Français dropdown-ico

Manuel d’utilisation Jonsered BC2145

40 pages 2.29 mb
Télécharger

Aller à la page of 40

Summary
  • Jonsered BC2145 - page 1

    FC2145 FC2145S BC2145 FC2145W Oper ator’ s manual (EP A) Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . ...

  • Jonsered BC2145 - page 2

    2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear: • A protective ...

  • Jonsered BC2145 - page 3

    English – 3 CONTENTS Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . Long-term exposure to noise can result in permanent hear ing impairment. So alwa ys use approv ed hearing protection. Maintenance, replacement, or repair of the emission control de vices and system may be perf ormed by any nonroad ...

  • Jonsered BC2145 - page 4

    4 – English INTR ODUCTION Dear customer! Cong ratulations on y our choice to buy a Jonsered product! Y our purchase gives y ou access to prof essional help with repairs and ser vice whenev er this may be necessary . If the retailer wh o sells your machine is not one of our authorized dealers , ask for the address of y our nearest ser vicing deale ...

  • Jonsered BC2145 - page 5

    English – 5 WHA T IS WHA T? What is what on the c learing saw? (BC 2145) 26 27 28 6 3 51 7 4 22 24 33 9 32 8 7 18 20 19 21 4 1 31 21 29 34 34 2 3 2 4 11 30 25 13 12 14 16 15 23 35 36 10 1 Grass b lade 2 Grease fi ller cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop s witch 9 Throttle lock ...

  • Jonsered BC2145 - page 6

    6 – English WHA T IS WHA T? What is what on the c learing saw? (FC 2145, FC 2145 S, FC 2145 W) 24 27 25 26 23 6 3 5 13 11 12 9 7 17 8 14 16 15 21 22 18 1 4 20 18 19 28 29 30 2 3 4 10 31 9 8 7 32 1 Saw b lade 2 Grease fi ller cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop s witch 9 Throttl ...

  • Jonsered BC2145 - page 7

    English – 7 GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PRO TECTION W ear hear ing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection. If you use a visor then you m ust also wear ...

  • Jonsered BC2145 - page 8

    8 – English GENERAL SAFETY PRECA UTIONS Mac hine ′′ ′ ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine ...

  • Jonsered BC2145 - page 9

    English – 9 GENERAL SAFETY PRECA UTIONS Cutting attachment guar d This guard is intended to pre vent loose objects from being thrown to wards the operator . The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cr acked. Replace the guard if it has been e xposed to impa ...

  • Jonsered BC2145 - page 10

    10 – English GENERAL SAFETY PRECA UTIONS F or muf fl ers it is very impor tant that you f ollow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and ser vicing the machine’ s saf ety equipment. Ne ver use a machine that has a f aulty muf fl er . Regularly check that ...

  • Jonsered BC2145 - page 11

    English – 11 GENERAL SAFETY PRECA UTIONS Cutting equipment Saw b lades are intended for cutting fi brous types of w ood. Grass b lades and grass cutters are intended f or cutting coarse grass . A trimmer head is intended for trimming grass . General rules Only use cutting attachments with the guards we recommend! See the chapter on T echnical da ...

  • Jonsered BC2145 - page 12

    12 – English GENERAL SAFETY PRECA UTIONS • The fi ling angle is 15 ° . File alternate teeth to the r ight and those in between to the left. If the blade has been hea vily pitted by stones it ma y be necessary to dress the top edges of the teeth with a fl at fi le, in e xceptional cases. If so , this should be done before fi ling with a rou ...

  • Jonsered BC2145 - page 13

    English – 13 ASSEMBL Y Assembling the handlebar and thr ottle (BC 2145) • Remov e the screw at the rear of the throttle handle . • Slide the throttle handle onto the right side of the handlebar , (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar . •R e fi t the screw in the hole in the rear of th ...

  • Jonsered BC2145 - page 14

    14 – English ASSEMBL Y Assembling the cutting equipment Fitting the blade guar d/combination guar d, grass blade and ball-bearing- mounted suppor t cup • Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use t ...

  • Jonsered BC2145 - page 15

    English – 15 ASSEMBL Y • T ur n the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Inser t the locking pin (C) in the hole to loc k the shaft. • Place the blade (D) and support fl ange (F) on the output shaft. • Fit the nut (G). The nut must be tightened to a torque of 35-50 ...

  • Jonsered BC2145 - page 16

    16 – English ASSEMBL Y Adjusting the harness and c learing saw Standar d harness Safety release At the front is an easily accessible , quick release . Use this if the engine catches fi re or in any other emergency situation that requires you to free y ourself from the machine and harness. Spreading the load on y our shoulders A well-adjusted har ...

  • Jonsered BC2145 - page 17

    English – 17 ASSEMBL Y 4 Adjust the height of the suspension hook as described in the instructions for the standard harness. (Forestry clearing) 5 If you need to lo wer the suspension hook, f or tr imming f or e xample, mov e the suspension strap (A) to the low er mounting point on the backplate . 6 The elastic strap (B) can be tightened to trans ...

  • Jonsered BC2145 - page 18

    18 – English FUEL HANDLING Fuel safety Ne ver star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate . 2 If you ha ve spilt fuel on y ourself or your clothes , change your clothes . W ash any part of your body that has come in contact with fuel. Use soap and water . 3 If the machine is le ...

  • Jonsered BC2145 - page 19

    English – 19 FUEL HANDLING Mixing • Alwa ys mix the gasoline and oil in a clean container intended f or fuel. • Alwa ys star t by fi lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly bef ore fi l ...

  • Jonsered BC2145 - page 20

    20 – English ST AR TING AND ST OPPING Chec k before starting • Check the b lade to ensure that no cracks ha ve f or med at the bottom of the teeth or by the centre hole . The most common reason wh y cracks are f ormed is that shar p corners have been f ormed at the bottom of the teeth while shar pening or that the blade has been used with dull ...

  • Jonsered BC2145 - page 21

    English – 21 ST AR TING AND ST OPPING Start throttle: (FC 2145, FC 2145 S , FC 2145 W , BC 2145) Set the throttle to the star t position by moving the chok e control to the choke position and then returning it to its original position. If the machine is fi tted with a decompression valv e (A): Press the valv e to reduce the pressure in the cylin ...

  • Jonsered BC2145 - page 22

    22 – English W ORKING TECHNIQ UES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out b y the cutting a ...

  • Jonsered BC2145 - page 23

    English – 23 W ORKING TECHNIQ UES W orking methods • Bef ore you star t clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollo ws etc. • Star t at whichev er end of the area is easiest, and clear an open space from which to work. • W or k systematically to and fro across the area, cl ...

  • Jonsered BC2145 - page 24

    24 – English W ORKING TECHNIQ UES • Large stems must be cut from two sides . First determine which direction the stem will f all. Make the fi rst cut on the f elling side. Then fi nish cutting the stem from the other side. Adjust the cutting pressure to match the size of the stem and the hardness of the wood. Small stems require more pressure ...

  • Jonsered BC2145 - page 25

    English – 25 W ORKING TECHNIQ UES Clearing • The clearing technique removes all unw anted vegetation. K eep the trimmer head just above the g round and tilt it. Let the end of the cord strike the ground around trees , posts, statues and the like . CA UTION! This technique increases the wear on the cord. • The cord wears quic ker and must be f ...

  • Jonsered BC2145 - page 26

    26 – English MAINTENANCE Carb uretor Y our Jonsered product has been designed and manuf actured to speci fi cations that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. T o ensure that the engine runs at peak performance and produces as little harmful exhaust fumes as possible after the running-in pe ...

  • Jonsered BC2145 - page 27

    English – 27 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T , if it is necessar y to readjust. First tur n the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly a ...

  • Jonsered BC2145 - page 28

    28 – English MAINTENANCE Adjusting the start throttle speed (BC 2145) The correct star t throttle speed is set by means of an adjuster on the rear of the handle ne xt to the cable. Use this screw (5 mm Allen screw) to increase or decrease the start throttle speed. Proceed as f ollows: 1 Run the machine at idle. 2 Press the star t throttle lock as ...

  • Jonsered BC2145 - page 29

    English – 29 MAINTENANCE Air fi lter The air fi lter must be regularly cleaned to remov e dust and dir t in order to av oid: • Carburettor malfunctions • Star ting problems • Loss of engine power • Unnecessar y wear to engine par ts • Excessive fuel consumption. Clean the fi lter e very 25 hours, or more regularly if conditions are e ...

  • Jonsered BC2145 - page 30

    30 – English MAINTENANCE Winter use Running problems can occur when using the machine in the cold and snowy conditions caused b y: • T oo low engine temperature. • Icing of the air fi lter and carburetor . Special measures are theref ore often required: • P ar tly mask the air inlet on the star ter to increase the working temperature of th ...

  • Jonsered BC2145 - page 31

    English – 31 MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine. Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and ser vice work described in this manual. More e xtensive work must be carried out by an authorised ser vice ...

  • Jonsered BC2145 - page 32

    32 – English TECHNICAL D A T A T echnical data Note 1: Equiv alent sound pressure lev el is calculated as the time-weighted energy total f or sound pressure lev els under v ar ious working conditions with the follo wing time distribution: 1/2 idling and 1/2 max speed. NO TE! Noise pressure at the user’ s ear and vibration on the handles are mea ...

  • Jonsered BC2145 - page 33

    English – 33 TECHNICAL D A T A BC 2145 Appro ved accessories T ype Cutting attachment guard, Ar t. no. Centre hole in blades/cutters , Ø 25,4 mm Output shaft thread M12 Grass b lade/grass cutter Multi 255-3 (Ø 255 3 teeth) 537 28 85-02 Multi 275-4 (Ø 275 4 teeth) 537 28 85-02 Multi 300-3 (Ø 300 3 teeth) 537 28 85-02 Saw b lade Opti XS 200-22 ...

  • Jonsered BC2145 - page 34

    34 – English FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to e xplain the emissions control system warranty on y our 2001 and later small nonroad engine. In U .S. and Canada, new small nonroad engines must be d ...

  • Jonsered BC2145 - page 35

    1 Poly T rim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10 ...

  • Jonsered BC2145 - page 36

    1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII ...

  • Jonsered BC2145 - page 37

    ...

  • Jonsered BC2145 - page 38

    ´®z+R*=¶5`¨ ´®z+R*=¶5`¨ 2,7-3,3 mm .106-.130" 15 cm 6" 15 cm 6" 15 cm 6" 15 cm 6" 1 2 3 5 6 7 10 11 1.) 2.) >1,1 Kw <1,1 Kw 2,7 mm - 9,0 m 3,0 mm - 7,5 m 3,3 mm - 6,0 m 4 8 Auto 55 ...

  • Jonsered BC2145 - page 39

    "Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm T ap n’Go 45 ...

  • Jonsered BC2145 - page 40

    ´®z+R*=¶5`¨ 2005-09-29 ´®z+R*=¶5`¨ 1150102-95 ...

Fabricant Jonsered Catégorie Brush Cutter

Les documents que nous recevons du fabricant de l'appareilJonsered BC2145 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Jonsered
- manuels d’utilisations BC2145
- fiches produit Jonsered
- dépliants
- ou étiquettes-énergie Jonsered BC2145
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Jonsered BC2145.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Jonsered BC2145, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Jonsered BC2145. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Jonsered BC2145.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Jonsered BC2145, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Jonsered BC2145 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Jonsered BC2145.

Le manuel d’utilisation complet Jonsered, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Jonsered BC2145 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Jonsered BC2145, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lJonsered BC2145 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Jonsered BC2145 - qui devraient nous aider dans les premières étapes lors de l'utilisation Jonsered BC2145
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Jonsered BC2145
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Jonsered BC2145 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Jonsered BC2145?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Jonsered BC2145, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Jonsered BC2145 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)