Français dropdown-ico

Manuel d’utilisation Pelco C1498M-A

20 pages 0.15 mb
Télécharger

Aller à la page of 20

Summary
  • Pelco C1498M-A - page 1

    Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 • DataFAX (1-559) 292-0435 DD5T Series Dome Drive Installation/ Operation Manual C ...

  • Pelco C1498M-A - page 2

    2 Pelco Manual C1498M-A (7/99) LIST OF ILLUSTRA TIONS Figur e Page 1 System Components (In-Ceiling Model Shown) ................................................ 3 2 Backlight ........................................................................................................... 12 LIST OF T ABLES T able Page A Switch Settings for SW1 .......... ...

  • Pelco C1498M-A - page 3

    Pelco Manual C1498M-A (7/99) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Observe the following warnings before installing and using this product. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, ...

  • Pelco C1498M-A - page 4

    4 Pelco Manual C1498M-A (7/99) 2. Set the switches on the bottom of the dome drive. Refer to T able A for the settings for SW1, and T able B and T able C for SW2. 3. Install the dome drive in the back box. Line up the green tab and red tab on the dome drive with the green label and red label on the back box. Raise the dome drive into the back box a ...

  • Pelco C1498M-A - page 5

    Pelco Manual C1498M-A (7/99) 5 Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ...

  • Pelco C1498M-A - page 6

    6 Pelco Manual C1498M-A (7/99) Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 57 ON OFF OFF ON ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF OFF 59 ON ON OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF OFF 63 ON ON ON ON ON ON OFF OFF 64 OFF OFF OFF OFF OFF OFF ...

  • Pelco C1498M-A - page 7

    Pelco Manual C1498M-A (7/99) 7 Continued on next page 1 13 ON OFF OFF OFF ON ON ON OFF 1 14 OFF ON OFF OFF ON ON ON OFF 1 15 ON ON OFF OFF ON ON ON OFF 1 16 OFF OFF ON OFF ON ON ON OFF 1 17 ON OFF ON OFF ON ON ON OFF 1 18 OFF ON ON OFF ON ON ON OFF 1 19 ON ON ON OFF ON ON ON OFF 120 OFF OFF OFF ON ON ON ON OFF 121 ON OFF OFF ON ON ON ON OFF 122 OFF ...

  • Pelco C1498M-A - page 8

    8 Pelco Manual C1498M-A (7/99) Continued on next page 169 ON OFF OFF ON OFF ON OFF ON 170 OFF ON OFF ON OFF ON OFF ON 171 ON ON OFF ON OFF ON OFF ON 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OFF ON OFF ON 174 OFF ON ON ON OFF ON OFF ON 175 ON ON ON ON OFF ON OFF ON 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON O ...

  • Pelco C1498M-A - page 9

    Pelco Manual C1498M-A (7/99) 9 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 231 ON ON ON OFF OFF ON ON ON 232 OFF OFF OFF ON OFF ON ON ON 233 ON OFF OFF ON OFF ON ON ON 234 OFF ON OFF ON OFF ON ON ON 235 ON ...

  • Pelco C1498M-A - page 10

    10 Pelco Manual C1498M-A (7/99) P AN AND TIL T FUNCTIONS Use your controller ’s joystick to control pan and tilt operation. • Fixed-Speed Controllers - Pan and tilt operation is at a fixed speed; the controller determines the speed. • Variable-Speed Contr ollers - Depending on the joystick’s position, standard pan operation ranges from 0.5 ...

  • Pelco C1498M-A - page 11

    Pelco Manual C1498M-A (7/99) 11 Software controls scan limit stops. When the dome reaches one, it immediately reverses direction. Refer to the Limit Stops section to program the scan limit stops. Program preset 96 (29) to stop a scan. Any pan and tilt or lens command also stops a scan. P ARK If the dome does not receive any commands for a specified ...

  • Pelco C1498M-A - page 12

    12 Pelco Manual C1498M-A (7/99) CM9750 1. T urn the KEY SWITCH to the ON position. 2. Press the PROG key . PROGRAM appears on the LCD screen. 3. Press the PRES key . The PRESET prompt appears. 4. Enter 95 and press the ENTER key . The main menu appears. 5. T urn the KEY SWITCH to the OFF position. CM9760 1. In the default menu, select DEF . The Def ...

  • Pelco C1498M-A - page 13

    Pelco Manual C1498M-A (7/99) 13 T urning off power to the dome does not reset the camera. Camera settings are retained in memory , and when power is restored, the settings are the same as when the camera was turned off. T o reset the camera: 1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera. 2. Press the ...

  • Pelco C1498M-A - page 14

    14 Pelco Manual C1498M-A (7/99) 2. If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera. 3. Press the Iris Open button to enter the Camera submenu. 4. Move the joystick up or down to position the cursor beside Auto-Iris. 5. Press the Iris Open button. Another menu will appear with auto iris mo ...

  • Pelco C1498M-A - page 15

    Pelco Manual C1498M-A (7/99) 15 SHARPNESS The two modes for adjusting the picture sharpness are automatic and manual. T o change the mode: 1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera. 2. Press the Iris Open button to enter the Camera submenu. 3. Move the joystick up or down to position the cursor be ...

  • Pelco C1498M-A - page 16

    16 Pelco Manual C1498M-A (7/99) • Park – The dome moves to preset 1 when the power-up sequence finishes. The only text on the screen is the preset label (if any). • Scan Auto – The dome initiates scan mode when the power-up sequence finishes. Again, there is no text. • Scan Frame – The dome initiates a frame scan when the power-up seque ...

  • Pelco C1498M-A - page 17

    Pelco Manual C1498M-A (7/99) 17 SCAN LIMIT STOPS Refer to the documentation for your control system for programming presets, then do the following: 1. Make sure limit stops are turned ON (refer to the Limit Stops section), then exit the menu. 2. Push the joystick left until you reach the limit you want the camera to go to on the left. 3. Program pr ...

  • Pelco C1498M-A - page 18

    18 Pelco Manual C1498M-A (7/99) 4. Remove the dome drive: Push in on the green drive eject tab on the side of the dome drive and gently rock the dome drive to release the latch. When the green latch releases, pull the dome down. 5. Do one of the following: • If your problem was that the unit would not operate: Proceed to step 6. • If your probl ...

  • Pelco C1498M-A - page 19

    Pelco Manual C1498M-A (7/99) 19 SPECIFICA TIONS MECHANICAL Pan Movement: 360 ° continuous pan rotation Vertical Tilt: Unobstructed +2 ° to -92 ° Manual Pan Speed: 0.5 ° -80 ° /sec manual operation, 150 ° /sec turbo Manual Tilt Speed: 0.5 ° -40 ° /sec Preset Speeds Pan: 250 ° /sec Tilt: 200 ° /sec Fixed-Speed Controller Pan: 30 ° /sec Til ...

  • Pelco C1498M-A - page 20

    20 Pelco Manual C1498M-A (7/99) REVISION HISTOR Y Manual # Date Comments C1498M 2/99 Original version. 3/99 Removed reference to line synchronization. Added material on auto iris. Added FCC notice. C1498M-A 7/99 Revised the preset tilt speed from 100 to 200 degrees/second. Added model number and specifications for a P AL camera. Revised T roublesho ...

Fabricant Pelco Catégorie Security Camera

Les documents que nous recevons du fabricant de l'appareilPelco C1498M-A peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Pelco
- manuels d’utilisations C1498M-A
- fiches produit Pelco
- dépliants
- ou étiquettes-énergie Pelco C1498M-A
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Pelco C1498M-A.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Pelco C1498M-A, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Pelco C1498M-A. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Pelco C1498M-A.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Pelco C1498M-A, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Pelco C1498M-A par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Pelco C1498M-A.

Le manuel d’utilisation complet Pelco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Pelco C1498M-A - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Pelco C1498M-A, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPelco C1498M-A qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Pelco C1498M-A - qui devraient nous aider dans les premières étapes lors de l'utilisation Pelco C1498M-A
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Pelco C1498M-A
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Pelco C1498M-A dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Pelco C1498M-A?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Pelco C1498M-A, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pelco C1498M-A il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)