Français dropdown-ico

Manuel d’utilisation Yamaha ACD1

25 pages 0.41 mb
Télécharger

Aller à la page of 25

Summary
  • Yamaha ACD1 - page 1

    EN Reference Manual ...

  • Yamaha ACD1 - page 2

    ACD1 Reference Manual 2 Contents Introduction............................................. 3 About the documentation ................................. 3 Supported amplifiers ......................................... 3 Setup ................................................................... 3 Terms .................................................. ...

  • Yamaha ACD1 - page 3

    ACD1 Reference Manual 3 Intr oduction About the documentation This document explains mainly the operation and specifications of the A CD1 amplifier control de vice itself. When using the A CD1, y ou will also need to consult various manuals other than this document. ● Manuals other than this document • Please use Amp Editor V ersion 1.1 or la ...

  • Yamaha ACD1 - page 4

    ACD1 Reference Manual 4 Introduction T erms This section explains terminology specific to the A CD1. ■ Amp Editor This is computer application software. W ith this software, you can use your computer to monitor and control the A CD1 and the amplifiers connected to the A CD1. ■ Scene Settings such as Po wer-On/Standby or mute for each amplifi ...

  • Yamaha ACD1 - page 5

    ACD1 Reference Manual 5 Contr ols and Connectors q Display This sho ws information about the scene, the A CD1 itself, or the connected amplifiers. This will light red when an abnormal- ity (a W ARNING or higher alert) occurs. This will also blink blue and white when the Identify operation is performed in Amp Editor. When you turn on the po wer, a ...

  • Yamaha ACD1 - page 6

    ACD1 Reference Manual 6 Controls and Connectors y Ground scre w The A C power cord is a 3-wire type. If the A C outlet used is earthed (grounded), this de vice will be properly earthed as well. Also, grounding the scre w sometimes reduces hum and interference noise. u [A C IN] connector Connect to the A C mains using the supplied A C power cable. F ...

  • Yamaha ACD1 - page 7

    ACD1 Reference Manual 7 Panel operations By pressing b uttons on the panel you can monitor or contr ol various parameters of the A CD1 itself or of the con- nected amplifiers. The f ollowing parameters can be monitor ed/controlled. Category Sub category Operation performed 1. Scene (page 10) Recall Recalls a scene on the specified amplifier . St ...

  • Yamaha ACD1 - page 8

    ACD1 Reference Manual 8 Panel operations The main roles of each b utton are as follo ws. As an example, we’ll explain how to stor e the scene of an amplifier connected to the A CD1. The basic operation is the same f or all parameters. 1. From the HOME scr een, press the [NEXT] button and then use the [ ▲ INC/YES] / [ ▼ DEC/NO] b uttons to se ...

  • Yamaha ACD1 - page 9

    ACD1 Reference Manual 9 Panel operations 5. Use the [ ▲ INC/YES] / [ ▼ DEC/NO] b uttons to select the ID of the amplifier f or which you want to stor e settings. 6. Press the [NEXT] b utton to move to the scene number . 7. Use the [ ▲ INC/YES] / [ ▼ DEC/NO] b uttons to select the scene number that y ou want to store. 8. Press the [NEXT] b ...

  • Yamaha ACD1 - page 10

    ACD1 Reference Manual 10 Panel operations Here’ s how to r ecall or store scenes for a specified amplifier . ■ Recalling a scene (“1. Scene” ➝ “Recall”) Recalls a scene for the specified amplifier . • If you select “ALL ” as the Amp ID , the scene name will not be displayed. • If you select “ALL ” as the Amp ID , ampli ...

  • Yamaha ACD1 - page 11

    ACD1 Reference Manual 11 Panel operations These settings allow y ou to control an amplifier connected to the A CD1. ■ Po wer on/standb y (“2. Amp Contr ol” ➝ “Standby”) Switches the po wer of the specified amplifier between On and Standby . • If you select “ALL ” as the [Amp ID], the power supply status may indicate “Some Sta ...

  • Yamaha ACD1 - page 12

    ACD1 Reference Manual 12 Panel operations This indicates the output lev el of the amp connected to the A CD1. ■ Amplifier output (“3. Output Monitor”) Displays the output le vel for each channel of the specified amplifier . Here y ou can make settings to identify the A CD1 connected to the network and the amplifiers connected to the A CD1 ...

  • Yamaha ACD1 - page 13

    ACD1 Reference Manual 13 Panel operations ■ Identify (“4. Device Setup” ➝ “Identify”) Blinks the “Identify” icon of the corresponding A CD1 in Amp Editor. Here y ou can make overall settings f or the A CD1 and view various types of inf ormation. ■ Bac kup battery chec k (“5. Utility” ➝ “Batter y”) Displays the state of t ...

  • Yamaha ACD1 - page 14

    ACD1 Reference Manual 14 Panel operations ■ LCD bac klight (“5. Utility” ➝ “LCD Bac klight”) This specifies the lit status of the A CD1’ s LCD backlight. ■ Restricting panel operations (“5. Utility” ➝ “P anel Operation”) Here you can turns panel operation lock on/of f. By locking panel operations you can pre vent unintend ...

  • Yamaha ACD1 - page 15

    ACD1 Reference Manual 15 Panel operations ■ Enabling scene recall operations via EMG commands (“5. Utility” ➝ “EMG Scene Setup”) Specifies whether the EMG scene will be recalled when the EMG (Emer - gency) signal is recei ved. The follo wing three types of EMG signal can be recei ved. • EMG command sent from AMX/Crestron • Input si ...

  • Yamaha ACD1 - page 16

    ACD1 Reference Manual 16 Panel operations ■ GPI IN calibration (“5. Utility” ➝ “GPI Calibration”) Calibrates the detected range of the [GPI IN] connector input v oltage. Here y ou can make network settings f or the A CD1. ■ IP Address Mode setting (“6. Netw ork Setup” ➝ “IP Address Mode”) This specifies whether the A CD1’ ...

  • Yamaha ACD1 - page 17

    ACD1 Reference Manual 17 Panel operations ■ Po rt settings f or an external contr oller (“6. Network Setup” ➝ “IP Ctrl P or t #”) Here you can specify the port number that will be used to control the A CD1 from an external de vice such as an AMX or Crestron unit. Here’ s how to initialize the A CD1’ s internal memory . • When you ...

  • Yamaha ACD1 - page 18

    ACD1 Reference Manual 18 Connector wiring This section explains how to wir e the [GPI] and [F A UL T OUTPUT] connectors located on the A CD1’s r ear panel. Be sure to use the supplied Eur oblock connector . If you lose the connector , contact your Y amaha dealer . 1. Loosen the terminal screws. • Use a slotted screwdriver with a blade appro xim ...

  • Yamaha ACD1 - page 19

    ACD1 Reference Manual 19 Connector wiring Connect GPI (General Purpose Interface) de vices (e.g., contr ol- lers) to the rear panel [GPI] connector . Y ou can use GPI to send or r eceive contr ol signals to or from an external de vice. The A CD1 provides 4-port input and 4-port output. • The +V terminals ha ve an output v oltage of 5 V . A maximu ...

  • Yamaha ACD1 - page 20

    ACD1 Reference Manual 20 Connector wiring Y ou can connect a lamp etc. to the r ear panel [F A UL T OUTPUT] connector to indicate that an abnormality has occurred. The [F A UL T OUTPUT] connector consists of NO (Normally Open), C (Common), and NC (Normally Closed). The [F A UL T OUTPUT] connector is a relay circuit, and oper - ates as follo ws. The ...

  • Yamaha ACD1 - page 21

    ACD1 Reference Manual 21 Appendix Messages that may appear in the A CD1’ s display and the appropriate responses ar e listed below . F or more about alert messages, refer to the Amp Editor o wner’ s manual. The A CD1 allows the f ollowing single-byte characters to be displayed and input. Displa y messages Message Response P anel locked! T o pre ...

  • Yamaha ACD1 - page 22

    ACD1 Reference Manual 22 Appendix Tr oubleshooting Symptom P ossible causes Response All scene data sav ed in the ACD1 has disap- peared The power w as tur ned off while the ACD1’ s data was being sa ved Once again synchronize the unit with Amp Editor to transmit the settings from Amp Editor. The internal batter y has run down Go to “5. Utility ...

  • Yamaha ACD1 - page 23

    ACD1 Reference Manual 23 Appendix *1 Suppor ted models XP7000, XP5000, XP3500, XP2500, XP1000, XM4180, XM4080, XH200 Guaranteed cable length: 50m *2 Suppor ted models T5n, T4n, T3n, PC9501N, PC6501N, PC4801N, PC3301N, PC2001N, PC9500N, PC4800N, PC3300N *3 Inputs: 4channels, Outputs: 4channels Outputs: Withstanding V oltage Vmax = 12V (Open) Outputs ...

  • Yamaha ACD1 - page 24

    ACD1 Reference Manual 24 Appendix Unit : mm * Specifications and descr iptions in this owner’ s manual are for inf or mation purposes only . Y amaha Cor p . reserves the right to change or modify products or specifications at any time without prior notice. Since spec- ifications, equipment or options ma y not be the same in every locale, pleas ...

  • Yamaha ACD1 - page 25

    U .R.G., Pro Audio & Digital Musical Instrument Division, Y amaha Corporation © 2009 Y amaha Corporation 911-PO-C0 ...

Fabricant Yamaha Catégorie Stereo Amplifier

Les documents que nous recevons du fabricant de l'appareilYamaha ACD1 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Yamaha
- manuels d’utilisations ACD1
- fiches produit Yamaha
- dépliants
- ou étiquettes-énergie Yamaha ACD1
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Yamaha ACD1.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Yamaha ACD1, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Yamaha ACD1. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Yamaha ACD1.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Yamaha ACD1, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Yamaha ACD1 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Yamaha ACD1.

Le manuel d’utilisation complet Yamaha, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Yamaha ACD1 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Yamaha ACD1, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lYamaha ACD1 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Yamaha ACD1 - qui devraient nous aider dans les premières étapes lors de l'utilisation Yamaha ACD1
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Yamaha ACD1
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Yamaha ACD1 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Yamaha ACD1?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Yamaha ACD1, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Yamaha ACD1 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)