Français dropdown-ico

Manuel d’utilisation Leica TPS400

36 pages 0.93 mb
Télécharger

Aller à la page of 36

Summary
  • Leica TPS400 - page 1

    User Manual Mining Application Program English V ersion 1.0 TPS400 Series ...

  • Leica TPS400 - page 2

    TPS400 Mining Manual-1.0.0en 2 T o use equipment in the permitted manner , please refer to the detailed safety instructions in the TPS400 User Manual (English version). The quick way to start with the TPS400 Mining Programs. The quick way to start © 2003 Leica Geosystems AG Heerbrugg, ® All rights reserved. ...

  • Leica TPS400 - page 3

    TPS400 Mining Manual-1.0.0en 3 Contents - Overview Contents - Overview Introduction ......................................................................... 5 Peg Survey .......................................................................... 6 Front Line Peg .................................................................. 1 6 Grades ......... ...

  • Leica TPS400 - page 4

    TPS400 Mining Manual-1.0.0en 4 Contents Introduction ................................................ 5 How to use this manual ............................... 5 Symbols used in the sequence of operation .................................................. 5 Peg Survey ................................................. 6 Introduction .................. ...

  • Leica TPS400 - page 5

    TPS400 Mining Manual-1.0.0en Introduction 5 Introduction How to use this manual This manual describes the basic operation of the TPS400 Mining field programs. It shall be used together with a TPS400 instrument. For detailed description about the whole functionality of the TPS400 instrument please refer to the TPS400 User Manual. Symbols used in the ...

  • Leica TPS400 - page 6

    TPS400 Mining Manual-1.0.0en Peg Survey 6 Peg Survey Mining_z01 Introduction The application "Peg Survey" is used to establish a forward peg (point). It is used to control the intermediate horizontal angle between backsight and foresight points. It also checks the horizontal distances and heights of the backsight and foresight points. It ...

  • Leica TPS400 - page 7

    TPS400 Mining Manual-1.0.0en Peg Survey 7 Before starting Peg Survey Data uploading using "Mining Editor" • Station coordinates (East, North, Height, Grade elevation) • Backsight point coordinates (East, North, Height, Grade elevation) • T olerances, sequence, number of sets • Job definition Uploading of fixpoint coordinates, tole ...

  • Leica TPS400 - page 8

    TPS400 Mining Manual-1.0.0en Peg Survey 8 Start and execution Peg Survey > Step 3 Choose "Start" by pressing [F4], then enter point number (PtID) and instrument height (hi) for the station. The sign for the instrument height (hi) is normally negative. > Step 4 [SET] Set Point number (PtID) and instrument height (hi). [EXIT] Leaves & ...

  • Leica TPS400 - page 9

    TPS400 Mining Manual-1.0.0en Peg Survey 9 Error messages Number of sets: One set means to measure two times the backsight point and two times the foresight point in both faces. The meaning of set is described: Mining_z02 One Set The user must complete the number of sets as preset in the tolerance setting. FS BS T wo Sets I Set FS BS I Set II Set St ...

  • Leica TPS400 - page 10

    TPS400 Mining Manual-1.0.0en Peg Survey 10 Sequence: It defines the measuring sequence. Options: • BFFB Backsight-Foresight- Foresight-Backsight • BFBF Backsight-Foresight- Backsight-Foresight • BBFF Backsight-Backsight- Foresight-Foresight [OK] Leaves this dialog and proceed to the next dialog. Proceeding Peg Survey Sample dialog: Set 1 of t ...

  • Leica TPS400 - page 11

    TPS400 Mining Manual-1.0.0en Peg Survey 11 Proceeding Peg Survey , continued > Step 7 Enter a desired foresight point number (PtID). [OK] Saves the foresight point number and proceed to the measure dialog. Sample dialog: > Step 5 Enter the reflector height (hr) for the backsight point, if required. > Step 6 Aim at backsight point and measu ...

  • Leica TPS400 - page 12

    TPS400 Mining Manual-1.0.0en Peg Survey 12 Proceeding Peg Survey , continued [REJECT] Reject the measurement and measure the set again. [ACCEPT] Accept the result and continue with the next set. Sample dialog: > Step 8 Enter the reflector height (hr) for the foresight point, if required. > Step 9 Aim at foresight point and measure. [MEASURE] ...

  • Leica TPS400 - page 13

    TPS400 Mining Manual-1.0.0en Peg Survey 13 Results Sample dialog: T olerances dialog: • dHz: Residual on the horizontal angle • dHD: Residual on the horizontal distance • dH: Height residual • T olHz, T olHD, T olH: T olerances horizon- tal angle, horizontal distance and height • Set No: Set number [P AGE] Sample dialog: [OK] Leaves this ...

  • Leica TPS400 - page 14

    TPS400 Mining Manual-1.0.0en Peg Survey 14 Results, continued Sample dialog: [P AGE] Sample dialog: Result dialog: • mHz: Average intermediate horizontal angle between backsight point and foresight point • mHDBS/FS: Average horizontal distance (Backsight and Foresight) • mHBS/FS: A verage height (Backsight and Foresight) • Pt BS/FS: Point n ...

  • Leica TPS400 - page 15

    TPS400 Mining Manual-1.0.0en Peg Survey 15 Results, continued [OK] Quits the program. [EXIT] T erminates the measurement and returns to the start- up menu. The following result data are stored in the internal memory: Result: mHz: Average intermediate horizontal angle between backsight point and foresight point mHD: A verage horizontal distance (bac ...

  • Leica TPS400 - page 16

    TPS400 Mining Manual-1.0.0en Front Line Peg 16 Front Line Peg Introduction The application "FLP" is used to mark a new line peg (Front line peg). This application is similar to "Peg Survey" and there is only one set of measurement required . For a more detail explanation of "FLP", please refer to chapter "Peg Surv ...

  • Leica TPS400 - page 17

    TPS400 Mining Manual-1.0.0en Grades 17 Grades Mining_z04 Introduction "Grades" application is used to mark gradelines along the side walls of the mines (tunnels). It allows users to input the slope gradient and an offset concerning the grade point. It computes the stake out height difference. The program allows also to map the positions o ...

  • Leica TPS400 - page 18

    TPS400 Mining Manual-1.0.0en Grades 18 Start and execution Grades Menu dialog of "FLP": Sample dialog: If the slope gradient (station until foresight point) is the same like the slope gradient (backsight point until station) then continue direct with > Step 3 . Y ou can start Grades either by selecting it in the program or after measur ...

  • Leica TPS400 - page 19

    TPS400 Mining Manual-1.0.0en Grades 19 Mining_z06 Start and execution Peg Survey , continued Mining_z05 150 1 H New Gradeline > Step 1 Enter the slope gradient (proportion e.g. 1:150). Slope gradient explained: Gradeline > Step 2 Enter the height difference. Height difference explained: H: Current height of gradeline above mine floor dH: Heig ...

  • Leica TPS400 - page 20

    TPS400 Mining Manual-1.0.0en Grades 20 Gradeline Marking Sample dialog: > Step 4 Enter a desired point number (PtID). > Step 5 Aim at target point and measure. [MEASURE] or [DIST]/[REC] Measurement is triggered and stored in the internal memory . [PREV] Returns to the start of "Grades" application. For a new definition of slope grad ...

  • Leica TPS400 - page 21

    TPS400 Mining Manual-1.0.0en Grades 21 Results Grades computes the height difference (dHgt) between measure point and stake out point and the horizontal distance (dHD) along the foresight line. Height difference (dHgt) and horizontal distance (dHD) explained: Mining_z07 New Gradeline point Station Foresight Point dHD Station Foresight Point Mining_ ...

  • Leica TPS400 - page 22

    TPS400 Mining Manual-1.0.0en Grades 22 Results, continued Saving data The following result data are stored in the internal memory: Measurement data: PtID: Point number Hz: Horizontal angle V: V ertical angle HD: Horizontal distance SD: Slope distance dH: Height difference Coordinates of new gradeline point: E: Easting N: Northing H: Height Grades R ...

  • Leica TPS400 - page 23

    TPS400 Mining Manual-1.0.0en Offset 23 Offset Introduction "Offset" application is generally used to obtain sections of the tunnels for volume computation as well as mapping of the tunnels. It allows users to input offset value (left, right, up and down) and computes after measurement the actual coordinates of the tunnel walls. Known: • ...

  • Leica TPS400 - page 24

    TPS400 Mining Manual-1.0.0en Offset 24 Start and execution Offset Menu dialog of "FLP": Sample dialog: > Step 1 Enter a desired point number (PtID) and the offset value. > Step 2 Using for the offset definition. (Left, Up, Right, Down) (Left, Down, Right, Up) Y ou can start Offset either by selecting it in the program or after measu ...

  • Leica TPS400 - page 25

    TPS400 Mining Manual-1.0.0en Offset 25 Start and execution Offset, continued Definition of offset explained: Mining_z10 Up Down Right Left > Step 3 Aim at target point and measure. [MEASURE] or [DIST]/[REC] Measurement is triggered and stored in the internal memory . [EXIT] Leaves the application Offset and return to the menu dialog of "FLP ...

  • Leica TPS400 - page 26

    TPS400 Mining Manual-1.0.0en Offset 26 Results Saving data The following result data are stored in the internal memory: Measurement data: PtID: Point number Hz: Horizontal Angle V: V ertical Angle HD: Horizontal distance SD: Slope distance The measurement data are already corrected. Offset information: Offset: Of fset value OffsetDir: Of fset direc ...

  • Leica TPS400 - page 27

    TPS400 Mining Manual-1.0.0en Setting out 27 Setting out This program calculates the required elements to stakeout points from coordinates or manualy entered angles, horizontal distances and heights. Setting out differences can be displayed continuously . Setting out coordinates from memory Procedure: Select the point. [DIST] Starts measurement and ...

  • Leica TPS400 - page 28

    TPS400 Mining Manual-1.0.0en Setting out 28 Orthogonal setout The position offset between measured point and setout point is indicated in a longitudinal and transversal element. dLength: Longitudinal of fset: positive if nominal point further away . dTrav .: T ransversal offset, perpendicular to line-of-sight: positive if nominal point is to the ri ...

  • Leica TPS400 - page 29

    TPS400 Mining Manual-1.0.0en T ie Distance 29 T ie Distance The application Tie Distance computes slope distance, horizontal distance, height difference and azimuth of two target points measured online , selected from the Memory or entered using the Keypad . The user can choose between two different methods: Polygonal (A-B, B-C) Radial (A-B, A-C) P ...

  • Leica TPS400 - page 30

    TPS400 Mining Manual-1.0.0en T ie Distance 30 Softkeys - polygonal method: [NewPt 1] An additional missing line is computed. Program starts again (at point 1). [NewPt 2] Point 2 is set as starting point of a new missing line. New point (Pt 2) must be measured. [RADIAL] Switches to radial method. Softkeys - radial method: [NewPt 1] Determine new cen ...

  • Leica TPS400 - page 31

    TPS400 Mining Manual-1.0.0en Mining Editor 31 Mining Editor Introduction "Mining Editor" (PC Program Package) is a Windows-based program used for the data exchange between the TPS400 Series and the PC. Installation on the PC The installation program for the "Mining Editor" can be found on the CD-ROM supplied. Please note that th ...

  • Leica TPS400 - page 32

    TPS400 Mining Manual-1.0.0en Mining Editor 32 • Define and upload T olerances Defining tolerances, editing tolerances (password protected), uploading tolerances • Creating fixpoint files Creating and editing of fixpoint files (Coordinates) Program content, continued Practical Examples The following pages of the manual describe the functionality ...

  • Leica TPS400 - page 33

    TPS400 Mining Manual-1.0.0en Mining Editor 33 First Example (Creating fixpoint files, define tolerances, uploading) Creating fixpoint files > Step 1 Open a new file: File ! ! ! ! ! New > Step 2 Enter point number , coordinates, backsight reference point, grade elevation. > Step 3 Save the created coordinate list: File ! ! ! ! ! Save As In ...

  • Leica TPS400 - page 34

    TPS400 Mining Manual-1.0.0en Mining Editor 34 First Example (Creating fixpoint files, define tolerances, uploading), continued > Step 5 a) Select a tolerance type (Primary , Secondary , T ertiary). b) Enter the values for: • Horizontal Angle Limit • Horizontal Distance Limit • Height Limit Upload Fixpoints and T olerances to the instrument ...

  • Leica TPS400 - page 35

    TPS400 Mining Manual-1.0.0en Mining Editor 35 Second Example (Importing of fixpoints in ASCII format) Process import fixpoint files The "Mining Editor" allows to import fixpoint files in ASCII format. > Step 1 File ! ! ! ! ! Open > Step 2 ASCII-File search and select. > Step 3 Open the selected file. Follow the wizard onscreen in ...

  • Leica TPS400 - page 36

    Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) Phone +41 71 727 31 31 Fax +41 71 727 46 73 www .leica-geosystems.com Printed in Switzerland - Copyright Leica Geosystems AG, Heerbrugg, Switzerland 2003 Original text 734337-1.0.0en Leica Geosystems AG, Heerbrugg, Switzerland, has been certified as being equipped with a quality system which meets ...

Fabricant Leica Catégorie Tablet Accessory

Les documents que nous recevons du fabricant de l'appareilLeica TPS400 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Leica
- manuels d’utilisations TPS400
- fiches produit Leica
- dépliants
- ou étiquettes-énergie Leica TPS400
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Leica TPS400.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Leica TPS400, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Leica TPS400. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Leica TPS400.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Leica TPS400, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Leica TPS400 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Leica TPS400.

Le manuel d’utilisation complet Leica, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Leica TPS400 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Leica TPS400, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lLeica TPS400 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Leica TPS400 - qui devraient nous aider dans les premières étapes lors de l'utilisation Leica TPS400
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Leica TPS400
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Leica TPS400 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Leica TPS400?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Leica TPS400, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Leica TPS400 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)