Français dropdown-ico

Manuel d’utilisation Harbor Freight Tools 90178

19 pages 3.04 mb
Télécharger

Aller à la page of 19

Summary
  • Harbor Freight Tools 90178 - page 1

    CEMENT MIXER - 3.5 CUBIC FOOT WITH BRIGGS & STRA TT ON 3.5 HP ENGINE Model 90178 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .harborfreight.com Copyright 2003 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may ...

  • Harbor Freight Tools 90178 - page 2

    PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover . Keep this manual and invoice in a safe a ...

  • Harbor Freight Tools 90178 - page 3

    6. Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, back injury , etcetera. 7. Industrial applications must follow OSHA requirements. 8. Stay alert. W atch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand. 9. Check for damaged ...

  • Harbor Freight Tools 90178 - page 4

    3. Keep a safe clearance around the Cement Mixer . Keep all people (except the operator) a minimum of six feet from the Mixer during operation. 4. Keep all guards in place and in proper working condition. 5. Remove adjusting tools, shovels, hand trowels, etc. Make sure all adjusting tools, shovels, hand trowels, and other tools and equipment are re ...

  • Harbor Freight Tools 90178 - page 5

    Dispose of fluids and cleaning materials in accordance with all local, state, or federal codes and regulations. Store oil rags in a covered metal container . 17. Never store fuel or other flammable materials near the Cement Mixer . 18. Do not smoke, or allow sparks, flames, or other sources of ignition around the Engine (part #14) and its fuel tank ...

  • Harbor Freight Tools 90178 - page 6

    SKU 90178 P AGE 6 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts List on page 18 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y INSTRUCTIONS NOTE: For additional references to the parts listed in the fo ...

  • Harbor Freight Tools 90178 - page 7

    SKU 90178 P AGE 7 WHEEL (#5) PIN (#4) FLA T W ASHER (#3) FIGURE B W ashers (part #10), two Spring Washers (part #9), and two Nuts (part #8). (See Figure C.) HEX BOL T (#7) FLA T W ASHER (#10) SPRING W ASHER (#9) NUT (#8) HEX BOL T (#7) FLA T W ASHER (#10) SPRING W ASHER (#9) NUT (#8) LOWER DRUM (#44) SUPPORT ARM (#31) FIGURE C 4. Align the two moun ...

  • Harbor Freight Tools 90178 - page 8

    HEX HEAD BOL T (#27) FLA T W ASHER (#10) NOT SHOWN SPRING W ASHER (#9) NOT SHOWN NUT (#8) NOT SHOWN DEGREE ADJUSTING PLA TE (#37) DEGREE ADJUSTING ARM (#38) SPRING (#39) BOL T (#40) NUT (#8) PIVOT ARM OF DEGREE ADJUSTING PLA TE (#37) FIGURE D 6. Secure the Degree Adjusting Arm (part #38) to the Pivot Shaft of the Degree Adjusting Plate (part #37), ...

  • Harbor Freight Tools 90178 - page 9

    7. Align the six mounting holes of the Connector Seal (part #45) with the six mount- ing holes in the Upper Drum (part #47). Then, glue (not included) the Connector Seal to the Upper Drum. NOTE: Make sure the Connector Seal lays flat on the Upper Drum to ensure a proper seal. (See Figure E.) UPPER DRUM (#47) CONNECTOR SEAL (#45) MOUNTING HOLE FIGUR ...

  • Harbor Freight Tools 90178 - page 10

    SKU 90178 P AGE 10 Flat W ashers (part #10), four Spring W ashers (part #9), and four Nuts (part #50) to secure the two Mixing Blades to the inside Drum assembly . (See Figure G.) MIXING BLADE (#46) MOUNT WITH V-SHAPED BENDS POINTING TO LEFT . DRUM ASSEMBL Y (#44, #47) FIGURE G 1 1. Insert the Fixing Plate (part #18) onto the Shaft (part #35). (See ...

  • Harbor Freight Tools 90178 - page 11

    FIGURE I SHAFT (#35) FIXING PLA TE (#18) FIGURE J INNER COVER (#23) SHAFT (#35) SKU 90178 P AGE 1 1 14. Align the four mounting holes in the Engine Mount Plate (part #12) with the two mounting slots located in the lower portion of the Inner Cover (part #23). Position the Small Fixing Plate (part #51) against the vertical arm of the Stand (part #1). ...

  • Harbor Freight Tools 90178 - page 12

    HEX HEAD BOL T (#27) FLA T W ASHER (#19) SPRING W ASHER (#20) NUT (#21) HEX HEAD BOL T (#27) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#21) BOL T (#48) FLA T W ASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WA ...

  • Harbor Freight Tools 90178 - page 13

    16. Unscrew the Thrust Screw (part #17) located in the Large Pulley (part #26). Align the Keyway Slot of the Large Pulley with the Key on the Shaft (part #35). Using a hammer , carefully tap the Large Pulley onto the Shaft. Retighten the Thrust Screw to secure the Large Pulley in place. (See Figure M.) FIGURE M LARGE PULLEY (#26) SHAFT (#35) 17. Lo ...

  • Harbor Freight Tools 90178 - page 14

    18. Align the four mounting holes in the base of the Engine (part #14) with the four mounting slots in the Engine Mount Plate (#12). Insert four Hex Bolts (part #7) downward through the mounting holes and mounting slots. Insert one Flat W asher (part #10) and one Spring W asher (part #9) on each of the four Bolts. Then, finger tighten only one Nut ...

  • Harbor Freight Tools 90178 - page 15

    OPERA TING INSTRUCTIONS 1. IMPORT ANT : AL W A YS make sure the crankcase of the gasoline Engine (part #14) is filled to the proper level with a premium quality , 30-weight, non-detergent engine oil prior to starting the engine. Failure to do so will result in damage to the Engine and void its warranty . Refer to the Engine manufacturer ’s instru ...

  • Harbor Freight Tools 90178 - page 16

    SKU 90178 P AGE 16                        ? ...

  • Harbor Freight Tools 90178 - page 17

    1 1. After discharging the cement mix, raise the Degree Adjusting Arm (part #38) up to its original position. (See Figure Q.) 12. Repeat Steps #5 through #1 1 if more cement mix is required. 13. When finished, make sure to thoroughly clean the inside of the Drum (parts #44, #47). (See “Inspection, Maintenance, And Cleaning” Section.) SKU 90178 ...

  • Harbor Freight Tools 90178 - page 18

    NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90178 P AGE 18 P ARTS LIST * See Briggs & Stratton Engine Parts List and Assembly Diagram for available replacement parts. ® PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED T ...

  • Harbor Freight Tools 90178 - page 19

    ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90178 P AGE 19 51: SMALL FIXING PLA TE NOT SHOWN. ...

Fabricant Harbor Freight Tools Catégorie Window

Les documents que nous recevons du fabricant de l'appareilHarbor Freight Tools 90178 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Harbor Freight Tools
- manuels d’utilisations 90178
- fiches produit Harbor Freight Tools
- dépliants
- ou étiquettes-énergie Harbor Freight Tools 90178
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Harbor Freight Tools 90178.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Harbor Freight Tools 90178, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Harbor Freight Tools 90178. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Harbor Freight Tools 90178.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Harbor Freight Tools 90178, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Harbor Freight Tools 90178 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Harbor Freight Tools 90178.

Le manuel d’utilisation complet Harbor Freight Tools, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Harbor Freight Tools 90178 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Harbor Freight Tools 90178, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHarbor Freight Tools 90178 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Harbor Freight Tools 90178 - qui devraient nous aider dans les premières étapes lors de l'utilisation Harbor Freight Tools 90178
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Harbor Freight Tools 90178
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Harbor Freight Tools 90178 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Harbor Freight Tools 90178?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Harbor Freight Tools 90178, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Harbor Freight Tools 90178 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)