Manuel d’utilisation Honeywell CT87A

12 pages 0.29 mb
Télécharger

Aller à la page of 12

Summary
  • Honeywell CT87A - page 1

    ® U.S. Registered Trademark Copyright © 2002 Honeywell All Rights Reserved 69-0274-6 Verify that you have the correct thermostat Using the compatibility chart below , verify that you purchased the correct CT87 Thermostat for your heating/cooling system. If you are unsure which model is right for your system, visit www .honeywell.com/ yourhome or ...

  • Honeywell CT87A - page 2

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 2 Prepare for installation 1. Carefully unpack your new thermostat; rough handling may affect it s accuracy . Save your receipt and identify the following parts: • CT87 Thermostat • Screws: two 1-in. sheet metal screws, two 1/2-in. binding head screws, and two 1/4-in. round head screws • W allplate (CT8 ...

  • Honeywell CT87A - page 3

    CT87A,B,J ROUND® THERMOSTAT 3 69-0274-6 5. Label the wires using the wiring labels that came with the CT87. Identify each wire using the letter of the terminal on th e old the rmo- stat (Fig. 2). Do not label the wires by color . 6. Disconnect the wires from the o ld thermostat and wrap them around a pencil to keep them from falling back into the ...

  • Honeywell CT87A - page 4

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 4 1. If using the cover ring: Position the cover ring again st the wall so that the arrow in the middle of th e cover ring is pointing up. 2. Position the wallp late or subbase . • If using cover ring : Place the wallplate/subbase over the cover ring. Rotate the wallpl ate/subbase until the wiring o penings ...

  • Honeywell CT87A - page 5

    CT87A,B,J ROUND® THERMOSTAT 5 69-0274-6 1. Place the cover ring against the outlet box so that the arrow in the middle of the cover ring is pointing up. 2. Pull the wires through the wiring hole on the bottom left side of the cover ring. 3. Align the screw slots on the cover ring with the outlet box screw holes, and attach the cover ring to the ou ...

  • Honeywell CT87A - page 6

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 6 Wire the thermostat 1. Use the wiring cross-reference table below to match each old thermostat wire with its corresponding terminal on the CT87 wallpl ate or subbase. See Fig. 8 through 13 wiring diagrams. *Never attach wires to both the B and O terminals. 2. S trip the wire insulation as needed to fit the w ...

  • Honeywell CT87A - page 7

    CT87A,B,J ROUND® THERMOSTAT 7 69-0274-6 Fig. 8. CT87A for a 2-wire heat ing only system. Fig. 9. CT87A for a 3-wire hot water heating only system . Fig. 10. CT87B for a 4-wire heat ing/cooling system . M2018 3 CT87A WALLPLATE TO SYSTEM R W Y POWER HEAT M2018 4 WIRE LABELS (LETTERS ON ORIGINAL THERMOSTAT TERMINALS) CT87A WALLPLATE 3-WIRE HOT WATER ...

  • Honeywell CT87A - page 8

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 8 Fig. 1 1. CT87B for a 5-wire heating /cooling system. Fig. 12. CT87J for a 4-wire single stage heat pump. Fig. 13. CT87J for 4-wire single stage heat pump. C O O L • O F F • H E A T F A N O N • A U T O M2022 5 HEATING POWER CT87B SUBBASE TO SYSTE M TO SYSTEM R H G R C W Y FAN HEAT COOLING POWER COOL C ...

  • Honeywell CT87A - page 9

    CT87A,B,J ROUND® THERMOSTAT 9 69-0274-6 Mount the thermostat 1. Pull off the thermostat cover and discard the red plastic insert that holds the mercury switch in place during shipping. 2. Using a pencil po int, slide the heat anticipator indicato r to 1.2 on the scale as shown in Fig. 14. IMPORT ANT : This prevents the thermostat from being damage ...

  • Honeywell CT87A - page 10

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 10 Set the heat anticipator for your system IMPORT ANT : Setting th e heat anticipator allows the thermostat to maintain accurate temperature control. 1. Using a pencil point, move the heat anticipator pointer to the numbe r that you recorded in S tep 3, su b- step 3. If you could not find the anticipator sett ...

  • Honeywell CT87A - page 11

    CT87A,B,J ROUND® THERMOSTAT 1 1 69-0274 -6 Check cooling IMPORT ANT : T o a void damaging the compressor in the air conditioner , do not operate the cooling system when the outdoor temp erature is below 50°F (10°C). 1. If your CT87 has a subbase, set the System switch on the left to Cool. IMPORT ANT : Af ter heating is teste d, wait five minutes ...

  • Honeywell CT87A - page 12

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 G .H. Rev . 08-02 www .honeywell.com/yourhome Automation and Control Solutions Honeywell Honeywell Limi ted-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. H ...

Fabricant Honeywell Catégorie Thermostat

Les documents que nous recevons du fabricant de l'appareilHoneywell CT87A peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Honeywell
- manuels d’utilisations CT87A
- fiches produit Honeywell
- dépliants
- ou étiquettes-énergie Honeywell CT87A
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Honeywell CT87A.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Honeywell CT87A, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Honeywell CT87A. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Honeywell CT87A.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Honeywell CT87A, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Honeywell CT87A par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Honeywell CT87A.

Le manuel d’utilisation complet Honeywell, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Honeywell CT87A - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Honeywell CT87A, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHoneywell CT87A qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Honeywell CT87A - qui devraient nous aider dans les premières étapes lors de l'utilisation Honeywell CT87A
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Honeywell CT87A
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Honeywell CT87A dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Honeywell CT87A?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Honeywell CT87A, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Honeywell CT87A il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)