42 - page 5

    5  PINCH POINT WARNING! • Improper construction o f lift enclosure can create dangerous pinch points . It is the responsibility of the installer to ensur e the intended use of this product does not create hazardous pinch zones. Ins tallation design should prevent users from inserting objec ts between moving parts and fixed ob jects! Fa ilure t ...

  • Omnimount Lift 42 - page 6

    6 Before Enclosure Con struction!  Assemble lift mechanis m and connect the TV to be used in the install to determine dime nsions for the lift enclosure prior to construction. Be sure to le ave room for adjustments If necessary. An out of cabinet assembly of t he mechanism can be done using steps 1,4, 6,8,9 and 10 in order. (H + 2”) (D + 2”) ...

  • Omnimount Lift 42 - page 7

    7 Measurements Required For Cabin etry Dimensions  Use previous page to find the minimum INTERIOR di mensions for custom enclosures. Height Width Depth ...

  • Omnimount Lift 42 - page 8

    8 Step 1 O 1 2 x4  Attach the Base B racket (1) to the Lift Column (2): • Using the sm all Hex wrench and 6mm x 20mm screws (O), connect the base bracket to the lift column. Note that one side is counter sunk to ensure flush installation of screws. Hand tighten all four scre ws before proceeding. If the height of the TV to be used is greater t ...

  • Omnimount Lift 42 - page 9

    9 Step 2 Q 3  Attach the Bayonet Bra cket (3) to the enclosure: • Using the #10 x ¾” sc rews (Q), attach t he bracket so that the top edge of the brackets back plate is 20” above the botto m mounting surface ( the bottom of the cabinet or top of the spacer b lock if used). x4 ...

  • Omnimount Lift 42 - page 10

    10 Step 3 Figure A Figure B 3 2  Secure Lift Column and Base Bracket in enclosure: • Gently glide the lift co lumn into place on the bayonet bracke t so that the tapered slots on the co lumn are secured to the extrusions on the bracket. Gently push down until the base bracket is touching the bottom of the enc losure. DO NOT ATTACH THE BAS E BR ...

  • Omnimount Lift 42 - page 11

    11 Step 4 x4 4 4 12 12 TOP S  Connect Sc reen Adap ter (12) to the Screen Support (4 ): • Use the la rge hex wrench to secure the screen adapter to the screen support using four 3/8-16 x ¾” screws (S) . Depending on TV size and mounting hole pattern the screen adapter can be vertically ad justed for optimal fit. ...

  • Omnimount Lift 42 - page 12

    12  Initialize the lift system: • Connect the motor cable to the control box and “pigtail” on the lift column as shown in figures A and B. • Connect the IR receiver/control switch and c ontrol box power as shown in figures C and D. • Once all the cables are properly connect ed, the lift must be initialized by pressing and holding the d ...

  • Omnimount Lift 42 - page 13

    13  Attach the Screen Support(4 ) and Top Plate(5) to the Lift Column(2): • Before attaching the top plate ensure t hat the rubber guide on the “pigtail” is secured in the square cut o ut on what will be the front of the lift col u mn (fig. A). Failure to do so may resu lt in damage to the wire. • Once the pigtail is secure, line up the ...

  • Omnimount Lift 42 - page 14

    14 Step 7 2 1 Q x4  Attach lif t assembl y to enclosu re base: • Using a level on the top p late ensure that the lift co lumn and assembly are level w ithin the enclosu re. Gently tap the base of the colu mn left or right to bring the top plate le vel. • Using four #10 x ¾” ( Q) screw s attach the base bracket and lift asse mbly to the en ...

  • Omnimount Lift 42 - page 15

    15 Step 8 11 M-A – M-L M-A – M-L 10 10 Note : IF MONITOR SCREWS “BOTTOM OUT” , THEN USE ADDITI ONA L WASHERS (not included) TO TAKE UP THE SLACK. TV  Attach the Universal Adapter to the TV: • Place the TV fa ce down on a protected su rface. • For larger TV’s, the vertical ra ils may need swapped out for the longer included rails. R ...

  • Omnimount Lift 42 - page 16

    16 Step 9 Figure B Figure A Figure C  Connect the TV and universal adapter to the lift column: • Partially in stall two ¼-20 x ½” (W) hex screws into t he top r ear of th e universal adapter (fig . A). • Lift and lock T V into position on sc reen adapter (fig . B). • Install two remaining hex scre ws through the screen adapter into the ...

  • Omnimount Lift 42 - page 17

    17 Step 10  Install universa l adapter rail covers : • Carefully at tach the correct pla stic cove rs to the univer sal adapter. ...

  • Omnimount Lift 42 - page 18

    18 Appendix  Using guide pins for a floating top: • The guide pins are recommended for use as a safety measure to pre vent pinch points. A te mplate has been inc luded to assist with guide pin use. • If the guide pins are to be used, make su re the top surf ace of the en cl osure will not be used as a load bearing surface. • Carefully cons ...

  • Omnimount Lift 42 - page 19

    19 Guide Pin/Top Plate Template ...

  • Omnimount Lift 42 - page 20

    20 OmniMount Systems , Inc . 8201 South 48th Street Phoenix, AZ 85044-5355 1-800-MOU NT-IT 1-800-668-6848 www.omnim ountpro.com Thank you for purchasing an OmniMount product. ...

Fabricant Omnimount Catégorie TV Mount

Les documents que nous recevons du fabricant de l'appareilOmnimount Lift 42 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Omnimount
- manuels d’utilisations Lift 42
- fiches produit Omnimount
- dépliants
- ou étiquettes-énergie Omnimount Lift 42
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Omnimount Lift 42.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Omnimount Lift 42, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Omnimount Lift 42. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Omnimount Lift 42.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Omnimount Lift 42, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Omnimount Lift 42 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Omnimount Lift 42.

Le manuel d’utilisation complet Omnimount, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Omnimount Lift 42 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Omnimount Lift 42, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lOmnimount Lift 42 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Omnimount Lift 42 - qui devraient nous aider dans les premières étapes lors de l'utilisation Omnimount Lift 42
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Omnimount Lift 42
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Omnimount Lift 42 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Omnimount Lift 42?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Omnimount Lift 42, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Omnimount Lift 42 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)