Français dropdown-ico

Manuel d’utilisation Maytag MED5100DW

24 pages 5.66 mb
Télécharger

Aller à la page of 24

Summary
  • Maytag MED5100DW - page 1

    1 W10676165A W10676166A - SP T able of Contents DR YER SAFETY ......................................................................... 2 INST ALLA TION REQUIREMENTS ............................................. 3 T ools and Parts ...................................................................... 3 LOCA TION REQUIREMENTS ....................... ...

  • Maytag MED5100DW - page 2

    2 DR YER SAFETY IMPORT ANT : When discarding or storing your old clothes dryer , remove the door . ...

  • Maytag MED5100DW - page 3

    3 INST ALLA TION REQUIREMENTS TOOLS AND P AR TS Gather the requir ed tools and parts before starting installation. T ools needed: Flat-blade screwdriver #2 Phillips screwdriver Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Wire stripper (dir ect wire installations) Tin snips (new vent installations) 1/4" and 5/16&qu ...

  • Maytag MED5100DW - page 4

    4 DR YER DIMENSIONS Back view: 6 1 / 2 " (165 mm) 29 7 / 8 "* (759 mm) 3 1 / 2 "* (89 mm) 6 1 / 8 "* (156 mm) 14 3 / 8 " (365 mm) 3 / 4 "* (18 mm) NOTE: Most installations requir e a minimum of 5" (127 mm) clearance behind dryer for exhaust vent with elbow . See “V enting Requirements.” LOCA TION REQUIREMENTS ...

  • Maytag MED5100DW - page 5

    5 Installation spacing for recessed ar ea or closet installation All dimensions show recommended and minimum spacing allowed. ■ Additional spacing should be considered for ease of installation and servicing. ■ Additional clearances might be requir ed for wall, door , oor moldings, and dryer venting. ■ Additional spacing should be considere ...

  • Maytag MED5100DW - page 6

    6 Then choose a 4-wire power supply cor d with ring or spade terminals and UL listed strain relief. The 4-wir e power supply cord, at least 4 ft. (1.22 m) long, must have four 10-gauge copper wires and match a 4-wir e receptacle of NEMA T ype 14-30R. The ground wir e (ground conductor) may be either green or bar e. The neutral conductor must be ide ...

  • Maytag MED5100DW - page 7

    7 For direct wir e installations: ELECTRIC INST ALLA TION For power supply cord installations: Remove hold-down screw and terminal block cover . 1. Choose electrical connection type Power supply cord 4-wir e receptacle (NEMA T ype 14-30R). Go to “Power Supply Cord Connection.” 3-wire dir ect connection: Go to “Direct Wir e Connection.” 4-wi ...

  • Maytag MED5100DW - page 8

    8 Power supply cord strain r elief: 4-Wire Power Supply Cor d Connection Power Supply Cor d Connection 4-wire r eceptacle (NEMA type 14-30R) 4-prong plug Spade terminals with upturned ends Ring terminals IMPORT ANT : A 4-wire connection is requir ed for mobile homes and where local codes do not permit the use of 3-wir e connections. 1. Prepare to c ...

  • Maytag MED5100DW - page 9

    9 3-wire r eceptacle (NEMA type 10-30R) 3-prong plug Spade terminals with upturned ends Ring terminals 3. Connect remaining wires 2. Connect neutral wire C B 4. Connect remaining wires 1. Remove center screw B 3. Connect ground wire F A Connect remaining wir es under outer terminal block screws. Tighten screws. Finally , reinsert tab of terminal bl ...

  • Maytag MED5100DW - page 10

    10 4-Wire Dir ect Wire Connection IMPORT ANT : A 4-wire connection is r equired for mobile homes and where local codes do not permit 3-wir e connections. Dir ect Wire Connection Direct wir e strain relief 1. Prepare your 4-wir e cable for direct connection 1" (25 mm) 3 1 ⁄ 2 " (89 mm) 5" (127 mm) 2. Prepare to connect neutral gr ou ...

  • Maytag MED5100DW - page 11

    11 1. Prepare your 3-wir e cable for direct connection 1" (25 mm) 3½" (89 mm) 2. Remove center screw B 5. Connect remaining wires 4. Connect ground wire F A Remove center terminal block screw (B). Direct wir e cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 3 1 / 2 " (89 mm) of outer covering fr ...

  • Maytag MED5100DW - page 12

    12 Connect neutral ground wir e (E) and neutral wire (white or center wire) (C) of power supply cor d or cable under center , terminal block screw (B). Tighten scr ew . Place ends of remaining wir es under outer terminal block screws. Tighten scr ews. Connect a separate copper ground wir e (G) under the green external ground conductor screw (A) to ...

  • Maytag MED5100DW - page 13

    13 Louvered Hood Angled Hood Box Hood Exhaust hoods: Elbows: Recommended Styles: ■ 45° elbows provide better airow than 90° elbows. Clamps: ■ Use clamps to seal all joints. ■ Exhaust vent must not be connected or secured with scr ews or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape. ■ An ...

  • Maytag MED5100DW - page 14

    14 The “V ent System Charts” provide venting requir ements that will help achieve best drying performance. Special provisions for mobile homes: Exhaust vent must be securely fastened to a noncombustible portion of mobile home and must not terminate beneath the mobile home. T erminate exhaust vent outside. Determine vent path: ■ Select route t ...

  • Maytag MED5100DW - page 15

    15 Install V ent System 1. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) 2. Connect vent to exhaust hood Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. V ent must t over the exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location usi ...

  • Maytag MED5100DW - page 16

    16 5. Attach long hose to dryer ll valve and tighten coupling Remove protective cap fr om water inlet valve. Attach other end of long hose to ll valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on ll valve connector . Using pliers, tighten the couplings an additional two-thirds turn. NOTE: Do not overtighte ...

  • Maytag MED5100DW - page 17

    17 2. Adjust leveling legs If dryer is not level, prop up using a wood block, use wr ench to adjust legs up or down, and check again for levelness. Once dryer is level, make sure all four legs ar e snug against the oor and dryer does not rock. LEVEL DR YER 1. Level dryer Place level here Not Level LEVEL Not Level Check levelness of dryer from si ...

  • Maytag MED5100DW - page 18

    18 1. Remove door from dryer 2. Move the door strike Using a TORX T25 ® screwdriver , remove the 2 scr ews securing the door strike to the door frame of the dryer . Rotate the strike 180° and attach to the opposite side of dryer door frame, as shown. 3. Remove inner door from outer door Position the door with the inside of the door facing up. Usi ...

  • Maytag MED5100DW - page 19

    19 4. Remove outer window assembly from trim ring Using a Phillips screwdriver , remove the 2 scr ews from the outer window retainer and r otate the outer window assembly clockwise until the square notches line up with the 4 tabs on the trim ring indicated with arrows in the gur e A above. Then lift out the outer window and retainer up and of f ...

  • Maytag MED5100DW - page 20

    20 8. Reinstall hinge and latch on opposite sides Using a TORX T25 ® screwdriver , reinstall the latch plate, latch backing plate, and hinge assembly on the opposite sides from which they were r emoved. 7. Remove hinge and latch Using a TORX T25 ® screwdriver , remove the 3 TORX ® scr ews securing the latch plate and latch backing plate and the ...

  • Maytag MED5100DW - page 21

    21 9. Reinstall inner door assembly Position the door with the inside of the door facing up. Reinstall the 10 screws securing the inner door to the outer door . 10. Reinstall door on dryer Using a TORX T25 ® screwdriver , remove the 4 scr ews on the dryer . Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. S ...

  • Maytag MED5100DW - page 22

    22 3. Remove inner door from outer door Position the door with the inside of the door facing up. Using a Phillips screwdriver , remove the 10 scr ews securing the inner door to the outer door . Lift off the inner door and set aside. 4. Remove hinge and latch Using a TORX T25 ® screwdriver , remove the 3 TORX ® scr ews securing the latch plate and ...

  • Maytag MED5100DW - page 23

    23 Reverse door swing square-shaped door 1. Remove door from dryer Using a TORX T25 ® screwdriver , remove the 4 scr ews securing the door hinge to the dryer and lift up and out to remove the door . Place the door on a soft towel or other non-scratch surface. Retain or set aside the 4 screws. 2. Move the door strike Using a TORX T25 ® screwdriver ...

  • Maytag MED5100DW - page 24

    6. Reattach inner door to outer door Position the inner door on the outer door assembly . Using a Phillips screwdriver , secure with the 13 scr ews removed earlier . 7. Reattach door to dryer Using a TORX T25 ® screwdriver , reinstall the 4 scr ews securing the door hinge to the dryer . 5. Reinstall hinge and latch on opposite sides Using a TORX T ...

Fabricant Maytag Catégorie Dryer

Les documents que nous recevons du fabricant de l'appareilMaytag MED5100DW peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Maytag
- manuels d’utilisations MED5100DW
- fiches produit Maytag
- dépliants
- ou étiquettes-énergie Maytag MED5100DW
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Maytag MED5100DW.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Maytag MED5100DW, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Maytag MED5100DW. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Maytag MED5100DW.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Maytag MED5100DW, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Maytag MED5100DW par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Maytag MED5100DW.

Le manuel d’utilisation complet Maytag, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Maytag MED5100DW - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Maytag MED5100DW, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMaytag MED5100DW qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Maytag MED5100DW - qui devraient nous aider dans les premières étapes lors de l'utilisation Maytag MED5100DW
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Maytag MED5100DW
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Maytag MED5100DW dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Maytag MED5100DW?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Maytag MED5100DW, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Maytag MED5100DW il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)