Français dropdown-ico

Manuel d’utilisation Remington 500V

32 pages 1.17 mb
Télécharger

Aller à la page of 32

Summary
  • Remington 500V - page 1

    IMPORTANT: Read this manual and all labels carefully before operat- ing your powder actuated tool. This manual should always accompany the tool and be transferred with it upon change of ownership. Operating Instructions POWDER ACTUATED TOOL MANUFACTURERS´ INSTITUTE INC. ™ G 029 ® A N I N D E P E N D E N T L A B O R A T O R Y T E S T I N G F O R ...

  • Remington 500V - page 2

    2 106763 INDEX Warning: Safety Precautions ............................................................ 3-11 Why A Power Fastener Holds ............................................................. 12 Selecting Power Fasteners and Power Loads .................................... 13 Operation ......................................................... ...

  • Remington 500V - page 3

    3 106763 G 018 W arning: Saf ety Precautions IMPORTANT: Read these operating instructions carefully and com- pletely before trying to operate or service this tool. Improper use of this tool can cause serious injury or death from firing fastener into body or from flying debris. We expressly disclaim any liability for any injury to persons or damage ...

  • Remington 500V - page 4

    4 106763 G 018 Safety Precautions POWDER ACTUATED TOOLS IN USE WARNING ! 4. ALWAYS clear the work area on all sides and post appropriate warning signs on job sites. 1. NEVER place your hand over the muzzle. Accidental discharge can cause serious injury. HANDLING THE TOOL 2. NEVER place your finger on the trigger until the tool’s muzzle is against ...

  • Remington 500V - page 5

    5 106763 G 018 G 018 Safety Precautions 4. NEVER carry or pass a loaded powder actuated tool. NEVER point a powder actuated tool at anyone. 3. ALWAYS store UNLOADED powder actuated tool and power loads in a locked container. Keep power loads of different power levels in separate containers. 5. If the tool is dropped, inspect for damage and repair i ...

  • Remington 500V - page 6

    6 106763 TOO HARD Point flattens TOO SOFT Sinks in with average hammer blow ? ? ? TOO BRITTLE Surface shatters G 018 G 018 G 018 Safety Precautions 7. An operator taking medication should take extra precautions while handling the tool. NEVER drink alcoholic beverages or take medications which impair your vision, balance or judgement before using a ...

  • Remington 500V - page 7

    7 106763 CAST IRON GLASS TILE BRICK 482-33 G 018 G 018 G 018 G 018 Safety Precautions 3. NEVER make fastenings in spalled or cracked areas. 2. NEVER attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Materials of this type tend to shatter and cr ...

  • Remington 500V - page 8

    8 106763 TOO THIN WELD G 018 3/16" MIN 1/2" 1" Safety Precautions 7. DO NOT drive power fasteners into steel base material less then 3/16" thick, within 2" of a weld, within 1/2" of the edge or within 1" of another power fastener. 3" 3" 3" 6. DO NOT drive power fasteners into concrete less than thre ...

  • Remington 500V - page 9

    9 106763 POWER LOADS POWER LOADS GASOLINE GAS OLINE G 018 G 018 G 018 G 018 G 018 Safety Precautions 2. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Again press the tool firmly against the work surf ...

  • Remington 500V - page 10

    10 106763 G 018 POWER LOADS ONLY Safety Precautions 1 2 3 4 5 6 7 8 9 10 11 12 1 22 L E K C I N B R A S S C A L I B E R NOTE: Failure to start with the lowest power level can result in overdrive condition and will re- sult in damage to tool (See page 13). 2. Remington ® power load strips are available in three power levels – green (level 3), yel ...

  • Remington 500V - page 11

    11 106763 G 018 Safety Precautions 6. Power fasteners are a permanently installed fixture. An act of demolition is required for their removal. Appropriate safety precautions must be taken. 9. If work is interrupted for any reason, remove the power load strip before removing the power fastener. 8. Never pry a power load out of the strip. Prying can ...

  • Remington 500V - page 12

    12 106763 Wh y A P ower F astener Holds WHY A POWER FASTENER HOLDS IN CONCRETE The compression bond of the concrete to the power fastener accounts for the majority of the holding power. The fastener displaces the concrete which tries to return to its original form causing a squeezing effect. Maximum holding power is achieved when the depth of penet ...

  • Remington 500V - page 13

    13 106763 OVERDRIVE G 018 Selecting P o wer F asteners and P o wer loads FASTENING INTO CONCRETE The proper power fastener length can be determined by adding the thickness of the material to be fastened and the amount of fastener that will actually penetrate the concrete. The concrete must be three times as thick as the intended fastener penetratio ...

  • Remington 500V - page 14

    14 106763 Operation 1. Grasp barrel assembly and slide forward rapidly until it stops. Push barrel assembly back into tool to the closed position. This sets piston into firing position. 4. Place the muzzle of tool perpendicular to work surface without tilting the tool. Push tool against work surface until sliding action of barrel stops. 3. Select t ...

  • Remington 500V - page 15

    15 106763 Operation 5. Squeeze trigger to set power fastener. Be sure to keep pressure on tool during this operation. 7. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Again press the tool firmly agai ...

  • Remington 500V - page 16

    16 106763 Pa r ts List 500V Key Part No. No. Description Qty. 1 SF901011 Housing 1 2 450108 O-Ring 1 3 SF901800 Baffle Assembly 1 4 SF901010 Pawl Assembly 1 5 450005 Trigger 1 6 455000 Rocker Arm Assembly 1 7 455041 Rocker Arm Spring 1 8 455042 Rocker Arm Pin 1 9 456048 Screw 2 10 SF901700 Handle Pad Assembly 1 11 SF901600 Rear Pad and Power Indica ...

  • Remington 500V - page 17

    17 106763 2 3 1 5 8 4 7 6 32 33 11 9 9 30 29 10 34 31 21 22 14 15 12 13 16 26 23 25 24 19 20 17 18 27 28 Cleaning and Maintenance Clean tool after each days use. Disassemble and clean the barrel assembly with the wire brush provided with tool. Notice: Do not attempt to clean power load strip channel with wire brush. Apply good quality penetrating l ...

  • Remington 500V - page 18

    18 106763 T ool Disassembl y Figure 2 - Removing Key Stop Key Stop A. REMOVING BARREL ASSEMBLY 1. Using screwdriver, lift end of annular spring and rotate spring until key stop is uncovered (see Figure 1). WARNING: Always unload a powder actuated tool before disassembling, replacing barrel, cleaning, or assembling. 6. Pull piston assembly, using mo ...

  • Remington 500V - page 19

    19 106763 B. REMOVING HANDLE PAD ASSEMBLY 1. Loosen screw on back of handle pad assembly with 3mm hex wrench. Do not remove the screw from the assembly (see Figure 5). 2. Remove handle pad assembly. 3mm Hex Wrench Figure 5 - Removing Handle Pad Assembly Handle Pad Assembly C. REMOVING REAR PAD AND POWER INDICATOR ASSEMBLY 1. Keeping pressure agains ...

  • Remington 500V - page 20

    20 106763 Outer Liner Assembly E. REMOVING FIRING PIN 1. Slide firing pin guide back so the slot in the firing pin guide lines up with the slot in the outer liner assembly. 2. Pull the sear out of the aligned holes (see Figure 8). 3. Slide firing pin guide off of the outer liner assembly (see Figure 9). Pull the firing pin assembly with sear spring ...

  • Remington 500V - page 21

    21 106763 Figure 13 - Removing Outer Liner Assembly G. REMOVING ADVANCE BAR 1. Using a 3mm hex wrench, loosen screws on cover and remove. 2. Remove advance pin with hammer and punch. 3. Remove advance bar and spring. H. REMOVING BAFFLE ASSEMBLY 1. Loosen and remove baffle assembly and o-ring. Figure 11 - Removing Advance Bar Figure 12 - Removing Ba ...

  • Remington 500V - page 22

    22 106763 Note: Spring and plate are NOT reversible. Bent arm on spring must be toward plate. T ool Assembl y (Cont.) Baffle Assembly O-Ring Housing Handle Figure 15 - Inserting Baffle Assembly B. INSERTING BAFFLE ASSEMBLY 1. Insert baffle assembly with o-ring into handle and tighten (see Figure 15). Figure 16 - Replacing Advance Bar Screws Cover A ...

  • Remington 500V - page 23

    23 106763 Outer Liner Assembly Figure 19 - Replacing Sear Figure 18 - Replacing Firing Pin Guide, Firing Pin Assembly, Spring, Transfer Pin, and Push Pin Firing Pin Guide Sear Sear Spring Push Pin Firing Pin Assembly Transfer Pin Firing Pin Guide Outer Liner Assembly E. REPLACING FIRING PIN 1. Insert transfer pin and push pin into outer liner assem ...

  • Remington 500V - page 24

    24 106763 I. ASSEMBLING BARREL ASSEMBLY 1. Using moderate force, insert piston assembly into barrel (see Figure 23). H. ATTACHING HANDLE PAD ASSEMBLY 1. Place handle pad assembly onto housing body and tighten screw with 3mm hex wrench. Make sure rocker arm spring stays tight against the handle pad assembly while tightening screw. T ool Assembl y (C ...

  • Remington 500V - page 25

    25 106763 2. Insert plastic buffer into muzzle cap. 3. Screw muzzle cap to barrel assembly. 4. Firmly insert barrel into outer liner assembly with slot side down (see Figure 24). Figure 24 - Separating Barrel Assembly from Housing Muzzle Cap Plastic Buffer Barrel Assembly Piston Outer Liner Assembly Figure 25 - Replacing Key Stop Key Stop Annular S ...

  • Remington 500V - page 26

    26 106763 PROBLEM Piston hangs out of muzzle. Overdriven fastener. Piston jammed. Power load strip will not advance. Reduction or loss of power. Tool does not com- pletely depress. Tool does not fire. Opening and closing of barrel or pushing down on tool, etc. is not smooth but is rough or binds. POSSIBLE CAUSE Tool overdriven. Piston not properly ...

  • Remington 500V - page 27

    27 106763 Te c hnical Service You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at www.desatech.com or contact our Technical Service Department at 1-800-858-8501 (English Only). You may also write to: DESA Specialty Products™ P.O. Box 90004 Bowling Green, K ...

  • Remington 500V - page 28

    Pa r ts Centrals Ray’s Portable Heater Service 3191 Myers Road Camino, CA 95709-9550 530-644-7716 Baltimore Electric 5 Manila Drive Hamden, CT 06514-0322 203-248-7553 1-800-397-7553 Eckley’s Small Engine 31617 Spruce Drive Eustis, FL 32726-9592 352-357-6764 Parts Company of America 1657 Shermer Road Northbrook, IL 60062-5362 708-498-5900 1-800- ...

  • Remington 500V - page 29

    Application Char t 2 1 / 2 " 2 1 / 2 " 2" 1" 1" 1" to this Concrete Cement Block Steel (3/16" to 3/8" Thick) Yellow Green Yellow/Red power load color power fastener length Power load and power fastener application information. Yellow Yellow Yellow/Red For fastening this Two by Fours Electrical Junction Boxes ...

  • Remington 500V - page 30

    30 106763 NO TES ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ __________________ ...

  • Remington 500V - page 31

    31 106763 NO TES ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ ____________________ __________________ ...

  • Remington 500V - page 32

    Limited W arranty Agreement DESA Specialty Products™ warrants the Remington ® Power Pro™ Model 500V against defects in materials and workmanship for a period of one (1) year from the date of purchase. If within one (1) year from the purchase date this Powder Actuated Tool fails due to a defect in material or workmanship, DESA Specialty Product ...

Fabricant Remington Catégorie Drill

Les documents que nous recevons du fabricant de l'appareilRemington 500V peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Remington
- manuels d’utilisations 500V
- fiches produit Remington
- dépliants
- ou étiquettes-énergie Remington 500V
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Remington 500V.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Remington 500V, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Remington 500V. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Remington 500V.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Remington 500V, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Remington 500V par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Remington 500V.

Le manuel d’utilisation complet Remington, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Remington 500V - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Remington 500V, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRemington 500V qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Remington 500V - qui devraient nous aider dans les premières étapes lors de l'utilisation Remington 500V
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Remington 500V
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Remington 500V dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Remington 500V?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Remington 500V, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Remington 500V il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)