Français dropdown-ico

Manuel d’utilisation NEC MDview 213

33 pages Non applicable
Télécharger

Aller à la page of 33

Summary
  • NEC MDview 213 - page 1

    MDview Series User ’ s Guide MDview Series User ’s Guide Rev .5 ...

  • NEC MDview 213 - page 2

    Index W arning, Caution ............................................................................................................... ......... English-1 Declaration .................................................................................................................... .............. English-1 Contents ............................... ...

  • NEC MDview 213 - page 3

    English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET . DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SER VICING T O QUALIFIED SERVICE PERSONNEL. ...

  • NEC MDview 213 - page 4

    English-2 This Quick Reference Guide refers to the following NEC MDview Series 2 models - MDview 193 19" Display , 1.3 mega-pixel = 1280 x 1024 resolution (L195RR) - MDview 202 20" Display , 2.0 mega-pixel = 1600 x 1200 resolution (L205GR) - MDview 213 21" Display , 2.0 mega-pixel = 1600 x 1200 resolution (L215GW) - MDview 242 24&quo ...

  • NEC MDview 213 - page 5

    English English-3 Contents Y our new NEC monitor box* should contain the following: • MDview 193, 202, 213, 242 or 262 monitor with tilt/swivel/pivot/height adjust stand • Power Cord (European Continental) • Power Cord (UK) •V ideo Signal Cable (15-pin mini D-SUB male to DVI-A) •V ideo Signal Cable (DVI-D to DVI-D cable) • Quick Referen ...

  • NEC MDview 213 - page 6

    English-4 Figure C.1 Figure C.2 Highest Stand Position Quick Start To attach the LCD monitor to your system, follow these instructions: 1. T urn off the power to your computer . 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.1 ). T ighten all screws. For the ...

  • NEC MDview 213 - page 7

    English English-5 Figure E.1 V acation Switch Power Button Figure C.3 Figure D.1 Figure D.2 Figure C.4 7. Hold all cables firmly and place the cable cover onto the stand ( Figure D.1 ). T o remove the cable cover , lift the cover off as shown in Figure D.2 . 8. Connect one end of the power cord to the AC inlet on the back of the monitor and the oth ...

  • NEC MDview 213 - page 8

    English-6 Tilt Grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired ( Figure TS.1 ). Figure TS.1 Swivel Grasp both sides of the monitor screen with your hands and adjust the swivel as desired ( Figure TS.2 ). NOTE: Handle with care when tilting the monitor screen. 4. Place one hand around the base and one ...

  • NEC MDview 213 - page 9

    English English-7 Figure S.1 4. Place one hand around the base and one hand on the Quick Release Lever . Move the Quick Release Lever in the direction indicated by the arrows ( Figure S.2 ). 5. Lift up the bottom of the stand to unhook it from the monitor ( Figure S.3 ). The monitor can now be mounted using and alternate method. Reverse process to ...

  • NEC MDview 213 - page 10

    English-8 Controls OSD (On-Screen-Display) control buttons on the front of the monitor function as follows: To access OSD menu, press any of the control buttons (EXIT , LEFT , RIGHT , UP , DOWN). To change signal input, press the SELECT button. NOTE: OSD must be closed in order to change signal input. * The “LEFT/RIGHT” and “UP/DOWN” button ...

  • NEC MDview 213 - page 11

    English English-9 ECO MODE Decreases the amount of power consumed by reducing the brightness level. 1: Decreases the brightness by 25%. 2: Decreases the brightness by 50%. CUSTOM: Decreases the brightness level as determined by the user . Refer to the Advanced OSD menu for custom setting instructions. AUTO BRIGHTNESS There are three settings for Au ...

  • NEC MDview 213 - page 12

    English-10 AUTO FINE (Analog input only) This function automatically and periodically adjusts the “FINE” setting for change in signal condition. This function adjusts approximately every 33 minutes. EXP ANSION Sets the zoom method. FULL: The image is expanded to the MDview model’s native mode, regardless of the resolution. ASPECT : The image ...

  • NEC MDview 213 - page 13

    English English-11 OFF TIMER Monitor will automatically power-down when the end user has selected a pre-determined amount of time. Before powering off, a message will appear on the screen asking the user if they want to delay the turn of f time by 60 minutes. Press any OSD button to delay the turn off time. IPM The Intelligent Power Manager allows ...

  • NEC MDview 213 - page 14

    English-12 RESOLUTION NOTIFIER This optimal resolution depends on the MDview model’s native resolution. If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not at the respective MDview model’ s native resolution - 1280 x 1024 or 1600 x 1200 or 1920 x 1200. HOT KEY Y ou can adjust the bri ...

  • NEC MDview 213 - page 15

    English English-13 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOUR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servici ...

  • NEC MDview 213 - page 16

    English-14 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slightly downward ...

  • NEC MDview 213 - page 17

    English English-15 Specifications - MDview 193 Monitor Specifications NEC MDview 193 Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 48.2 cm/19.0 inches crystal display (LCD); 0.294 mm dot pitch; Native Resolution (Pixel Count): 1280 x 1024 250 cd/m 2 white luminence; 100 ...

  • NEC MDview 213 - page 18

    English-16 Specifications - MDview 202 Monitor Specifications NEC MDview 202 Monitor Notes LCD Module Diagonal: 51 cm/20.1 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 51 cm/20.1 inches crystal display (LCD); 0.255 mm dot pitch; Native Resolution (Pixel Count): 1600 x 1200 280 cd/m 2 white luminence; 700:1 contrast ...

  • NEC MDview 213 - page 19

    English English-17 Specifications - MDview 213 Monitor Specifications NEC MDview 213 Monitor Notes LCD Module Diagonal: 54 cm/21.3 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 54 cm/21.3 inches crystal display (LCD); 0.270 mm dot pitch; Native Resolution (Pixel Count): 1600 x 1200 300 cd/m 2 white luminence; 1000:1 ...

  • NEC MDview 213 - page 20

    English-18 Specifications - MDview 242/242-2 Monitor Specifications NEC MDview 242/242-2 Monitor Notes LCD Module Diagonal: 61.1 cm/24.1 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 61.1 cm/24.1 inches liquid crystal display (LCD); 0.270 mm dot Native Resolution (Pixel Count): 1920 x 1200 pitch; 320 cd/m 2 (250 cd/m 2 *3 p ...

  • NEC MDview 213 - page 21

    English English-19 Specifications - MDview 262/262-2 Monitor Specifications NEC MDview 262/262-2 Monitor Notes LCD Module Diagonal: 64.9 cm/25.5 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 64.9 cm/25.5 inches liquid crystal display (LCD); 0.287 mm dot Native Resolution (Pixel Count): 1920 x 1200 pitch; 400 cd/m 2 white lu ...

  • NEC MDview 213 - page 22

    English-20 Features Ambix3 T echnology: T riple input technology allowing up to 3 input sources to be connected to a single monitor . The DVI-I connector supports both analog and digital input signals. Legacy analog input is supported using a traditional 15-pin VGA connector. Ambi x3 provides traditional technology compatibility for analog as well ...

  • NEC MDview 213 - page 23

    English English-21 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make ...

  • NEC MDview 213 - page 24

    English-22 Appendix If you need detailed information about the controls, please use the advanced menu. <How to use the advanced menu> •T urn of f your monitor . •T urn on your monitor by pushing the “POWER” and “INPUT/SELECT” button at the same time for at least one second simultaneously . Then press the control buttons (EXIT , LE ...

  • NEC MDview 213 - page 25

    English English-23 T ag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust. (Analog input only) G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust. (Analog input only) B-H.position Adjusts the position of the blue component of ...

  • NEC MDview 213 - page 26

    English-24 H. Size Adjusts the horizontal size of the screen. (Analog input only) If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be performed using the “H.Size (V .Size)” function (dot clock). For this a Moiré test pattern could be used. This function may alter the width of the picture. U ...

  • NEC MDview 213 - page 27

    English English-25 T ag6 Color Control Colour Control Systems: Seven preset colour settings. For preset settings 1, 2, 3 and 5, the following levels can be adjusted: TEMPERA TURE: Adjust the white temperature by increasing or decreasing this setting. A lower colour temperature will make the screen reddish and a higher colour temperature will make t ...

  • NEC MDview 213 - page 28

    English-26 OFF MODE The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of inactivity . The IPM has three settings. OFF: Monitor does not go into power save mode when the input signal is lost. ST ANDARD: Monitor enters power save mode automatically when the input signal is lost. OPTION: Monitor enters p ...

  • NEC MDview 213 - page 29

    English English-27 BOOT LOGO The NEC logo is briefly displayed after the monitor is powered on. This feature can be turned on or off in the OSD. Note: If the “EXIT” button is kept pressed while NEC logo is displayed, the BOOT LOGO menu will appear . It is possible to change the BOOT LOGO setting to OFF . Signal Information Signal information ca ...

  • NEC MDview 213 - page 30

    English-28 Input Setting Video Bandwidth (Analog input only): It is used when the unnecessary noise from computer appears on a screen. It is strong ineffective, so that a number becomes small. Press “Left” or “Right” to select. Sync Threshold (Analog input only): Adjusts the slice level of a synchronization signal. Press “SELECT” to mov ...

  • NEC MDview 213 - page 31

    English English-29 T agC Schedule Programs the monitor ’s working schedule. Schedule the power on and power of f with hour and a day of the week. Also sets the input port. This OSD can’t remove except EXIT . Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated. ...

  • NEC MDview 213 - page 32

    English-30 PICTURE MODE function - MDview 242-2 and 262-2 Choose the Picture mode that is most suitable for the type of content that is shown. There are five types of mode (ST ANDARD, sRGB, PROGRAMMABLE, Adobe ® RGB and MEDICAL). •T o access the Picture mode, press Reset button while OSD menu is not showing. •T o select the mode, press the Lef ...

  • NEC MDview 213 - page 33

    English English-31 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent ...

Fabricant NEC Catégorie Monitor

Les documents que nous recevons du fabricant de l'appareilNEC MDview 213 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques NEC
- manuels d’utilisations MDview 213
- fiches produit NEC
- dépliants
- ou étiquettes-énergie NEC MDview 213
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation NEC MDview 213.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation NEC MDview 213, manuels d’entretien, brefs manuels ou manuels de l’utilisateur NEC MDview 213. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit NEC MDview 213.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil NEC MDview 213, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser NEC MDview 213 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs NEC MDview 213.

Le manuel d’utilisation complet NEC, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel NEC MDview 213 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières NEC MDview 213, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lNEC MDview 213 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil NEC MDview 213 - qui devraient nous aider dans les premières étapes lors de l'utilisation NEC MDview 213
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de NEC MDview 213
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service NEC MDview 213 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de NEC MDview 213?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec NEC MDview 213, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec NEC MDview 213 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)